Question about Ford Ranger

Open Question

Ford ranger 2003 connecting rod & main bearing torgue spec

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
ewashmidas
  • 362 Answers

SOURCE: torque specs for the main bearings, connecting rods and heads

Here you go...

Connection Rod Nuts: 37-38 Ft Lbs.
Main Bearing Caps: 55-61 Ft Lbs.
And Head Bolts...

1st - step; - 80 ft./lbs. 2nd - step, loosen all bolts; 3rd - step; - 80 ft./lbs.
69de06e.png

Posted on Jan 24, 2009

Ad
moparownr
  • 667 Answers

SOURCE: main and rod bearing torque specs

do you have a Haynes Manual or Chilton? if not check your local library, they may have one, the specs are in there

Posted on Mar 31, 2009

BPALepine
  • 61 Answers

SOURCE: 99 dodge intrepid specs

Inner main bearing cap bolts:
Torque to 15 ft-lbs, then rotate an additional 1/4 turn

Outer main (windage tray) bearing cap bolts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Main bearing cap cross bolts:
Torque to 250 in-lbs or 20.83 ft-lbs

Connecting road bearing cap nuts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Posted on Apr 22, 2009

AutoDoc
  • 169 Answers

SOURCE: need torque specs for connecting rod and main

Torque in two to three stages.
Connecting rods are 24-26 lb.ft.
Main bearing caps are 41-44 lb.ft.
Hope this helps,Chuck

Posted on Dec 28, 2009

Testimonial: "Thanks for the help Chuck"

  • 701 Answers

SOURCE: need the crankshaft main bearing torque specs and

Hello tlittle3: My name is Roger and I will help you.See the attached image. Be sure to follow steps as it is very inportant. You will notice that you need to index some of the bolts. That is merely turning the bolt a specified degree. The crankshaft tie bolts are the bolts that are in the side of the block. install horizontal. Shold you need further help please just ask. Please rate the answer you received. Thank You for using Fix Ya. Rogera32a1ae.jpg

Posted on Apr 26, 2010

Testimonial: "thanks that what i needed"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Main bearing cap bolt torque specs for a 1999 2.0 Ford engine


See #1; Main bearing diagram
See #2; NM conversion chart

  1. NOTE: The crankshaft must rotate freely; if necessary check and adjust the bearing clearances.Tighten the main bearings and connecting rod bearings.
    1. Tighten the main bearing bolts in two stages.
    • Stage 1: 25 Nm.
    • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
    • Stage 1: 25 Nm.
    • Stage 2: 90 degrees.






# 2) Newton Meters conversion chart:
http://extraconversion.com/energy/newton-meters/newton-meters-to-foot-pounds.html

#1)
25730427-ddvrxh52bv4dwu240r4mw22m-2-0.gif saailer

Jun 05, 2015 | Ford Cars & Trucks

2 Answers

Torque specs,rod bearings,2003 nissan altima 2.5


I need the torque specs for the connecting rod and main be

Sep 10, 2011 | Nissan Altima Cars & Trucks

1 Answer

Need torque specs for 2000 Ford taurus 3.0 flex fuel vehicle rod & main bearings


main bearing caps 56-62 foot pounds connecting rod caps 1st pass 17 foot pounds 2nd pass 32 foot pounds......................HAVE FUN

Jan 15, 2011 | 2000 Ford Taurus

1 Answer

2004 mazda 6 3.0L V6 main bearing caps(bootom end) has 16 bolts need torgue specs please!


Okay, the main bearing caps only have 10 bolts, i think your looking for the connecting rod caps, they have 16 bolts, i will list them both, theres a tightening sequnce for the main bearing caps, these are the caps that hold the crankshaft to the engine block, the connecting rod caps hold the pistons to the crank and they have 16 nuts,For a 2004 mazda 6 with the 3.0 engine the torque specs are as follows.
Connecting rod bolts step 1) 19.2 - 23.6 ft lbs.
step 2) tighten an additional 80 - 100 degrees

Main bearing caps step 1) 32.5 - 33.9 ft. lbs.
step 2) tighten an additional 175 -185 degrees.
heres a diagram for main caps to tighten in order.
hope this is helpful.fc3bff9.gif

Aug 20, 2010 | 2003 Mazda Mazda6

1 Answer

Need torque specs for 1999 Ford 3.0 rod & main bearings


ft lbs

Main Bearing Cap Bolts 75-85 56-62
Connecting Rod Cap Nuts 31-39 23-28

May 27, 2009 | 1999 Ford Taurus

1 Answer

Torque specs


2002 2.0L Duratech.

Don't have 2004 2.3L

  • NOTE: Use new connecting rod bearing cap bolts.
    NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
    Install the bearing caps.
  • Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.
  • Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.
  • Coat the inner side of the bearing shells with engine oil.
  1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
    Tighten the main bearing and connecting rod bearing bolts.
    1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.
96fc939.gif

Apr 28, 2009 | 2004 Ford Focus

2 Answers

99 dodge intrepid specs


Inner main bearing cap bolts:
Torque to 15 ft-lbs, then rotate an additional 1/4 turn

Outer main (windage tray) bearing cap bolts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Main bearing cap cross bolts:
Torque to 250 in-lbs or 20.83 ft-lbs

Connecting road bearing cap nuts:
Torque to 20 ft-lbs, then rotate an additional 1/4 turn

Apr 21, 2009 | 1999 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

231 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...