Question about Dodge Neon

2 Answers

2005 neon has trouble starting and is worse in warmer weather. i have replaced the camshaft position sensor, still have da problem, but the check engine light is off

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

IF YOU GET THE SENSOR FROM OTHER THAN THE DEALER,IT WILL NOT WORK PROPERLY... PRICES ARE NOT TO DIFFERENT FROM DEALER

Posted on Jul 02, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 453 Answers

Check fuel pressure should read 30psi

Posted on May 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced timing belt and water pump on a 2005 dodge neon with a 2.0 it starts and idals great but you press or reve it up it backfires through the intake and pulls up code p0344. whats the problem.


Hi Ricky, I'm glad to help. Below is the possible causes for the P0344 code that you have.



Symptom:
P0344-CAMSHAFT POSITION SENSOR INTERMITTENT
When Monitored and Set Condition:
P0344-CAMSHAFT POSITION SENSOR INTERMITTENT

When Monitored: Engine running or Cranking.
Set Condition: When the failure counter reaches 20. One Trip Fault.
POSSIBLE CAUSES

GOOD TRIP EQUAL TO ZERO
WIRING HARNESS INSPECTION
(K7) 5 VOLT SUPPLY CIRCUIT OPEN OR SHORTED TO GROUND
TONE WHEEL/PULSE RING INSPECTION
CHECKING CKP SIGNAL WITH THE DRBIII
t LAB
CAMSHAFT POSITION SENSOR
(K44) CMP SIGNAL CIRCUIT OPEN
(K44) CMP SIGNAL CIRCUIT SHORT TO GROUND
(K44) CMP SIGNAL CIRCUIT SHORTED TO B+
(K44) CMP SIGNAL CIRCUIT SHORT TO (K7) 5 VOLTS
PCM

Apr 18, 2014 | 2005 Dodge Neon

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

I recently bought a 2005 Dodge Neon, the oil light was coming on so I reported to dealer who replaced oil sensor switch, now the check engine light is on so I bought a pocket scanner and it comes up with...


Trouble Code: P0340

No Camshaft Position Sensor Circuit Failure

Possible Causes:


CMP Sensor connector is damaged, open or it is shorted.CMP Sensor signal circuit is open or shorted to ground or to battery voltage or 5v supply circuit.CMP Sensor 5v supply circuit is open or shorted to ground or to battery voltage.CMP Sensor ground circuit is open.CMP Sensor is damaged or has failed.CKP Sensor is damaged or has failed.PCM has failed.I would make a copy of this and tell him that the camshaft needs to be replace or what ever is causing problem,they probaly know.

Jan 13, 2013 | 2005 Dodge Neon

2 Answers

I keep getting a code P0340.Chrysler has reprogrammed the PCM for a long start issue.I cant seem to get anywhere with it.


P0340 - Camshaft Position Sensor Circuit Malfunction
This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

Symptoms can include:
Hard starting or no start
Rough running / misfiring
Loss of engine power

Causes: A code P0340 could mean one or more of the following has happened:
a wire or connector in the circuit could be grounded/shorted/broken
the camshaft position sensor may have failed
the PCM may have failed
there exists an open circuit
the crankshaft position sensor may have failed

Possible Solutions: With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
Visually inspect all the wiring and connectors in the circuit
Check for continuity in the circuit wiring
Check the operation (voltage) of the camshaft position sensor
Replace the camshaft position sensor as required
Check the crankshaft position circuit as well
Replace circuit wiring and/or connectors as required
Diagnose/replace the PCM as required


Hope helps.

Apr 24, 2011 | 2003 Dodge Neon

1 Answer

I have a 2005 Dodge neon with 157K miles just had the orignal timing belt replaced. When I start the car and the rpms hit about 3400 the car starts cutting out. Now I get the check engine light and when I...


Check your vacuum lines, it sounds like one did not get reconnected correctly. When this happens you check engine to come on and will cause your engine's rpm's to rise.

Apr 08, 2011 | 2005 Dodge Neon

1 Answer

Where is the cam sensor on a 2005 dodge neon sxt 2.0


Camshaft Position Sensor-On top of engine Operation The Engine Management System (EMS) uses the camshaft position sensor to manage sequential fuel injection and as part of misfire diagnosis. The EMS constantly monitors the number of pulses on the signal circuit. The EMS compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the EMS receives an incorrect number of pulses, Diagnostic Trouble Codes (DTCs) should be stored in the EMS. Some engine management systems will then default to multi-port or "gang-fire" injector operation. The camshaft position sensor signal is required to sequence the injector operation to the proper cylinder timing. If the camshaft position sensor or circuit is faulty, most engines will start. However, the EMS misfire diagnostic will likely be affected.
The following symptoms can be caused by an intermittent wiring connections or faulty signal to the EMS.
Related Symptoms
  • Extended crank time with a cold engine
  • Intermittent rough running
  • Unstable idle
  • Bucking
  • Hesitation
  • Stumble
  • Chuggle
  • Poor fuel economy
  • Stalling on acceleration
prev.gif next.gif

Aug 05, 2010 | 2005 Dodge Neon

1 Answer

Just wondering where the Camshaft position sensor in my 2005 Dodge Neon is as I need to replace it.


Removal & Installation 2.0L engine camshaft position sensor location chry_car_2.0_cpsloc.gif

2.4L engine camshaft position sensor location chry_car_2.4turbo_cpsloc.gif

2.0L SOHC Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Brake booster hose and electrical connector from holders on end of cylinder head cover and reposition
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
    • Sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor. Torque sensor mounting screws to 80 in. Lbs. (9 Nm)
    • Brake booster hose and electrical harness in holders on end of valve cover
    • Electrical connectors to camshaft position sensor
2.4L Turbo Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Air cleaner box
    • Plastic clip for the wiring harness from the stud on the valve cover
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose from the valve cover
    • Electrical connectors from camshaft position sensor
    • Camshaft position sensor mounting screws
  3. Remove sensor
To Install:
  1. Install or connect the following:
    • Camshaft position sensor torque sensor mounting screws to 80 in. lbs. (9 Nm)
    • Electrical connectors to camshaft position sensor
    • Nut holding the clip for the oil supply line to the turbo and disconnect the fresh air makeup hose to the valve cover
    • Plastic clip for the wiring harness to the stud on the valve cover
    • Air cleaner box
    • Negative battery cable
prev.gif next.gif

Aug 01, 2010 | 2005 Dodge Neon

1 Answer

My 2004 dodge neon sxt is giving me a p0340 code how do i fix this


A code P0340 could mean one or more of the following has happened:

  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

Hope this is for any assistance.

Dec 13, 2009 | 2004 Dodge Neon

2 Answers

CODE PO 340 SENSOR CIRCUIT CAMSHAFT MALFUNCTION


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.I hope this helps you

Oct 06, 2009 | 2004 Dodge Neon

2 Answers

For what sensor is the code po340 on a dodge neon 04 and how i change.


Hi,
This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.

With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
Thanks.

Jun 28, 2009 | 2004 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

344 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...