Question about 1989 Ford Ranger

1 Answer

Engine coolant sensor location

Where is this located on a 89 ford ranger 2.9 L?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

Behind water pump it's called freeze plug

Posted on Jun 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MAP sensor for 89 Ford Ranger


what exactly are you asking for. were to get one (auto parts store or dealer) or are asking for the wire colour code, were the MAP sensor is located, or how to test it and what vacuum there should be.

Apr 12, 2015 | Ford Cars & Trucks

1 Answer

Location of engine coolant temperature sensor


Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.


12_5_2011_5_38_05_pm.jpg

Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Dec 05, 2011 | 2000 Ford Escort

1 Answer

Have a 95 ford ranger 4 cyl need to know where coolant temp switch is located my gauge is inop i found coolant temp sensor for computor need one for the gauge


On the 4 cylinder motor (2.3L,2.5L), the coolant temp sensor can be located
on the left side rear of the engine, below the cylinder head.

A picture of a typical Coolant Temp Sensor (aka ECT) is below:

9_28_2011_3_19_48_pm.gif
Be sure to partially drain coolant below the level of the sensor to avoid spillage when removing the old part. Best of luck on your repair!
Greg

Sep 28, 2011 | Cars & Trucks

1 Answer

How do i fix code 51 89 ranger 2.3 std trans


That code is for the coolant temp open circuit. More than likely replacing the coolant temp sensor will correc the issue but check/verify the connector and wiring for the temp sensor before you replace.

Feb 24, 2011 | 1989 Ford Ranger

3 Answers

Need know where is the coolant temp sensor on a 1998 ford ranger 2.5 liter


it is located at top of engine at the front hopefully this pic helpsraineman_15.gif

Nov 29, 2010 | 1998 Ford Ranger SuperCab

1 Answer

My Ford ranger 2002 2.3 just started to run hot


Check cooling fan, cooling fan sensor, the sensor's relay if such, coolant level, coolant pump. Sorry for not being able to tell you where are these located, never seen a Ford truck even with closed hood...

Nov 08, 2009 | 2002 Ford Ranger Regular Cab

3 Answers

Where is the ignition module control located on 1996 ranger 2.3 e


It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Apr 08, 2009 | 1996 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2003 Ford Ranger/2.3 O2 sensor - How many and Where located ???


Engine Heated oxygen and catalyst monitor sensors—2.3L engine44e2701.jpg

Jan 16, 2009 | 2003 Ford Ranger Regular Cab

1 Answer

O reading for O2 sensors on 98 Ranger XLT


Yes the 98 ranger has 3 02 sensors,they are located in the exhaust system under vehicle,2 of them
are in front of the cataletic converter and 1 behind it.I replaced mine ,reset the codes and the check
engine light still comes on?

Jan 16, 2009 | 2004 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...