Question about 2008 Jeep Liberty

Open Question

The hood support rod came off,how do u reattach to the frame?

The hood rod detached from the frame,how do you reattach ?

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The windshield washer line detached. How do you reattach it without removing the hood?


Needle nose, make sure that the washer nozzle itself has not broken off. if there is a hard piece of plastic inside of the rubber hose you will need to replace the washer nozzle.

Apr 04, 2016 | 2006 Kia Spectra

1 Answer

Replace side marker lamp near headlight


locate first the screw if it is attached separately from the headlight..if it is attached on the headlight unscrew all bolts attaching the headlights to the main frame..after it you can easily unplug or detach the marker lamp bulb..but if it is separately attach to the headlight open up the hood of your car there you can easily see or find the back part of the marker lamp..simply squeeze it going to the left side to detach the marker lamp..then simply unplug the lamp and replace it easily...

Mar 09, 2011 | 2007 Chevrolet Tahoe

2 Answers

Where is the fuel filter on a 2005 chevy malibu, 4 cylinder


  • Remove the gas cap to relieve pressure in the tank. Lift the hood and locate the fuse panel on the driver's side. Remove the fuel pump fuse. Turn the ignition and attempt to start the car; if it runs, allow it to stall. Turn off the ignition. Remove the negative terminal from the battery.
  • 2 Locate the fuel filter beneath the car between the rear axle and the gas tank. Remove the protective plastic cover with a screwdriver.
  • 3 Remove the carriage bolt securing the filter to the frame. Detach the inlet and outlet fuel line fittings with an open-end wrench. Fuel may spill as you turn the nuts, so have rags or a small container ready.
  • 4 Insert the new filter and secure the fuel lines and carriage bolt. Reattach the plastic cover.
  • 5 Replace the fuel filter fuse, negative battery terminal and gas cap. Close the hood and turn the ignition on. Allow the car to idle for a few minutes while the new filter fills with gasoline.



  • Dec 13, 2010 | 2005 Chevrolet Malibu

    1 Answer

    Trying to remove rear door handle on chrysler lhs 99


    Hello, to remove and replace the rear door try the following:

    1. Disconnect the negative battery cable from the battery of your Chrysler LHS. You can accomplish this with an open end wrench, to prevent any injury or short in the electrical system as you are working on the door lock switch. Place the negative battery cable out of the way so it does not touch any metal parts.


    2. Undo any screws that are holding the lower door panel to the door with a screwdriver. Unclip the plastic hold clips that are attached to the back of the panel by carefully pulling them away by hand.

    3. Locate the electrical connector wires. These wires run behind the panel to the door arm rest and detach each wire connector by hand. Remember how the wires were attached so you can put them back the same way when it is time to reattach them.

    4. Lower the door panel away from the door. Then, remove any screws holding the upper door panel in place. Remove the door handle pull cup that covers the door lock switch and door handle by carefully popping the cover off after you have removed the screws holding it in place.

    5. Detach the upper door panel from the door. You can do this by pulling it away carefully from the plastic clips. Move the upper door panel out of the way and locate the door lock actuator switch. Remove the screws from the actuator switch that are holding it in place and disconnect the electrical wires attached to the back of the switch.

    6. Replace the old door lock actuator switch with a new one. This replacement can occur by connecting the electrical wires to the back of the new switch and reattaching the switch to the door frame with screws. Put the upper door panel back in place, securing it to the door frame with plastic clips and screws.

    7. Reattach the door handle pull cup to the upper door panel with screws. Then, put the lower door panel in place and reattach the electrical wires to the window switches underneath the armrest. Attach the lower door panel to the door frame with plastic clips and screws.

    8. Attach the negative battery cable to the Chrysler LHS battery with the open end wrench.

    Thanks













































    Jul 27, 2010 | 1999 Chrysler LHS

    1 Answer

    The motor on the windows make noise but the glassdoesn't move


    The window actuall sits in a frame inside the door and the motor raises and lowers the frame along with the glass. The arms which connect the motor to the frame can become detached and as the motor runs only the connecting rod moves but the frame holding the window stays in place. If you can reve the interior door panel you'll see exactly what I mean. You may even be able to repair it yourself. If your hesitant about removing the door panel take it to a mechanic or dealer.

    Dec 19, 2009 | 1994 Lincoln Town Car

    1 Answer

    How to remove rear door panels on a 2003 ford f 250to get to door switch


    Tailgate latch, handle and lock
    • Open the tailgate.
    • Remove the two bolts and detach the door stop.
    • Lower the tailgate and remove the tailgate access cover.
    • Disconnect the control rods.
    • Detach the retaining nuts and remove the handle and lock cylinder assembly from the tailgate.
    ...
    Door trim panels
    • Disconnect the cable(s) from the negative battery terminal(s).
    • On manual window equipped models, pull the window crank cover aside, remove the screw and detach the handle.
    • On the front door of power window equipped models Pry up on the retaining clip at the front edge of the armrest and lift the armrest switch control plate out and disconnect the electrical connections,then remove the retaining bolt from the opening.
    • Use a small screwdriver to pry off the courtesy light cover for access to the trim panel retaining bolt.
    • Carefully pry off the mirror trim panel from above the front edge of the door panel.
    • Once all of the bolts are removed, remove the trim panel by gently pullingit up and out .Detach the courtesy light bulb housing from the panel.
    • For access to the inner door components, remove the speaker (if it would interfere with watershield removal) and the screws from the trim piece at the lower trailing corner of the door, then carefully peel the watershield from the door.
    • Remove the screws securing the latch.
    • Working through the large access hole, position the latch as necessary to disconnect the electrical connector and disengage the outside door handle and outside lock cylinder to latch rods and the inside handle-to-Iatch cable.
    • Detach the locking rods by unsnapping The remaining outside handle retaining nut can be reached through the access hole in the door frame and the upper striker the portionof the plastic clip engaging the connecting rod, then pulling the rod out of its locating hole.
    • Position the latch as necessary to disengage the door lock actuator hook. Detach the cable cover and disconnect the cable from the latch. Remove the latch assembly from the door.

    Oct 30, 2009 | 2003 Ford F250 Super Duty Crew Cab

    1 Answer

    Jeep 1992 yJ Outside Door Handle


    ok, the inside panel is cardboard with faux leather. remove the screws holding on the inside handle and the frame of the doorlatch.

    there is a plastic joint that connects the two rods that actuate and open the door. the rods are bent at the end to slip into the white plastic joint. this design is stupid and often times that joint can break, or the rods fall out. solution is to reattach them together and wrap mechanics wire or bend the very ends of the rods so they wont come out.

    its something i cant really explain, but the design is straight forward. also, keep track of the threads on the rod that connects to the claw that meets the striker on the frame of the jeep. if for any reason its not adjusted properly, it will not latch properly.


    Mar 01, 2009 | 1992 Jeep Wrangler

    1 Answer

    Attach hood prop rod 2001 Ford Focus


    First you will need to get a hood prop bushing from pobably your Ford dealer or you can get one from a salvage yard. You may also need a hood rod attchment. In order to attach your hood rod on. In order to allow your hood to close without the rod interfering with the closing of your hood.This can either be obtained at your dealer or salvage yard. Then you will need a 4or 5 foot poll in order to prop your hood.So that you can place the bushing in and also hood attachment bushing.Both bushings snap right in. You will need to take your hood rod and place it in the hole of the bushing the hood rod should have a short bend at the bottom of it.Like an L or 7 the L shape should seat it self into the bushing.In order to erect the rod to hold the hood up.Or in order to attach it on the hood attachment.Before closing the hood. The hood rod bushing for extending your hood rod.In order to hold your hood up.Goes in the side of the inside frame of the body to the rear of the passenger side of the car again it just snaps in. And the hood rod attachment goes towards the front of the passenger side and it also snaps in.It's located horizontal of the headlight.The hood rod bushing is a 2 sided little round shaped plastic bushing just big enough for your hood rod to fit through.And it is usually white. And your hood rod attachmewnt is usually black.

    Jul 31, 2008 | 2001 Ford Focus

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    33 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...