Question about 1989 Mazda B-Series

2 Answers

No spark after warming

1989 mazda b2600i runs for a while then quits. No spark. after it cools a while will start. new computer, new cam sensor (j909)

Posted by on

  • 3 more comments 
  • sshamka May 08, 2009

    It has a distributor. This model year has two ignition modules, interior and exterior (of distributor). the exterior one I've seen sometimes described as an ignitor but its really a rotor (cam) sensor. Coil appears to check good but it's hard to tell because it has two sets of input leads.

  • sshamka May 08, 2009

    1989 mazda b2600i

  • Damian Lyman May 11, 2010

    What kind of mazda and what engine is in it?

  • Damian Lyman May 11, 2010

    does it have an extribitor or does it have the coil packs

  • Anonymous Mar 28, 2014

    how much fuel pressure should a 1989 mazda 2600i have

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 65 Answers

Could be the ignition control module or the ignitin coil
I had the same problem with a 91 cavelier ran til it got warm then quit
once it cooled down it woun run good again.
tried everything and it was the ignition control module

Posted on May 09, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 204 Answers

It could be your coil. if it is shorting out internally

Posted on May 08, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No spark after car gets warm


You need to hook up a scanner or code reader and see what code is stored.

Jun 12, 2013 | 2001 Daewoo Nubira

1 Answer

1989 Buick intermitent engine problem Buick Regal 3.1 V6 8th vin. T in nostart condition no fire @plugs no fuel pressure when cranking . Replaced : crank sensor ECM Ignition module ignition switch...


You did'nt say if you have had the car (Scanned) to see if the engine control Module has stored any fault codes. You say it runs 20 miles or so before it quits. After cooling does it alawys start back up? What have you been doing to get it running again? The ECM can warm up and quit. It'll get an Troblem code about though. The no spark at the time sort of removes the Cat converter overheating and the ingtion Module ( (the coils are mounted to it). Something getting too hot is likly. Crank sensers and cam sensers both wil do this the crank senser is on the back of the block just above the oil pan. The cam sewnser is underneath the power steering pump and the connector going to it is on top of the front valve cover on the passenger side. Crank sensers will not code and still be bad. Computers if they come back on ever they will code most any problem and the code name is Quad driver failure.

Jul 23, 2011 | 1989 Buick Regal

2 Answers

89 B2600I: engine starts and runs if you spray starting fluid in air intake- you quit then it quits. Injectors have 12 volts. computer has constant & ignition 12 volts plus several good ground...


So we would have to assume from what you're saying that the injectors are not being pulled to ground by the computer. Have you tried listening to them with a mechanics stethoscope? The computers are a common problem but if another one gives the same result then I'd have to say that the wiring harness between the computer and the injector is suspect. You will have to check the continuity between the injector plug and the connector that goes into the computer. You will need a wiring diagram but I think the wire colors at the injector should be the same as they enter the computer. I would strongly suggest that you confirm fuel pressure though. I know what you mean by fuel at the injectors, but pressure is important.

Jun 05, 2011 | 1989 Mazda B-Series

1 Answer

1989sunbird starts cold then shuts down electricly when warmed up


i would recheck the ignition module, sound bad to me. make sure that you test the module when hot

Apr 20, 2009 | 1989 Pontiac Sunbird

1 Answer

1989 ford aerostar will not start when engine is warm.


AM temp 55 car started but stalled out after starting. Attempted to restart and did not hear fuel pump. Tried again and then fuel pump kicked in. Checking fuel pump inertial switch and fuel pump electrical supply.

Apr 19, 2009 | 1989 Ford Aerostar Cargo

2 Answers

Car stalls while driving


you have a bad crankshaft sensor. replace the crank sensor.

dodges and gm's are known for this problem.

Apr 10, 2009 | 1998 Plymouth Neon

1 Answer

1991 Mazda truck starts, then dies unless


Not a solution but i am going through the exact same nightmare and same symptoms with my 1991 mazda b2200. I've apwnt over two grand to have my rebuilt TWICE and my alternator replaced and still does the same thing just starts only to die 2 seconds or so later unless i let it warm up to its max but will still die when taking turns and stopping at lights.

Mar 23, 2009 | 1991 Mazda B-Series

1 Answer

1989 Mazda B2600i pickup overheats. Replaced


you just said it you need a new fan clutch

Mar 20, 2009 | 1988 Mazda B2600 Cab Plus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

507 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...