Question about 2008 Mitsubishi Lancer GTS CVT Sedan

1 Answer

Blower will not come on

Replaced blower motor but still does not come on is there a resister in line

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 46 Answers

Sort of...it the control that allow the blower motor to run at different speeds. Check for voltage at the wires going into the motor...I assume you checked before replacing the motor, but check again. If voltage is there, a bad motor was installed. If no voltage, consult a Haynes Manual wiring diagram to trace the wires from the blower motor back to the source (batt). Best of luck resolving this issue.

Posted on Nov 25, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace blower motor 2005 malibu


Hey Kenny,here's a guide to replace blower motor,if blower is not working or just on certain speeds,if could be your blower motor resister,here's a link to the resistor.I would straight wire motor to see if it works,if it does then resister could be bad,have to replace to see if it is bad on the resister.Here's the part.

Jan 13, 2013 | 2005 Chevrolet Malibu Maxx

Tip

Blower motor problems


If ,and when,your blower motor has problems,and it will not blow on the low speeds, consider the blower resister,it is what controls the speeds for your blower motor.Now,replacing the blower resister is the thing to do,but two things to check for also,,the connector to the blower resister,and to the back of the fan select switch,the one you control,on the dash.These connectors,including the fan switch can be burned,and need replacing also.Now the reason these go out,and burn,and melt the connectors,is,that the blower motor is pulling too many amps,even though the blower motor runs great,and sounds good,trust me,the blower motor is the reason,so replace all of these parts when you replace the resister.If the connectors are fine,and the blower switch is fine,of course they will not need to be replaced,but the blower motor is a must,or you just might have to do it all over again in a few months,along with the switch,and connectors I mentioned.

on Jul 20, 2010 | Chevrolet C1500 Cars & Trucks

1 Answer

91 Astro Van, Heat/AC Blower not working....replaced switch, fuse, motor


well here's your fix next to the blower motor is the resister that controls the different fan speeds the resister burns out but before getting the new resister unplug the resister as the connectors over heat and at time also need replacement

Aug 12, 2012 | Cars & Trucks

2 Answers

Blower motor only runs on high


It is the blower motor resister next to the blower motor,it is what controls the speeds.It will have about 7 wires that plug into it,and it is most likely mounted with two screws,it will actually mount on the out side,but fits inside the blower box,to keep it cool,now,even though the blower motor may run quite,and smooth,it is pulling to many amps,this is what causes the resister to go out,my suggestion,is to replace the blower motor also,or you will be replacing the resister often.

Jan 16, 2010 | 2000 Oldsmobile Intrigue

2 Answers

Heater blower motor blows normal then slows down 1999 grand marquis


There is a blower resister within the blower fan that is replacable. Most likely this is the problem

Jan 04, 2010 | 1999 Mercury Grand Marquis

1 Answer

2000 Ford Taurus - A/C fan only works on high; cool air is "available" but not blown as fan won't run, except in "high" position. Any suggestions?


The low speeds(all of them) are distributed threw the fan speed switch to the blower motor resister.The resister is the problem.It is located very near the blower motor.It has two screws mounting it to the blower box.It has a plug in with about 5 to 7 wires.Unplug this plug to the resister.Remove the screws.Pull the resister toward you,it mounts and rest inside of the blower case,this is how it is cooled.Now when you replace the resister,replace the blower motor.Even if the bower motor is running fine, it is pulling to many amps for the resister.It will happen again soon,if you don`t replace the blower motor.If I can help you any more,please let me know.

Aug 31, 2009 | 2000 Ford Taurus

1 Answer

Ac blower motor will only work on high sometimes not at all.This is on a 2003 dodge caravan


replace blower resister this is ur speeds if blower at times doesnt blow at all replace blower motor this is what burn out the blower resister

Jul 01, 2009 | 2003 Dodge Caravan

3 Answers

The blower motor resistor is out on my 2004 dodge stratus.


Hi my name is Allen!

The blower motor resister is located on the passenger side under the dash, it's mounted on the bottom of the A/C Housing.

If you bought the resister from the dealership you will need to make the hole larger for the new style resister so it will fit.

You should also replace the blower motor, because the resistance built up inside the motor is what damages the resister.

For further assistance contact me at FixYa!

Dec 29, 2008 | 2003 Dodge Stratus

1 Answer

2004 dodge stratus fan motor housing


Hi my name is Allen!

The Blower Resister is located on the passenger side. You will need to remove the silencer pad below the glove box, not behind but below the glove box. The resister is located on the bottom of the A/C Housing next to the blower motor. If you get the resister from the Dealership you will need to make the hole larger that the resister fits into because it has been redesigned and is to large for the whole. Also you will want to replace the blower motor also because the resistance build up inside the motor is what damages the resister.

If you need further asistance you may contact me through FixYa!

Dec 27, 2008 | 2004 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...