Question about 1997 Jeep Grand Cherokee

Open Question

Head torque sequence

What is the torque and sequence,on a jeep head

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: What is the torque Specification& sequence for

Size motor?

Posted on Oct 26, 2009

Testimonial: "c17hydro was very helpful and responded quickly. "

  • 176 Answers

SOURCE: need to know head bolt sequence for 98' jeep

Check with your local Napa store. They should be able to print it out for you.

Posted on Oct 26, 2009

jturcotte
  • 8215 Answers

SOURCE: need to know lbs of

From autozone.com:
To install:

  1. Thoroughly clean the gasket mating surfaces. Remove all traces of old gasket material. Remove all carbon deposits from the combustion chambers. Lay a straightedge across the head and check for flatness. Total deviation should not exceed 0.001 in. (0.025mm).

The cylinder head gasket used on the 2.5L engine is a composition gasket. The gasket is to be installed dry. Do not use gasket sealing compound on the gasket.
  1. Fabricate 2 cylinder head alignment dowels from 2 used cylinder head bolts. Cut the head of the longest bolt off below the hex head. Then cut a slot in the top of the dowel to allow easier removal with a screwdriver.
  2. Install one dowel in bolt hole No. 10 and the other dowel in bolt hole No. 8.
  3. Place the cylinder head gasket over the dowels with the numbers facing up.
  4. Place the cylinder head over the dowels.
  5. Coat the threads of bolt No. 7 only, with Loctite PST sealant or equivalent.
  6. Install all head bolts except Nos. 8 and 10.
  7. Tighten the bolts in the sequence shown in the illustration to the following:
    1. Tighten bolts 1 through 10 in sequence to 22 ft. lbs. (30 Nm).
    2. Tighten bolts 1 through 10 in sequence to 45 ft. lbs. (61 Nm).
    3. Recheck bolts 1 through 10 in sequence to verify that they are 45 ft. lbs. (61 Nm).
    4. Tighten bolts 1 through 6 in sequence to 110 ft. lbs. (149 Nm).
    5. Tighten bolt 7 to 100 ft. lbs. (136 Nm).
    6. Tighten bolts 8 through 10 to 110 ft. lbs. (149 Nm).


During the final tightening sequence, bolt No. 7 will be tightened to a lower torque than the rest of the bolts. Do not overtighten bolt No. 7.
  1. Connect the temperature sending unit wire.
  2. Install the spark plugs.
  3. Install the compressor.
  4. Install the compressor/alternator bracket mounting bolt.
  5. Adjust the alternator drive belt.
  6. Install the air conditioning compressor drive belt.
  7. Install the intake and exhaust manifolds.
  8. Install the power steering pump bracket.
  9. Install the pushrods. Keep them in order!
  10. Install the rocker arms. Keep them in order!
  11. Thoroughly clean the mating surfaces of the head and rocker cover and install as outlined earlier in this section.
  12. Install the air cleaner.
  13. Connect the hoses at the thermostat housing.
  14. Connect the battery ground.
  15. Fill the cooling system.
  16. 1a34825.gif

Posted on Sep 23, 2010

chuckster57
  • 1102 Answers

SOURCE: what is the head bolt toqure sequence for a 1990

Here is a picture of the torque procedure.
Bolt #11 threads must be coated with loctite 592 sealant before installation

Tighten all bolts in order to 22 Ft/Lbs.
Tighten all bolts in order to 45 Ft/Lbs
ReTighten all bolts in order to 45 Ft/Lbs
Tighten bolts 1-10 in order to 110 Ft/Lbs
Tighten bolt 11 to 100 Ft/Lbs
Tighten bolts 12-14 to 110 Ft/Lbs


chuckster57_4.gif

Posted on Dec 28, 2010

ZJLimited
  • 17970 Answers

SOURCE: i am looking for the

zjlimited_950.jpg

Fig. 17: Cylinder head bolt torque sequence (click over pic for zoom)


Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

Tighten all bolts to 22 ft. lbs. (30 Nm).
Tighten all bolts to 45 ft. lbs. (61 Nm).
Retighten all bolts to 45 ft. lbs. (61 Nm).
Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
Tighten bolt 11 to 100 ft. lbs. (136 Nm)
Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)




Hope this helps (remember to rate and comment this answer).

Posted on Mar 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

1 Answer

Need torque specs foe a 2000 jeep with a 4.0 to be spacific i need the mains rods and head


Hello mooredavid42,

The Head bolt torque is as follows:

1. Tighten all bolt in the sequence shown in the image below to 22 ft. lbs.
2. Tighten all bolt in the sequence shown in the image below to 45 ft. lbs.
3. Check all bolt to verify they are torqued to 45 ft.lbs in the sequence shown below.
4. Tighten bolts in sequence:
a. Bolts 1-10 to 110 ft.lbs.
b. Bolt 11 to 100 ft. lbs.
c. Bolts 12-14 to 110 ft.lbs.

If you are reusing the head bolts carefully check the bolts for necked down threads.

netvan_199.png

The main bearing cap bolts are torqued to 80 ft. lbs.

The connecting rod nuts are torqued to 33 ft. lbs.

I hope this helps.

Regards,

Jerry

Aug 24, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Head bolt sequence and tourqe for 99 jeep 4.0 motor


  1. CAUTION
  2. During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

  3. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
  4. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
  5. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
  6. Tighten bolts in sequence:
  7. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
  8. Bolt 11 to 100 ft. lbs. (135 Nm).
  9. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
  10. Check all bolts in sequence to verify the correct torque.


ledsled378_134.jpg

Jul 02, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

I am looking for the head bolt torque specifications and sequence for a 1988 jeep Cherokee 4.0 i6


zjlimited_950.jpg

Fig. 17: Cylinder head bolt torque sequence (click over pic for zoom)


Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

Tighten all bolts to 22 ft. lbs. (30 Nm).
Tighten all bolts to 45 ft. lbs. (61 Nm).
Retighten all bolts to 45 ft. lbs. (61 Nm).
Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
Tighten bolt 11 to 100 ft. lbs. (136 Nm)
Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)




Hope this helps (remember to rate and comment this answer).

Mar 30, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Lookin for head torque specs and sequence


Torque sequence ----------- ' 9 7 3 1 5 ' ' 8 4 2 6 ' ----------- Step 1: torque in sequence to 45 Ft/Lbs Step 2: torque in sequence to 65 Ft/Lbs Step 3: torque in sequence to 65 Ft/Lbs again plus 1/4 turn Step 4: Torque small bolt in rear of head to 25 Ft/Lb Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
3.3L

Feb 07, 2011 | 1996 Dodge Grand Caravan

1 Answer

What is the head bolt torque specs on a 1990 jeep 4.0


  1. Tighten all bolts in sequence (1 through 14) to 30 N·m (22 ft. lbs.) torque.
  2. Tighten all bolts in sequence (1 through 14) to 61 N·m (45 ft. lbs.) torque.
  3. Check all bolts to verify they are set to 61 N·m (45 ft. lbs.) torque.
    1. Tighten bolts in sequence:
    2. Bolts 1 through 10 to 149 N·m (110 ft. lbs.) torque.
    • Bolt 11 to 135 N·m (100 ft. lbs.) torque.
    • Bolts 12 through 14 to 149 N·m (110 ft. lbs.) torque
  • 900c8cad.gif

    Dec 16, 2010 | 1990 Jeep Cherokee Limited

    1 Answer

    Head bolt tighting sequance for a jeep 4.0


    CAUTION: During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT overtighten bolt No.11.

    • Tighten all bolts in sequence (1 through 14) to 30 Nm (22 ft. lbs.) torque.
    • Tighten all bolts in sequence (1 through 14) to 61 Nm (45 ft. lbs.) torque.
    • Check all bolts to verify they are set to 61 Nm (45 ft. lbs.) torque.
    • Tighten bolts in sequence:
    • Bolts l through 10 to 149 Nm (110 ft. lbs.) torque.
    • Bolt 11 to 13 Nm (100 ft. lbs.) torque.
    • Bolts 12 through 14 to 149 Nm (110 ft. lbs.) .
    • 21e690f.gif

    Apr 21, 2010 | 1998 Jeep Cherokee

    1 Answer

    What is the cylinder head torque on a 2001 jeep cherokee


    Please don't forget to rate....thanks:


    e1aba13.gif

    1. Tighten the engine cylinder head bolts in sequence according to the following procedure

      CAUTION During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT over tighten bolt No.11.

    2. Tighten all bolts in sequence (1 through 14) to 22 ft. lbs. (30 Nm).
    3. Tighten all bolts in sequence (1 through 14) to 45 ft. lbs. (61 Nm).
    4. Check all bolts to verify they are set to 45 ft. lbs. (61 Nm).
    5. Tighten bolts in sequence:
    6. Bolts 1 through 10 to 110 ft. lbs. (149 Nm).
    7. Bolt 11 to 100 ft. lbs. (135 Nm).
    8. Bolts 12 through 14 to 110 ft. lbs. (149 Nm).
    9. Check all bolts in sequence to verify the correct torque.

    Mar 06, 2010 | 2001 Jeep Cherokee

    1 Answer

    What is the torque setting for a 2.4 4cyclinder jeep engine


    Head needs to be "step torqued" first round is at 22 foot pounds, second is at 45 foot pounds, third is 100 foot pounds at passenger side front corner, 100 at all others. sequence is: passenger side: front to rear: 8,4,1,5,9
    Drivers side: 7,3,2,6,10 Tighten in numerical order (1,2,3,4, etc).

    Sep 22, 2009 | 1991 Jeep Wrangler

    1 Answer

    1991 jeep cherokee sport 4.0


     For your 1991 Jeep Cherokee 2WD 4.0L MFI :
      Foot pounds (Final torque) 

      Note:
      Torque sequence ------------------  
      front    | 12  8   4   1   5   9  13 | 
      of | | 
      engine | 11  7   3   2   6   10 14 | 
      ------------------  
    Final torque must be reached in 3 equal steps  
      Step 1: torque all bolts (except bolt 11)  
      to 110 Ft/Lbs  
      Step 2: torque bolt 11 to 100 Ft/Lbs  
    Recheck final torque in sequence  

    Sep 30, 2008 | 1991 Jeep Cherokee Briarwood

    Not finding what you are looking for?
    1997 Jeep Grand Cherokee Logo

    Related Topics:

    31 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...