Question about 2011 Ford Edge

Open Question

2008 ford edge blend door motor actuator removal

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 13 Answers

SOURCE: trying to remove dashboard to access blend door actuator and

www.heatertreater.net

Posted on Jan 04, 2009

Ad
harley9701ha
  • 424 Answers

SOURCE: cant find the blend door actuator on 2003 ford f150 super crew

The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Posted on Jun 22, 2009

oldfishead
  • 155 Answers

SOURCE: new blend door actuator doesnt operate

had this problem before... recheck part#....is it for EATC or MANUAL...??? eatc on a manual will only go to half way...sounds like they gave you the wrong part....its a pain to replace wasn't it.....hope this helped you...GL

Posted on Jul 06, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

bunnydawg
  • 5158 Answers

SOURCE: 2002 Ford Crown Vic 4.6L. EATCM A/C, Heating

that clicking noise you hear is likely a relay in the fuse panel that needs to be replaced. the easiest way to find out which relay it is would be to put you finger on each relay as you actuate the device not working. once you locate the clicking relay replace it . to reset the computer just unhook the battery for about ten minutes. if you have an anti theft radio make sure you know the code for it and how to enter it before you unhook the battery.

robert

Posted on Nov 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

"Relearning" process for re-installation of blend door actuator motor (if necessary) on 1997 Ford F150.


There is no process, just make sure the battery negative cable is disconnected before install the part.

Apr 19, 2017 | Ford Cars & Trucks

1 Answer

Removing blend door actuator on 2008 kia sedona


Removal of this device is achieved by removing the interior door panel at the door which is affected. Remove arm rest and handles pull edges of door panel gently to release plastic snaps holding the door panel around its edges. If you know an upholstery shop, they can instruct you about removing door panels. Its involved job.

Oct 24, 2016 | 2008 Kia Sedona

1 Answer

2008 ford rangerhave vacuum but no heat


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Nov 09, 2012 | 1996 Ford Ranger SuperCab

1 Answer

2008 ranger blend door not working


It can be a jamming door has damaged the actuator motor, both problems are common on this truck. You can buy a kit on line that is called a "HEATERTREATER" THAT ALLOWS YOU TO REPLACE THE BLEND DOOR WITHOUT REMOVING THE DASH, EBAY ALSO HAS THE KITS.

Sep 06, 2012 | Cars & Trucks

5 Answers

My 1997 ford f150 heater will not blow hot air. i have replace the switch that controls the hot and cold air. i do not know what else to do. i do not heat any vacuum noise when i switch it to the heater or...


first, check under te hood to see if the heater core water hoses are hot going in and coming out. If hot going in but cold coming out, water valve (if you have one) may not be working.
------------------------------------------------------------------------------------------------
Control System Outputs
The air management doors are controlled by vacuum control motors (18A318) and an A/C electronic door actuator motor (19E616). The air inlet and distribution doors are controlled by vacuum control motors. The temperature blend door is controlled by the A/C electronic door actuator motor.
The A/C electronic door actuator motor provides a variable number of temperature blend door positions. Temperature control position energizes the A/C electronic door actuator motor moving the temperature blend door.
Vacuum control motors are used on both air distribution and air inlet doors. The air inlet and panel/defrost doors use a two position vacuum control motor. The floor duct/panel door uses a three position vacuum control motor. Vacuum control motors are controlled by engine vacuum through the climate control head.
For more information on the control components Section 412-04 .
-------------------------------------------------------------------------------------------------------------------------------------
Air Management Doors
The air management doors are controlled by vacuum control motors (18A318) and an A/C electronic door actuator motor (19E616). The air inlet and distribution doors are controlled by a vacuum control motor. The temperature blend door is controlled by the A/C electronic door actuator motor.
The A/C electronic door actuator motor provides a variable number of temperature blend door positions. Temperature control position energizes the A/C electronic door actuator motor moving the temperature blend door.
Vacuum control motors are used on both air distribution and air inlet doors. The air inlet and panel/defrost doors use a two position vacuum control motor. The floor duct/panel door uses a three position vacuum control motor. Vacuum control motors are controlled by engine vacuum through the climate control head.
-------------------------------------------------------------------------------------------------------------------
Section 412-04: Control Components - Climate Control 1997 F-150, F-250 Workshop Manual
REMOVAL AND INSTALLATION A/C Electronic Actuator
Removal
  1. Remove the floor duct panel.
    • Remove the two plastic push pins (one each side) and release the expander clip.
  1. Remove the RH instrument panel brace.
    1. Remove the lower nut.
    1. Remove the upper bolt.
    1. Remove the brace.
  1. Remove the LH instrument panel lower nut and position brace out of the way.
  1. Disconnect the vacuum harness from the vacuum actuator.
  1. Remove the floor duct.
    1. Remove the two screws (one each side).
    1. Remove the floor duct.
  1. Remove the panel/floor door vacuum control motor.
    1. Disconnect the vacuum line connector.
    1. Remove the two panel/floor door vacuum control motor screws.
    1. Slide the rod out of the door and remove the panel/floor door vacuum control motor.
  1. Remove the electronic actuator.
    1. Disconnect the electrical connector.
    1. Remove the three screws.
    1. Pull down to release the actuator shaft and remove the electronic actuator.

Jan 24, 2011 | 1997 Ford F150 Regular Cab

2 Answers

2004 f350 ford heater blows cool air but hoses are both warm-where do i start looking


check to see if the blend door is moving where you change the temperature setting. I think your blend door is behind the glove box. Here are instructions for removing the actuator. Take it off, plug it back in and see if the motor rotates. Also check to see if you can rotate the blend door by hand. If you can rotate it by hand, the motor is probably broken of the gears are stripped. Let me know if you have questions.
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
f4b0b74.gif Fig. Blend door actuator-F-250 & 350


  1. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  2. To install, reverse the removal procedure.

Oct 17, 2010 | 2004 Ford F350

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

2 Answers

A/c temp on max 27 a/c temp on norm 50?


Was browsing the ford f-150 forum and found that Ford has a lot of issues with it's AC, some too hot and some like yours, way to cold. At MAX it should read around 42. Best 2 solutions I've found are:
  • Blend door/Blend door motor
  • Dirty EVAP coil
Here's a pic of what the Blend door/Motor look like and instructions on how to replace it. Wish you the best of luck.

Removal & Installation
  1. Release the stops and lower the glove compartment door.
  2. Disconnect the connector.
  3. Remove the two screws. Rotate the blend door actuator and bracket assembly. Remove the electronic blend door actuator and bracket assembly.
  4. To install, reverse the removal procedure.



b23881e.jpg

May 09, 2009 | 2002 Ford F250 Super Duty SuperCab

2 Answers

Need to replace ac blend door motor inside dashby glove box does dash have to come out and how much trouble is it?


the bummer is removing instrument panel. big job.

A/C Electronic Blend Door Actuator Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove instrument panel (04320). Refer to Section 01-12 .
  1. Remove four A/C electronic blend door actuator retaining screws.
  1. Remove A/C electronic blend door actuator.


2c01b1e.gif
Item Part Number Description 1 18471 Heater Air Plenum Chamber 2 42141-S8 Screw (4 Req'd) 3 — A/C Electronic Blend Door Actuator 4 — A/C Air Temperature Control Door Shaft (Part of 18471) 5 19D842 A/C Air Temperature Control Door

Feb 23, 2009 | 1997 Lincoln Town Car

Not finding what you are looking for?
2011 Ford Edge Logo

Related Topics:

764 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...