Question about 1990 Ford F150

Open Question

Ignition control module 1994 ford club wagon 5.8L location?

Is the ICM black or gray?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1996 ford thunderbird ignition control module

near the firewall behind intake manifold

Posted on Aug 18, 2008

  • 1 Answer

SOURCE: ignition control module location for 1997 ford thunderbird?

1997 Ford Thunderbird Transmission problem
When driving normally transmission surges like it is not in gear. Had sensors replaced, nitural safety switch, and still acts up.

Posted on Dec 18, 2008

frankzen
  • 19 Answers

SOURCE: Where is the Ignition Control module located on a 1990 Ford f150

The ignition module is held on to the distributor by two 5.5mm bolts, but there is a tool for getting those bolts out. And you're right they are prone to failure.

Posted on Apr 04, 2009

chuck943
  • 783 Answers

SOURCE: where is the ignition module control located on 1996 ranger 2.3 e

It does not have an ignition control module. The PCM (powertrain control module) fires the coil pack based on signal it recieves from the crankshaft position sensor and the camshaft position sensor.

Posted on Apr 08, 2009

  • 33 Answers

SOURCE: locate ignition control module on 94 ford taurus

It is mounted on the side of the distributor on the right side of the motor as you are facing it.

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1006 ford ranger ignition cotrol module location


Your ranger doesn't have a ICM - ignition control module . PCM - engine computer controls spark .

Jan 16, 2017 | Ford Ranger Cars & Trucks

1 Answer

Where is the icm on a 1994 toyota tercel?


The ICM is small usually cylindrical, typically located on the outside of the distributor. There will be two wires attached to it.

Dec 17, 2014 | 1994 Toyota Tercel

1 Answer

Where is ignition control module located on 1998 ford Taurus se


The ICM is located at the rear of the Throttle control body. Look for where your plastic hose from your air breather connects to the engine at. Remove the plastic hose at the engine and at the rear of the round metal part the you removed the hose from, closest to the firewall or the back side will be the ICM

Oct 03, 2014 | 1998 Ford Taurus SE

1 Answer

99 mercury mystique icm location 4cyl.


The ignition control module on your car is located right on top of the engine. Follow your spark plug wires up to where they all plug in to a small black box often referred to as the ignition coil. Thats it. The ignition control module is integrated into the coil on this car. Hope this helped.

Aug 15, 2012 | 1999 Mercury Mystique

2 Answers

Locate the ICM on a 95 bronco 5.8L (ignition control module)


On 1995 Ford Truck Bronco 5.8L EFI 8cyl the Control Module-Ignition is located under hood, center, upper engine area, front of intake manifold, mounted on front side of distributor.

zjlimited_1625.jpg

Fig. 1: A TFI-IV ignition module



Hope this helps (remember to rate and comment this free answer).

Jul 26, 2011 | 1993 Ford Bronco

1 Answer

I can not locate my icm for a '96 ford 4.6. i have police inc. i have foiund the cruz control mod. is the icm inside the comp? ron


1996 Ford Crown Victoria 4.6L SFI 8cyl the Control Module-Ignition is located: Under hood, driver side, upper engine area, mounted on rear of fenderwell.

Hope helps (remember rated and comment this).

Sep 03, 2010 | 1996 Ford Crown Victoria

1 Answer

I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Jul 27, 2010 | 1993 Ford Ranger SuperCab

1 Answer

1996 FORD EXPLORER , MISS FIRE ON CYL # 2, 1ST REPLACED PLUGS AND WIRES, THEN THE COIL PACK AND LAST THE FUEL INJECTOR BUT PROBLEM STILL THERE, ANY HELP WOULD BE GREAT


OK,
Have you tried the following:


Ignition Control Module (ICM) REMOVAL & INSTALLATION NOTE: Only the EEC-IV ignition systems use an external ICM. EEC-V systems have incorperated the ICM into the Power Control Module (PCM).
  1. Disconnect the negative battery cable.
  2. Detach the wiring harness connector(s) from the ICM.
  3. Remove the mounting bolts, then remove the ICM. To install:
  4. Position the ICM onto the inner fender apron and install the mounting bolts. Tighten the bolts to 22–31 inch lbs (2.5–3.5 Nm).
  5. Attach the wiring harness connector(s) to the ICM.
  6. Connect the negative battery cable. Fig. 1: Ignition control module and mounting location on the 2.3L, 2.5L engine 89682g32.gif
    Fig. 2: Ignition control module used on all EEC-IV systems except the 2.3L engine 89682g33.gif
    Fig. 3: Ignition control module mounting on all EEC-IV systems except the 2.3L engine 89682g34.gif
prev.gif next.gif

Jul 11, 2010 | 1996 Ford Explorer

1 Answer

How do you remove the ignition coil


Each ignition control module (ICM) has the following circuits:
An ignition 1 voltage circuit A chassis ground An ignition control circuit for each cylinder A low reference circuit
The PCM controls spark by pulsing the ignition control circuits to the ICM to trigger the coils and fire the spark plugs. The PCM and ICM are internally protected against shorts to power and ground on the ignition control circuits.

The spark plugs are connected to each coil by a short boot. The boot contains a spring that conducts the spark energy from the coil to the spark plug. The spark plugs are tipped with platinum for long wear and higher efficiency.


Ignition Control Module (ICM) Connectors

248af41.jpg

Fig. Ignition coil locations 2001-2004 4.8L, 5.3L, 6.0L Engines



Removal & Installation
2.2L (L61) Engine
  1. Turn OFF the ignition.
  2. Remove the accelerator cable from the bracket.
  3. Remove the accelerator cable bracket bolt.
  4. Remove the accelerator cable bracket.
  5. Disconnect the ignition control module (ICM) harness connector.
  6. Remove the ICM retaining screws.
  7. Remove the ICM from the ignition coil housing.

To install:
  1. Install the ignition control module in the ignition coil housing.
  2. Install the ICM retaining screws. Tighten the retaining screws.
  3. Connect the ICM harness connector.
  4. Install the accelerator cable bracket.
  5. Install the accelerator cable bracket bolt. Tighten the retaining screws.
  6. Install the accelerator cable to the bracket.

2.2L (Ln2) Engine
  1. Remove the air cleaner outlet from the air cleaner.
  2. Remove the ICM electrical connectors (1) and spark plug wires (2).
  3. Remove the ignition coils bolts (3).
  4. Remove the ignition coils and ICM assembly.
  5. Installation is the reverse of the removal procedure.

2.4L Engine
  1. Disconnect the negative battery cable.
  2. Remove the accelerator cable from the hold down clip.
  3. Remove the cruise control cable, if applicable.
  4. Remove the bolt from the fuel line retaining clip.
  5. Disconnect the 11-pin harness connector for the ignition control module (ICM).
  6. Remove the bolts from the ignition coil and the ICM assembly-to-camshaft housing.
  7. Remove the ignition coil and ICM assembly from the engine.
  8. Remove the screws that retain the housing to the cover.
  9. Disconnect the coil harness connector from the ICM.
    CAUTION When removing the housing from the cover, make sure the ground strap stays in place.
  10. Remove the housing from the cover.
  11. Remove the screws that retain the ICM to the cover.
  12. Remove the ICM from the cover.

    9f8592c.jpg
    Fig. Removing the ICM from the camshaft cover

To install:

CAUTION DO NOT wipe grease from the module or coil if the same module is to be replaced. If a new module is to be installed, a package of silicone grease will be included with the module. Spread the grease on the metal face of the module and on the cover where the module seats. This grease is necessary for module cooling.
  1. Install the ICM to the cover.
  2. Install the screws that retain the ICM to the cover.
  3. Install the ground strap, if necessary.
  4. Connect the ignition coils connector to the ICM.
    CAUTION When installing the housing to the cover, make sure the ground strap stays in place.
  5. Install the housing to the cover.
  6. Install the screws that retain the housing to the cover.
  7. Install the spark plug boots and the retainers to the housing, if necessary.
  8. Install the ICM assembly to the engine while carefully aligning the spark boots to the spark plug terminals.
    CAUTION The ICM cover bolts must be installed using isolator washers with the rubber side facing down.
  9. Install the bolts that retain the ICM assembly to the camshaft housing after coating the bolt threads with LOCTITE, or equivalent. Tighten the bolts to 16 ft. lbs. (22 Nm).
  10. Connect the ICM 11 pin harness connector.
  11. Install the bolt to the fuel line retainer clip.
  12. Install the accelerator cable into the hold down clip.
  13. Install the cruise control cable, if applicable. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 05, 2010 | 2000 Chevrolet Blazer

4 Answers

How to fix obd code p1351 on 1996 ford bronco


P1351 Ignition Diagnostic Monitor circuit Input fault
The code 1351 in most case is set when the Ignition moduel has been replace with the gray one and it calls for the Black one.
The ICM for this vehicle should be Black in color instead of Grey. Ford parts books are incorrect and show that this vehicle should have a Grey module. The Motorcraft part number for the Black ICM is a DY-679
Good luck and make sure you use the OEM part.


Dec 26, 2009 | 1996 Ford F250 Crew Cab

Not finding what you are looking for?
1990 Ford F150 Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...