Question about 2001 Nissan Pathfinder

Open Question

How to remove cowl cover on 2004 nissan pathfinder

To get to windshield wiper linkage

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 97 nissan sentra windshield wiper linkage arm disconnected

Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Posted on Sep 14, 2008

  • 2 Answers

SOURCE: Wiper Linkage

if you live near montreal you got yasmine auto at laval they got mostly part of qx4 but it fit for pathfinder if they dont got it usely they can tell you where

Posted on Mar 03, 2009

  • 1 Answer

SOURCE: How do I access the windshield wiper assembly?

You have to remove the wiper arms by prying off the black platic piece over the nut. Remove the nut and the wiper arms. There should be 5 places on the black plastic piece that runs the length of the windshield. Remove 4 of them by prying them out. The one is the middle is a screw. Pull away the plastic piece and you should have access to the mechanism below. I think you need to replace the linkage if it has fallen off.

Posted on Oct 14, 2009

  • 1 Answer

SOURCE: trying to find out the fuse for windshield wipers

where is fuse located for windshield wipers on 2004 altima?

Posted on Feb 16, 2010

  • 3741 Answers

SOURCE: Need to know how to

The wiper cam actuator the cam is made to prevent damage to the motor by using a spring to allow it to slip if the wipers are stuck or frozen to the wind shield the spring stretching causes the wipers to stop in the middle of the window not hard to replace but does require you to do a timing procedure it should come in the box if not ill give you the basics get the new part remove both wiper arms careful the windshield is under the black plastic and I've seen other break the windshield taking the wiper arms off a battery post puller is the best way to remove , remove the cowl plastic piece you will see the cam gold/silver in color remove the one torx head screw then install new one rotate clockwise 2 times should spin freely then spin counter clockwise should stop look at where it is touching this area should have a 4mm gap the wiper motor has to be in the intermittent position prior to this turn key on put wipers in intermittent let motor spin then when it stops shut the key off then install cam.
--------
Removal Procedure:Tools Required:J 39232 Wiper Linkage Separator
Remove the wiper arms. Refer to Windshield Wiper Arm Replacement .
Remove the air inlet grille panel. Refer to Air Inlet Grille Panel Replacement .
Remove the water shield.Remove the screw and the nut.

Dissconnect the RH linkage assembly from the LH linkage assembly with the J 39232 .
Remove the LH linkage assembly.Remove the screw from the wiper motor.

Pull the wiper motor free from the slots of the bracket.Disconnect the RH linkage assembly from the wiper motor with the J 39232 .Disconnect the electrical connector from the wiper motor.
Installation Procedure:Tools Required:J 39529 Wiper Linkage Installer

Connect the electrical connector to the wiper motor.Connect the RH linkage assembly to the wiper motor with the J 39529 .
Important: When installing the wiper motor, be sure that the crank arm is in the innerwipe position. The crank arm drive pin must be engaged in the cam pocket.
Install the wiper motor with two locator pads pressed into the slots of the bracket.
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
for getting more help on this issue please click on the link directly
http://www.adriatic-company.it/matizclub/tecnica/manualeII/M39d%20Wipers%20-%20Washer%20Systems.pdf
This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Posted on Mar 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Wiper motor


Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

Feb 13, 2016 | 2008 Chevrolet Impala

1 Answer

Broken Windshield wipers


Probably bad end on linkage. Remove wiper blades, then cowl covers, then unbolt entire linkage from motor and cowl to remove it. Inspect and repair or replace.

Jan 09, 2016 | 2003 Chevrolet Chevrolet Monte Carlo SS

1 Answer

How to replace the wiper motor on a 1994 volkswagon golf


The wiper motor on a Volkswagen is an electric motor connected through a drive linkage to the wiper arms. Windshield wipers are an integral feature for operating a motor vehicle safely. If your wipers are not functioning, or seem to lack the speed or power they used to have, the wiper motor should be removed and replaced immediately
.


Location
  • The wiper motor on a Volkswagen is located directly underneath the plastic cowl cover. The cowl cover is located directly below the windshield.

Removal
  • Begin by removing the wiper arms by prying off the covers at the base of the arms and removing the nuts that secure the arms to the drive shafts. Label the passenger and driver arms so they can be installed in the same positions. They are not interchangeable. Remove the rubber hood to cowl weather seal. Unscrew the plastic fasteners from the driver's side of the cowl cover, then remove this half of the cover. Remove the fasteners from the passenger's side cowl cover and remove this half of the cover. Disconnect the windshield wiper motor wiring harness by separating the plastic wiring connector. Remove the three bolts that secure the wiper motor to the vehicle's body. Pull the motor slightly away from the body, then remove the nut that connects the motor shaft to wiper linkage. Remove the motor.

Installation
  • Place the new wiper motor into position in the cowl and reconnect it to the wiper arm linkage. Then reinstall the three retaining bolts. Reconnect the plastic wiring connector to the wiper motor wiring harness. Place the cowl covers into position below the windshield and reinstall the plastic fasteners that retain them. Reinstall the rubber hood to the cowl weather seal. Reinstall the wiper arms in the same position you removed them from, along with the wiper arm retaining nuts and lower wiper arm covers. Turn the windshield wipers on and test for proper operation. If the wiper blades slap against the bodywork surrounding the windshield, loosen the nuts that connect the wiper arms to the shafts and adjust.

More Read: OBD2 car diagnostic tool

Aug 06, 2012 | 1994 Volkswagen Golf

1 Answer

Windshield wiper problems...can hear wine of the motor, yet arms will not move in any position.


remove plastic cowl that covers your wiper motor ( runs fom one side of car to the other under windshield ) and make sure that the linkage is not broken. broken linkage is a common issue on this car. if it is broken let me know, i can get you some instructions on a cheap diy fix insted of spending $120 - $200 on replacement parts.

Nov 07, 2011 | 2004 Saturn ION

2 Answers

How do I dismantle and reinstall a front wiper motor on a 2000 Kia Sportage?


moz-screenshot-6.pngmoz-screenshot-7.pngplay0027.gif
Wiper Motor

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the wiper motor electrical connector.
  3. Remove the four mounting bolts securing the motor to the firewall.
  4. Using a suitable prybar, carefully separate the wiper motor from the wiper linkage and remove the motor.

To install:
  1. Attach the wiper motor ball joint to the wiper linkage.
  2. Position the motor on the firewall and secure the motor with the four mounting bolts. Tighten the mounting bolts to 75 ft. lbs. (102 Nm).
  3. Connect the electrical connector.
  4. Connect the negative battery cable.play0027_0.gif

moz-screenshot-8.png

Nov 25, 2010 | 2000 Kia Sportage

1 Answer

Where is the wiper motor on my 1999 GMC Yukon?


Windshield Wiper Motor
Removal & Installation
To Remove:


  1. Remove wiper arms.
  2. Remove weatherstrip from cowl.
  3. Remove two cowl vent grille panel screws.
  4. Remove windshield nozzles and hoses.
  5. Remove three cowl vent grille panels.
  6. Disconnect windshield wiper motor electrical connector.
    NOTE: Do not remove crank arm from windshield wiper motor.

  7. Loosen nuts that attach the drive link brackets to the crank arm.
  8. Remove wiper motor crank arm brackets.






    gm-06-00-1079.gif



  9. Remove three bolts and windshield wiper motor from vehicle.

To Install:


  1. Install windshield wiper motor and three bolts.

    • Torque to: 62 in lbs. (7 Nm)

  2. With right side linkage closest to the windshield wiper motor, install drive
    link brackets to wiper motor crank arm.

    • Torque nuts to: 44 in lbs. (5 Nm)

  3. Connect electrical connector.
  4. Install nozzles and windshield washer hoses to cowl vent grille.
  5. Install three cowl vent grille panels and screws to vehicle.
  6. Install weatherstrip to cowl.
  7. Install wiper arms.


prev.gif next.gif

Oct 30, 2010 | 1999 GMC Yukon

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

1 Answer

My 1991 nissan pathfinder's wiper motor repair


The cowl panel has to be removed. You will find plastic clips and possibly a few screws holding the panel on. Once you remove the panel you will see the wiper linkage and motor.

Contact us at www.nissanpartsnow.com and we can e-mail an image to you. Thanks

Jan 20, 2010 | 1991 Nissan Pathfinder

1 Answer

ROVER MGF.REMOVING WIPER MECHANISM.


Pivot Shafts and Linkage
The windshield wiper assembly is mounted below cowl top extension (021A36) . Linkages are connected with non-removable plastic ball joints. Windshield wiper mounting arm and pivot shafts are an integral part of the windshield wiper and are serviced as one unit. Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove antenna mast from the antenna base.
  1. Remove cap on LH and RH windshield wiper pivot arms to expose nuts retaining the arms to pivot shafts.
  1. Remove two nuts, one from each of windshield wiper pivot arms . Lift wiper arms to service position, carefully rocking them back and forth to loosen them from the pivot shaft. Lift off windshield wiper pivot arms .
  1. Remove seven screws retaining the cowl top vent panel.
  1. Disconnect windshield washer hose (17A605) at LH side of vehicle just ahead of where it enters cowl top.
  1. Remove hood cowl seal.
  1. Carefully remove cowl top vent panel from vehicle.
  1. Remove three retaining screws to cowl drain tube that is connected to top cowl.
  1. Disconnect wiring harness leading to windshield wiper motor.
  1. Remove five screws retaining cowl top to vehicle and remove cowl top and windshield wiper from vehicle.
  1. Remove two screws and two nuts retaining windshield wiper to cowl top and separate the two parts.
  1. Remove drive linkage from motor shaft linkage.
  1. Remove remaining screws attaching windshield wiper and separate the two parts.
1086bde.gif

Item Part Number Description 1 02010 Cowl Top Panel 2 N621906-S2 Nut (2 Req'd) 3 17508 Windshield Wiper Motor 4 N805605-S36 Screw (2 Req'd) 5 17500 Windshield Wiper Assembly A — Tighten to 9-12 Nm (80-106 Lb-In)

Feb 23, 2009 | 1998 Ford Windstar

1 Answer

1998 f150 ford wipe linkage


I had a similar problem the plastic in front of the windshield is the cowl. to remove it I had to pop plastic cover over nuts holding wiper arms. remove them then remove all the screws and two plastic pop retainers and a rubber strip and a number of slide on clips to remove the two piece cowl then remove the electrical plug on the motor and three hex head screws holding the assembly in place (if you extend the linkage toward passenger side it will be easier to remove the assembly) you can get
replacement bushings on line at www.rockauto.com I couldn't find them locally here but did find them
on line . the ones I got are wiper linkage bushings help part no 49451 they are difficult to remove so I cut the worn ones off then used a proper sized socket and c clamp to install the new ones
bigbobpa

Jan 09, 2009 | 1998 Ford F150 Regular Cab

Not finding what you are looking for?
2001 Nissan Pathfinder Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...