Question about 2008 Nissan Quest

Open Question

2008 nissan quest high mounted stop light bulb replace

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: 1999 nissan quest brake pad replacement

Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Posted on Jan 21, 2009

  • 840 Answers

SOURCE: replacing belts after replacing water pump on 1996 nissan quest x

the easist way is to loosen the alternator slide the alternator down then slide the belt where it should go then pull up on the alternator again and bolt up Please rate my response thank you very much

Posted on Jan 30, 2009

A3sthetix
  • 41 Answers

SOURCE: How do I change brake light bulb of Nissan Sentra 2008

Was able to complete this job successfully:
It's a little tricky to do without pictures, but I don't have any available right now.

  1. Access the trunk
  2. Remove the material covering the light. You'll need to remove the black pegs by lifting the centre part. A flathead screw-driver will help. There are 2 to remove -- one directly behind the brake light and another at the top of the trunk.
  3. Pull back the material to expose the brake light wiring and the metal frame of the car.
  4. There are 2 nuts / screws to remove near the entrance of the trunk. Both are about 4 inches apart and hold the tail light's cover in place. Remove both.
  5. Using a bit of force, you will be able to pull off the entire tail light from the frame of the car. This is done on the exterior of the car.
  6. Rotate the problematic light from it's housing (it should come off with ease) and pull it out of the socket. Brake light and indicator are a 3057K bulb.

Posted on Jun 22, 2009

  • 14 Answers

SOURCE: vdc light and brake lights comes ON.

does the master cylinder have enough brake fluid in it, low fluid level commonly causes those two lights to come on you may wanna check your brake fluid level.

Posted on Oct 07, 2009

yegarboy
  • 286 Answers

SOURCE: replace 2004 nissan quest motor mounts

Get a piece of 2x4 and a floor jack. Support the bottom of the engine with the 2x4 under the oil pan. Slightly raise the jack untill slight tension is felt. Loosen the top motor mout bolts and remove the mount. Install the new mount lower the jack and retighten the mount. Do the same for the rear or bottom mounts witch ever applies. HTH

Posted on Dec 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Nissan Quest Reverse Park aid stoped working. First sound got funny and then quit. The switch disable light stays on and won't turn back on


replace the beeper that makes the sound when you are in reverse.the light will also go out after you replace thet beeper.

Sep 16, 2012 | 2008 Nissan Quest

1 Answer

How do you replace a bulb for the high mount stop light


every car i ever had always had light bulb replacement explained in the owners manual, even the high stop lights. buy a used manual on eBay and read it.

Jan 21, 2011 | 2004 Nissan Quest

2 Answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata


High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif

Oct 12, 2010 | 2006 Hyundai Sonata

1 Answer

04 nissan quest. left brake light out, replaced bulb, still no good. Any suggestions?


could be a fuse or wires or wireing harness find out if the replacement bulb is ok or if theres any damage to the wires good luck

Oct 10, 2010 | 2004 Nissan Quest

1 Answer

Tail lights on 1999 Nissan Quest will not go off when I stop the vehicle and turn the engine off. Only way to get them to go off is to remove the fuse.


is it the tqail lmaps or stop lamp bulbs on?
If stop lamp bulbs, repalce the stop lamp switch on the brake pedal

Apr 06, 2010 | 1999 Nissan Quest

1 Answer

High mount light replacement


It should have screws in the lens on the outside, or either if the lens is behind the glass, there should be a cover to remove inside the car. Either way, once either is removed the bulb is easily replaced.

Apr 03, 2010 | 2005 Nissan Quest

1 Answer

Nissan Quest 2004 Tail Lights


Robynumber1,

Thanks for the email back. The nissan quest tail lights werenot operating, but the break lights were working. This was ultimately caused by a blown fuse. The fuse was blown by loose trailer lighting wires dragging on the ground, thus shorting. Problem fixed.

Aug 17, 2008 | 2004 Nissan Quest

1 Answer

BROKE TAIL LIGHT LENS AND BULB


Tiffany, there should be an access panel to remove to replace the bulb in your tail light.

Jun 19, 2008 | 2001 Nissan Quest

Not finding what you are looking for?
2008 Nissan Quest Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...