Question about 1999 Lincoln Town Car

Open Question

Catalytic converters over heating

Catalytic converters the two front ones after i installed a intake maniold please help

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many o2 sensors on a 99 Cadillac catera


Four .
Heated Oxygen Sensor (HO2S Bank 1 Position 1)
Located in RH front pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 1 Position 2)
Located in RH rear pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 2 Position 1)
Located in LH front pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 2 Position 2)
Located in LH rear pipe of the exhaust catalytic converter

Sep 21, 2015 | Cadillac Cars & Trucks

1 Answer

I have a 1996 buick lesabre 3800, just replaced fuel pressure regulator and upper intake plenum and gaskets b/c the EGR valve melted intake and coolant was leaking. I'm getting gas, spark, compression but...


One thing that might cause that is too much back pressure in the exhaust, like a clogged catalytic converter. Try disconnecting the exhaust in front of the converter and see if it starts.

Oct 21, 2013 | Cars & Trucks

1 Answer

I have a 2003 buick lesabre, in the past two months I have change, the radiator,water pump,heads,heads gasket, o2 sensors front up an down, my check light came back on an reading p420 cat..... I have now...


Take it back to who ever is guessing what the issue is and tell them to fix the intake gasket. IT was not installed correctly or torqued right. Depending on the mileage you may get a free catalytic converter. They are rated for 10 years. Contact a dealer about it. But if you had a blown head gasket and coolant got into the exhaust, the cat should be replaced. Silicon additives in coolant ruin catalytic converters

Oct 02, 2013 | 2003 Buick LeSabre

1 Answer

P0131 sabb 93 2001 po121 error codes


P0131 - O2 Sensor Circuit Low Voltage Bank 1 Sensor 1 (sensor is before the catalytic converter)

Possible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks
P0132 - O2 Sensor Circuit High Voltage Bank 1 Sensor 1
Possible causes- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

I am not really sure what is going on here with the same O2 sensor giving these lean and rich codes, if nothing else is apparent and the engine runs well you may have a defective O2 sensor.

Sep 13, 2012 | Saab 9 3 Cars & Trucks

3 Answers

2001 Nissan Sentra. Car starts with no power, but after a few restarts, gain power again. Code is PO420.


Hi, P0420 code means a catalytic converter fault.
The catalytic converter has an oxygen sensor in front and behind it. When the vehicle is warm and running in closed loop mode, the upstream oxygen sensor waveform reading should fluctuate. The downstream O2 sensor reading should be fairly steady. Typically the P0420 code triggers the Check Engine Light if the readings of the two sensors are similar. This is indicative of (among other things) a converter that is not working as efficiently as it should be (according to specs). It is part of the vehicle emissions system.
  • Check for exhaust leaks at the manifold, pipes, catalytic converter. Repair as required.
  • Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
  • Inspect the downstream heated oxygen sensor (HO2), replace if necessary
  • Replace the catalytic converter

Jul 22, 2011 | Nissan Sentra Cars & Trucks

1 Answer

What are the torque specs for 1996 Buick Century 3.1 L intake manifold?


Front Pipe REMOVAL & INSTALLATION Pipe Without Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal..
  2. Raise and support the front of the vehicle on jackstands.
  3. Remove the exhaust pipe-to-manifold nuts.
  4. Support the catalytic converter, then disconnect the pipe from the converter. Remove the pipe.
  5. Remove the exhaust gaskets. To install:
  6. Be sure to use all new gaskets when required. Assemble the system, check the clearance and tighten the bolts to about 15-30 ft. lbs. (20-41 Nm). Fig. 1: Front exhaust pipe connection common on vehicles with the catalytic converter not included 86813320.gif

  7. All clamps should be tightened to about 18-25 ft. lbs. (24-34 Nm). Do overtighten the clamps. If pipes become dented they can leak.
Pipe With Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal.
  2. Raise and support the vehicle.
  3. On some vehicles you will need to remove the brace from the transaxle.
  4. Remove the exhaust pipe nuts from the manifold.
  5. Support the catalytic converter pipe bolts from the rear of the converter.
  6. Lower the catalytic converter/front pipe assembly from the vehicle. To install:
  7. Be sure to use all new gaskets when required.
  8. Attach the new catalytic converter/front pipe assembly to the vehicle. Tighten the pipe to manifold nuts to 20-40 ft. lbs. (27-55 Nm).
  9. Attach the bolts at the rear of the catalytic converter/front pipe. Tighten them to 30-35 ft. lbs. (41-47 Nm).
  10. Connect the brace at the transaxle if removed.
  11. Lower the vehicle. prev.gif next.gif

Dec 18, 2010 | Buick Century Cars & Trucks

3 Answers

My check engine light came the code is p0420


Technical Description

Catalyst System Efficiency Below Threshold (Bank 1)
What does that mean?

The catalytic converter has an oxygen sensor in front and behind it. When the vehicle is warm and running in closed loop mode, the upstream oxygen sensor waveform reading should fluctuate. The downstream O2 sensor reading should be fairly steady. Typically the P0420 code triggers the Check Engine Light if the readings of the two sensors are similar. This is indicative of (among other things) a converter that is not working as efficiently as it should be (according to specs). It is part of the vehicle emissions system.
Symptoms

You will likely not notice any drivability problems, although there may be symptoms.
Causes

A code P0420 may mean that one or more of the following has happened:

* Leaded fuel was used where unleaded was called for
* An oxygen sensor is not reading (functioning) properly
* The engine coolant temperature sensor is not working properly
* Damaged or leaking exhaust manifold / catalytic converter / exhaust pipe
* Retarded spark timing
* The oxygen sensors in front and behind the converter are reporting too similar of readings

Possible Solutions

Some suggested steps for troubleshooting a P0420 error code include:

* Check for exhaust leaks at the manifold, pipes, catalytic converter. Repair as required.
* Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
* Inspect the downstream heated oxygen sensor (HO2), replace if necessary
* Replace the catalytic converter

One thing to note is that many vehicle manufacturers offer a longer warranty on emissions-related parts. So if you have a newer car but it's out of it's bumper-to-bumper warranty, there still may be warranty on this type of problem. Many manufacturers give a five year, unlimited mileage warranty on these items. It's worth checking into.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Sep 07, 2010 | 1996 Chevrolet Blazer

2 Answers

I have an 1998 Chevy Blazer and need to change the catalytic converter, are the flange bolts welded and can i cut them


Catalytic Converter Removal & Installation 2.2L Engine To Remove:
Catalytic converter 2.2L engine gm-03-22-734.gif

  1. Raise and safely support the vehicle.
  2. Disconnect the heated oxygen sensor (HO2S) electrical connector.
  3. Remove the exhaust manifold pipe flange mounting nuts from the catalytic converter.
  4. Remove the catalytic converter flange mounting nuts from the muffler.
  5. Remove the catalytic converter from the muffler.
  6. Remove the catalytic converter from the rear hanger bracket insulator.
  7. Remove the catalytic converter.
  8. Remove the (HO2S) from the catalytic converter.
To Install:
  1. Install the (HO2S) to the catalytic converter.
  2. Install a new gasket and the catalytic converter to the muffler.
  3. Install catalytic converter to the catalytic converter hanger.
  4. Install the catalytic converter flange mounting nuts to the muffler flange.
    • Tighten to 26 ft lbs (35 Nm).
  5. Install the catalytic converter flange mounting nuts to the exhaust manifold pipe flange.
    • Tighten to 26 ft lbs (35 Nm).
  6. Connect the heated oxygen sensor (HO2S) electrical connector.
  7. Lower the vehicle.
------ Catalytic Converter Removal & Installation 4.3L Engine To Remove:
  1. Raise and safely support the vehicle.
  2. Raise and support the transmission.
  3. Remove the transmission support
  4. Disconnect the left and right pre-converter heated oxygen sensor (HO2S) electrical connector.
  5. Disconnect the post-converter (HO2S) connector. Muffler flange and gasket gm-03-43-731.gif

  6. Remove the catalytic converter flange mounting nuts from the muffler.
  7. Remove the catalytic converter from the muffler.
  8. Remove the exhaust manifold flange mounting nuts from the catalytic converter. Catalytic converter 4.3L engine gm-03-43-735.gif

  9. Remove the catalytic converter from the support bracket insulator.
  10. Remove the catalytic converter and gaskets.
  11. Remove the heated oxygen sensor.
To Install:
  1. Install the heated oxygen sensors as needed.
  2. Install a new gasket and the Install the catalytic converter to the support bracket insulator.
  3. Install the catalytic converter to the exhaust manifold flange. Install the mounting nuts.
    • Tighten to 39 ft lbs (53 Nm).
  4. Using a new flange gasket, install the catalytic converter to the muffler. Install the mounting nuts.
    • Tighten to 30 ft lbs (40 Nm).
  5. Connect the left and right pre-converter heated oxygen sensor (HO2S) electrical connectors.
  6. Connect the post-converter (HO2S) electrical connector.
  7. Install the transmission support.
  8. Lower the transmission.
  9. Lower the vehicle.
prev.gif next.gif ---
It looks like you can cut them and replace them with new bolts and nuts.prev.gif next.gif

Sep 05, 2010 | 1998 Chevrolet Blazer

3 Answers

Were on exaust is oxygen sensor in 1999 subaru impreza auto sport


On the SOHC engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the front catalytic converter. On the DOHC engine the front oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the catalytic converter.

Oxygen sensor location-Baja 2.5L SOHC engine
c3fce0b.jpg

Oxygen sensor location-Baja 2.5L DOHC engine
7aac75e.jpg


On the 2.0L engine the front (A/F) oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the rear catalytic converter. On the 2.2L engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the rear catalytic converter.

Oxygen sensor location-Impreza 1998-2001 2.2L engine
a5973e4.jpg


moz-screenshot.pngOxygen sensor location-Impreza 1998-2002 2.5L SOHC engine
3a84717.jpg
I hope helped with this; remember rated this help. Good luck.

Nov 20, 2009 | 1999 Subaru Impreza

3 Answers

I was told that my 98 s70 volvo has a emmissions leak what does this means?


it means that if u have a catalytic converter then ur catalytic converter which reduce the emissions is not working in proper manner which it means that it is broken

Jun 08, 2009 | 2000 Volvo S70

Not finding what you are looking for?
1999 Lincoln Town Car Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

fordexpert

Level 3 Expert

5474 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...