Question about 2006 Chevrolet Venture

Open Question

Remove tray between front seats

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Carpets are wet under driver and passenger front seats neat the rear mounts of the seats. What could cause this and how can it be fixed? Thank you


A leaking heater core will allow water to run out of the case under the dash and pool under the carpet.

Nov 18, 2014 | 2000 Jaguar S-Type

2 Answers

How to remove the headrests from the driver and passenger seat of a 2007 Chevy Uplander?


Remove the storage tray from the back of the driver and passenger seats. This can be a trick in itself. You have to squeeze together some body style clips with needle nose pliers going in from the bottom where the tray section meets the seat fabric. When you get the right and left hand side clips free the tray panel should just tilt out at bottom. Then just slide the whole tray panel up and then you can pull it out. Now you can get to the head rests. From the inside of the seat you can see the 2 head rest posts that connect to the cushion portion of it. Follow the 2 posts up until you see the black plastic sleeves they slide in. Take some channel locks and grab the black sleeves and turn them (they only turn one way) until the cut outs in the bottom of the sleeves are facing the front and rear of the van rather than the right and left sides. Once these are turned you can easily lift the whole head rest out.

May 26, 2011 | 2007 Chevrolet Uplander

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

Remove front seat


SECTION 501-10: Seating 1998 Escort/Tracer Workshop Manual REMOVAL AND INSTALLATION Seat —Front Removal
NOTE: Driver side seat shown, passenger side seat similar.
  1. Slide the seat to its rearward position.
  1. Remove the front seat track to floor front bolts.
  1. Slide the seat to the forward position.
  1. Remove the front seat track to floor rear bolts.
  1. Disconnect the safety belt warning indicator switch electrical connector.
  1. Remove the front seat.

Dec 06, 2009 | 1998 Ford Escort

1 Answer

Front passenger side seat


all you need to do is take the 2 14mm bolts off on the front.. and remove the little plastic covers on the back side (same place on the frame as the front) you might be able to shake it out but if not there is a couple of wires that you need to unplug one is 16 pin plug. that runs the power just pull the clip off and unplug it by pushing the tab and pulling it out.. and remove the yellow clips.. by pushing them together then pulling like one of those asian finger things... BUT BE CAREFUL the yellow ones are ABS make sure the car is off and the key out of the ignition... if you make all the way to this point take the seat out and turn it around and shake it out there might be come covers that you need a phillips screwdriver to get out... but don't be scared it's really easy to put back together just take your time and try not to bend the plastic clips... email me if you have anymore questions..

Aug 15, 2009 | 2007 Honda Odyssey

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

1 Answer

Rear seatbelt


fold rear down take outter seat off one twelve bolt at bottom remove clps and pck tray YOU GOT IT

Mar 07, 2009 | 1997 Toyota Camry

1 Answer

Removal of center tray on Saturn Relay


Remove the seat. Should be some torx head bolt attaching it to the seat.

Dec 21, 2008 | 2005 Saturn Relay

Not finding what you are looking for?
2006 Chevrolet Venture Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...