Question about 2005 Nissan Sentra 1.8
Car interior remains cold with heater select switch dialed up to HOT. Temp difference on heater supply/return hoses shows heat exchange is occurring but car interior remains cold. Antifreeze level in radiator and expansion tank remains the same whether or not engine is running. Mist formation on inside of windshield can only be cleared manually or by running the A/C upon initial start up on cold mornings or when it rains.
Sounds like the heater - ac door actuator is not working. This part would need to be replaced, it's not repairable.
Posted on Nov 24, 2013
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The blend door in the plenum is not moving. IT could be the control arm or the control or the door or the shaft. You can access it through the glove box.
Posted on Aug 11, 2012
SOURCE: heater blowing cold air
My 2005 Nissan Sentra 1.8s with 55,000 mi. blows cold air from the heater. Coolant not circulating in engine. Lower hose stays cool to touch. Both heater hoses cold. Changed thermostat - didn't fix it. Coolant not leaking or dirty. None in oil - no oil in radiator. Changed worn water pump belt - pump spins freely with no noise or resistance. Cooling fans come on after warm-up. Temperature gauge stays in normal range then jumps to hot and back again. Coolant good to 10 below - didn't freeze here yet. No other problems or repairs to car. Afraid to drive and make worse. Help!
Posted on Oct 16, 2009
SOURCE: How to replace thermostat on
Do this when cool. Take radiator cap off, start the engine, turn on heat (not defrost) and now top up coolant to about an inch or 2 from top of radiator, as level drops down, and let vehicle run until the radiator fan comes on, then off, about 3 times, and add coolant as needed while it's running. After that, put radiator cap back on tight & make sure return bottle is filled to proper level. Now try that & see how heat is, temperature gauge etc, and keep an eye on return bottle level for a while. Let me know how it is.
Posted on Mar 27, 2009
SOURCE: heater blowing cold air
My 05 sentra with 79k miles heat will warm up and then get cold after a mile of driving, we have tried to get the air pocket out, the mechanic stated he thought it could be a blown head gasket, another mechanic said it was a bad heater core. Any advice would be appreciated.
Posted on Dec 05, 2009
You most likely have an "AIR LOCK" within the Heater Core. This requires one to pressurize the Cooling System and loosen the heater hose at the HIGHEST POINT and bleed the Air out of the Heater Core. I am not familiar with the Nissan but have encountered this problem numerous times over the years. Most late model vehicles are equipped with Air Bleed devices which must be utilized any time coolant is drained and refilled.
Most all reputable Auto Parts stores sell and/or rent a pump that temporarily replaces the Pressure Cap that may be utilized to pressurize the system for this purpose. If you don't feel capable of performing the bleeding operation take your vehicle to an ASE Certified Mechanic and have it done correctly.
Posted on Dec 07, 2009
Testimonial: "Great advice. That's what I thought it might be, but I wanted someone else's opinion on the matter. Thanks a lot."
Tips for a great answer:
Oct 10, 2016 | Jeep Cars & Trucks
Sep 20, 2015 | Pontiac Grand Prix Cars & Trucks
Oct 08, 2013 | 2005 Nissan Sentra
Jan 15, 2013 | 2002 Nissan Sentra
Aug 10, 2012 | 2002 Nissan Sentra
Apr 30, 2010 | 2005 Nissan Sentra
May 13, 2009 | 2002 Nissan Maxima
Feb 13, 2009 | 1993 Nissan Sentra 4 Door
Dec 22, 2008 | 2002 Nissan Sentra
Nov 24, 2008 | 2005 Nissan Sentra
352 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: