Question about 2005 Chrysler 300
U1120 means the PCM doesn't receive a vehicle speed signal from the Anti-lock brake Module over the CAN C bus. This can be caused by the ABS module, PCM or something wrong with the can bus. This might be just an erroneous code and may never set again.
Posted on Nov 26, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2006 Chrysler 300, no start
It is all about troubleshooting. Possible causes are a dead battery. Did someone try to steal it and cut the wrong wires underneath?
The starter solenoid could be bad.
If the headlights stay bright when you try to start the car then it is not the battery. if you hear clicking and the headlights are very dim then it is likely to be the battery. If you have full battery with good cable connections and you get very active clicking but no starts then the solenoid on the starter has burned contacts. if battery is good but no clicking when trying to start then the problem is in the key area or alarm system.
All the areas mentioned above are place to start and troubleshooting steps.
Posted on Mar 09, 2010
Testimonial: "Thanks for the input, I'll go through the systems individually and see what I come up with Thanks again, A"
In the 2006 manual The fuse for this is listed as #44. It is a 20 AMP fuse. Looking at the diagram, it appears to be one of the larger square shaped ones that are, It is listed to be in the "Power Distribution Center".
Hope this helps.
Posted on Mar 11, 2010
Testimonial: "thank you for the info. But all I need to know is WHERE IS DISB CENTER IS? Under the hood? Is it inside? Thx again Rich"
This is quite a process....
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.
3) Disconnect the CHMSL electrical connector (1).
4) Remove the two mounting fasteners (3) to the CHMSL (2).
Installation is opposite of removal.
Rear shelf trim panel
1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.
1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.
C-pillar trim removal
Hope this all gets it done for you........
Posted on Mar 12, 2010
Tips for a great answer:
Aug 11, 2016 | Chrysler Cars & Trucks
Nov 09, 2014 | 2005 Chrysler 300
Oct 20, 2014 | 2006 Chrysler 300
Sep 30, 2014 | 2006 Chrysler 300 Touring
Apr 14, 2013 | 2004 Dodge Durango
Sep 26, 2008 | 2006 Chrysler 300
607 people viewed this question
Usually answered in minutes!