Question about 1996 Ford Thunderbird LX

Open Question

Trouble code pf p1445 - 1996 Ford Thunderbird LX

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What solution on p1445 secondary air injection system switching valve no2 bank2 stuck close


Year make and model? This code usually refers to the purge control valve circuit being high

Jul 10, 2015 | Cars & Trucks

1 Answer

What is a fault code p1445 on a deisel 407 ?


Canister purge fault in the emissions system.

Aug 05, 2014 | 2005 Peugeot 407 1.8

1 Answer

What is a fault code p1445 ?


You use the internet to find obd codes

Type: OBD P1445

Aug 05, 2014 | 2005 Peugeot 407 1.8

1 Answer

P1445 code nissan maxima 1996


Here's a link to code P1400.Here's code P1445.Here's a link on the egr valve.Here's another link.

Mar 16, 2013 | 1996 Nissan Altima

1 Answer

I have a 1996 Nissan 240SX SE, I've been having the check engine light P0500 for a long time, I was told its not my speed sensor since my speedometer works. Also the error code P1445 my EVAP volume pu


P0500 since the speed dometer is working and you get the code P0500 The harness from the speedometer to the ECM need to be check, Go behind the spedometer disconnect and reconnect and retest,if you have a no go go to the ECM disconnect and reconnect and retest ,Your problem is basically in the harness from Speedometer to ECM.As for P1445 make it a hobby of inspecting the canister purge valve hose for rupture or torn if all good replace the purge valve

Nov 11, 2012 | Cars & Trucks

1 Answer

Error code P1445


Code has to do with the air injection system, Take it from there if you can solve the problem with it,

Nov 06, 2012 | 2005 Toyota Sequoia SR5

2 Answers

Code p1445


P1445: CHECK PF SENSOR HIGH VOLTAGE TO PCM
Continuous Memory Diagnostic Trouble Code (DTC) P1445 indicates that Self-Test has detected a PF sensor circuit input above the maximum.

Possible causes:

PF shorted to VPWR.
PF open circuit.
PWR GND open circuit.
Damaged purge flow (PF) sensor.
Damaged PCM.

Jul 24, 2011 | 1996 Mercury Cougar XR7

1 Answer

Hi, I'm getting code p1445 (additive level too high) after I refill additive (fit almost 4 lit.). I try to reset counter to zero but ecu reply there is no communication with ecu and on display message...


recently had similar problem 307 55 hdi engine code RHR getting p1445 + p1435. Hooked car up to launch 431 code reader got p1445 purge flow sensor circuit high input. pa435 a/c ref temp circuit range/performance no contact. Then hooked to snap on ethos p1445 diesel additive system quantity too high. p1435 diesel additive system incorrect message from can bus. checked tank level 1/3-1/2 tank about right for 55k fired pump by shorting briefly appeared to work as youd expect. few hours later after dismantleing most of car looking for depolution ecu stumped ! next day dropped in to local peugeot dealer who i know well after a conflab they agreed these are common codes easy solution! The depolution ecu is found either beside the passenger seat (left) against the sill or depending on where its built behind the fuse board/glove box (where this one was) just remove felt under glove box look up with torch behind fuse board youll see big relay type unit with slide out release (red) unplug clean (toothbrush w40) apply vv slight pressure to pins to adjust contact, refit, clear codes job done !! Common problem apparently worked for me easy & simple place to start !

Jan 18, 2011 | Peugeot Liberte Cars & Trucks

2 Answers

1996 nissan maxima check engine light on the mecanic used scaner two code p0500 speed sensor and p1445 manufactory controler auxiliary controls. what can I do? can I fix it?can i buy the parts ? can i...


Firstly, the code p1445 is actually an EVAP Canister Purge Control Valve...The most common problem is a failure of the valve itself, which is located at the top of the plenum chamber. Nissan offers a replacement valve with new bracket and hoses. It is around the $150-$200.00 mark.

But, remember to test the component (valve) first as this suggestion is just to the common problem, but in rare cases, it might be PCM related (water entry, shock etc)

Secondly, the p0500 code is a speed sensor and you can pick these up from autozone.....it provides the road speed for the speedometer and odometer..........if these are working fine, then you might have a wiring issue.

As these are 2 seperate systems, I doubt that they are related.

I hope this helps

Sep 22, 2010 | 1996 Nissan Maxima

2 Answers

P1443 computer code what is it on my 1996 ford thunderbird


P1443 = A problem with the EVAP purge flow system
Continuous Memory Diagnostic Trouble Code (DTC) P1443 indicates an incorrect Evaporative System Purge Control Valve flow.

Possible causes:
-- Obstructed, open or cracked hoses between EVAP canister purge valve and intake manifold.
-- Damaged EVAP canister purge valve.
-- Damaged PF sensor.

Hope help with this.

Apr 25, 2010 | 1996 Ford Thunderbird LX

Not finding what you are looking for?
1996 Ford Thunderbird LX Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...