Question about 2010 Dodge Grand Caravan

Open Question

What is the socket size for 2010 dodge grand caravan hub nut

Wheel bearing hub assy nut

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1118 Answers

SOURCE: Shadtree replacement of a front wheel bearing possible?

the nut is special its metric, the parts store will know its like a 30or35. i know an inch and a half socket is to small If you got the tool i see no problem. you may have to tap on it a little but it should come right out.

Posted on Feb 04, 2009

Ad
  • 137 Answers

SOURCE: What size socket for a front wheel bearing hub nut

36mm

Posted on Jul 11, 2009

fingaz22
  • 1068 Answers

SOURCE: What size socket for 2003 Dodge Dakota 2wd front

36mm if it has the factor axle still in it. if change could be a 34mm. hope that helps good lcuk

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

2 Answers

How hard is it to change out both front wheel bearings


Not that hard, you will need to remove the brake calipers and rotors. The hardest part is getting the proper size socket to take the axle nut off the spindle if its 4WD. If 2WD they just bolt on from the back of the spindle (4 bolts), and electrical connector for the ABS. Leave the ball joints and tie rods connected.

Jan 28, 2011 | 2000 GMC Jimmy

1 Answer

How long does it take to fix front bearings on a 97 dodge caravan? and cost


About an hour a side...This is the whole job and pictures....

The hub and wheel bearing unit is serviced as a complete assembly. Replacement of the front drive hub and bearing assembly can be done without having to remove the steering knuckle from the vehicle. However, if the hub/bearing assembly is frozen to the steering knuckle, removal of the steering knuckle is required.
  1. Disconnect the negative battery cable.
  2. Remove the cotter pin from the end of the stub axle. Remove the nut lock and spring washer. With the brakes applied, loosen, but do NOT remove the axle nut and washer with the vehicle still on the ground or damage to the wheel bearing will result.
  3. Raise and safely support the vehicle. Remove the wheel.
  4. Remove the front brake caliper assembly from the steering knuckle assembly and support from the strut assembly using a strong piece of wire.
    1. Remove the front brake rotor from the hub/bearing assembly.
    2. Remove the retaining nut and washer from the halfshaft stub axle.
    3. Remove the ABS wheel speed sensor from the steering knuckle.
    4. Remove the 4 hub and bearing assembly mounting bolts from behind the steering knuckle.
    5. Remove the hub and bearing assembly from the steering knuckle.
  5. To install:
    1. Thoroughly clean the mating surfaces of the steering knuckle and the hub and bearing assembly of any foreign material or nicks so the surfaces are clean and smooth.
    2. Install the new hub and bearing assembly and tighten the mounting bolts in a crisscross pattern to 45 ft. lbs. (65 Nm). Be sure the hub and bearing assembly is seated squarely against the front steering knuckle.
    3. Install the disc brake rotor.
    4. Install the brake caliper assembly onto the steering knuckle.
    5. Install the axle washer and nut. Tighten but do not torque.
    6. Install the ABS wheel speed sensor.
    7. Install the wheel and lug nuts. Torque the lug nuts, in sequence, to 95 ft. lbs. (129 Nm).
    8. Lower the vehicle. Do NOT roll the vehicle until the axle nut has been properly torqued or damage to the front wheel bearings will result.
    9. With the vehicle's brakes applied, torque the axle nut to 180 ft. lbs. (244 Nm). Install the spring washer, nut lock and a new cotter pin. Wrap the cotter pin prongs tightly around the axle nut lock.
    10. Reconnect the negative battery cable. Check the wheel alignment.

fe8edd6.gif
The hub/bearing assembly is attached to the steering knuckle with four bolts


9733319.gif
Removing a hub/bearing assembly



1867b08.gif
If the hub/bearing is "frozen" to the steering knuckle, separate the ball joint and lightly tap on the hub/bearing from behind



09233ac.gif
The hub/bearing assembly should free itself from the steering knuckle

About $60 a hub.

May 23, 2010 | 1997 Dodge Caravan

1 Answer

How to remove routers for a for bronco 85 302 full sized


Removing rotors.

1. Jack up, put on jack stands and remove tire (obviously)
2. Remove caliper
3. Remove bolts holding locking hub body to hub
4. Remove snap ring from end of axle, Remove hub retainer ring from ID of wheel hub. Use a small screwdriver or pick to start it out of the groove. Remove the hub body
5. Remove the outer bearing lock nut, lock washer and the inner adjusting nut
You need the special socket for this OTC #7158 or similar
6. Remove the outer bearing and then the hub
7. To separate the rotor from the hub, use a soft faced hammer to drive the studs out
8. Turn the hub over and set the new rotor in place. Put the studs back in.
9. I will usually use an air hammer to drive the studs back in. Alternating in a circular pattern. If you don't have access, you can use a large diameter punch or another hammer on the back of the studs.
10. Now would be a good time to repack the bearings and replace the wheel seals. Pull the spindles and check the bearings and seals in the back of them. If they are not rusted, slab some grease on them and put back together.
11. Install the hub and rotor assy, and the outer bearing and bearing adjustment nut.

Apr 25, 2010 | 1985 Ford Bronco

1 Answer

Wheel Bearings


Hello tclinch.
Your Grand Caravan has hub assemblies front and rear. Also if yours is all wheel drive it has a rear hub as well. Just different removal processes.
Hope your repair goes well for you.

Nov 27, 2009 | 1999 Dodge Grand Caravan

1 Answer

How to fit a wheel bearing on an s type jaguar 1999


My friend;
Try this;
  1. Remove the tire assy.
  2. Remove the cotter pin inside the nut holding the wheel hub assy.
  3. Remove the nut holding the wheel hub assy.
  4. Remove the wheel hub assy. & if there is circlips {Retaining} holding the bearings snap them by small slotted screwdriver.
  5. Install the bearings in the wheel hub assy.
Reverse the Removal process to Install the removed parts.
Or consult the internet Jaguar Forums.
Try it, & PLZ; let me know if I add any benefits to you.
I hope I add some thing valuable to you.
Regards;
MAR;
soer2@yahoo.com

Nov 09, 2009 | 2000 Jaguar S-Type

2 Answers

Replacing front wheel hub assembly 1996 Dodge caravan


You can get a complete hub with bearing and its can just be bolted on, without having to have bearing pressed in and out. Good luck and thanks for using FIX YA

Mar 19, 2009 | 1996 Dodge Caravan

Not finding what you are looking for?
2010 Dodge Grand Caravan Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...