Question about 2000 Lincoln LS

Open Question

How do i put.on.a water outlet for a 2001 lincoln ls its the back two bolts that the.problem

The back to bolt cant be got to I. think I got to take off manafold

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The back bolts on my thermostat /water outlet is hard to get to.on my 2000 lincoln ls what tools do i need


should be able to get to it with a flex-socket,unless it's best for you to remove whatever is in the way (try first with a flex-socket and extension. MAKE SURE YOU HAND START THE BOLTS TO MAKE SURE YOU DON'T CROSS-THREAD AND TIGHTEN EVENLY AS TO PREVENT BREAKING THE NEW PIECE.

Dec 29, 2013 | 2000 Lincoln LS

1 Answer

Engine coolant thermostat/water outlet assembly replace for 2000 lincoln ls


First with the engine cool, drain some of the antifreeze from the radiator. Second, take the hose clamp off of the upper radiator hose on the engine side and slide the hose off the water neck, some antifreeze might spill out. Third, remove the two bolts that hold the water neck and remove the waterneck, some antifreeze may spill out. Fourth, remove the old thermostat and o-ring , clean the sealing surface and install the new thermostat and o-ring the same way it came out. Last just reverse the procedure to get it back together, tightening the two waterneck bolts to 18 ft. Lbs. Fill with 50/50 antifreeze and water start it up and check for leaks. And you are done. Should only take about 20-30 minutes

Nov 06, 2013 | Lincoln LS Cars & Trucks

1 Answer

After i took the bolt off the harmonic balancer and the washer came off the harmonic balancer still will not budge on my 2001 lincoln ls V-6 model what am i missing?


You'll probably need to use a large gear puller - the balancer may be forced onto the crankshaft by the center bolt.

Aug 25, 2012 | 2001 Lincoln LS

1 Answer

2001 lincoln ls harmonic balancer pulley out of line


Your pulley may be coming loose. There should be a large bolt holding it to the Crankshaft. You would need to tighten the bolt and the pulley should draw back into place.

On some of the pulleys there may be a 2 piece construction with a thinner outer ring held in place by a rubber gasket ring. If the adhesive is slipping you need a new part as these should have been pressed on during manufacturing.

Nov 07, 2011 | 2001 Lincoln LS

1 Answer

How do I replace my trunk latch on my 2001 lincoln Ls


Open trunk
Remove three bolts holding latch
Remove actuating cable.

May 21, 2010 | 2001 Lincoln LS

1 Answer

I need to reconnect my radiator in my 2000 ls v8


For 2000 Lincoln LS 3.9L SFI DOHC 8cyl...
Radiator - Removal & Installation
  1. Drain the engine cooling system.
  2. Remove the upper radiator sight shield.
  3. Remove the air cleaner outlet tube.
  4. Remove the six bolts and the two radiator upper support brackets.
  5. Remove the upper radiator hose.
  6. Remove the bolt and position the receiver drier aside.
  7. Disconnect the dual flow coolant valve electrical connector and the A/C line from the fan shroud.
  8. 3.0L engines only:
    Disconnect the Throttle Position (TP) sensor and the Idle Air Control (IAC) valve electrical connectors.
  9. Remove the bolts.
  10. Remove the bracket.
  11. 3.9L engines only:
    Remove the bolt and position the electric water pump aside.
  12. Disconnect the high pressure cooling fan bracket and line.
  13. Inspect the seal and install a new seal if necessary.
  14. Disconnect the return hose from the cooling fan and shroud.
  15. Separate the return hose from the fan shroud and position aside.
  16. Remove the two bolts and the fan shroud assembly.
  17. Remove the A/C condenser.
  18. Remove the two bolts and position the multi-cooler assembly aside.
  19. Remove the bolts and the condenser support brackets.
  20. Remove the radiator.

To install:
  1. Install the following:

    Radiator Condenser support brackets Multi-cooler assembly A/C condenser Fan shroud assembly
  2. Connect the return hose to the fan shroud
  3. Connect the high pressure cooling fan bracket and line.
  4. 3.9L engines only:
    Replace the bolt and position the electric water pump aside.
  5. 3.0L engines only:
    Connect the Throttle Position (TP) sensor and the Idle Air Control (IAC) valve electrical connectors.
  6. Replace the following
    The upper radiator sight shield. The air cleaner outlet tube. The six bolts and the two radiator upper support brackets. The upper radiator hose. The bolt and position the receiver drier aside.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2000 Lincoln LS

1 Answer

I can't open my trunk of my 2000 lincoln ls. How can I open from the back seat?


maybe, the bottom cushin pops up. the back should have two bolts holding it down. behind the seat back will be an opening but if you are small enough to fit thru the opening.

Oct 27, 2009 | 2001 Lincoln LS

2 Answers

How do i put a coil in a 2001 jaguar s type


303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system.
---------------------------------------------------------------------------------------
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
DESCRIPTION AND OPERATION Engine Ignition The electronic ignition (EI) system is a coil-on-plug (COP) ignition system
-----------------------------------------------------------------------------
v-8
SECTION 303-07B: Engine Ignition — 3.9L 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal
  1. Remove the air cleaner outlet tube. For additional information, refer to Section 303-12 .
  1. Remove the bolts and the ignition coil cover.
7b000cd.gif
  1. Disconnect the electrical connector from each ignition coil.
a1d93dd.gif
  1. Remove the ignition coils.
    1. Remove the bolts.
    1. Remove the ignition coils.
------------------------------------------------
v-6

SECTION 303-07A: Engine Ignition — 3.0L (4V) 2001 Lincoln LS Workshop Manual
REMOVAL AND INSTALLATION Ignition Coil Removal
  1. Remove the engine appearance cover.
  1. To access the RH bank ignition coils, remove the upper intake manifold. For additional information, refer to Section 303-01A .
  1. Disconnect the electrical connector from the ignition coils.
  1. Remove the bolts.
  1. Remove the ignition coils.
please rate as fixed if this helps.

Apr 28, 2009 | 2001 Jaguar S-Type

2 Answers

Trasmission fluid?


there should be a dipstick on the drivers side of the car under the hood to add tranny fluid.it should be red in color

Dec 25, 2008 | 2001 Lincoln LS

Not finding what you are looking for?
2000 Lincoln LS Logo

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

fordexpert

Level 3 Expert

5467 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...