Question about 2000 Jeep Grand Cherokee

1 Answer

Heater does not blow air

When engine is turned on the heater does not blow any air how can I fix this problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Zero air flow.
#1 is bad fuse fan.
if it fails on high , the fuse is blown,
replace it or test it with a an ohm meter .
DMM meter. select, ohms Rx2 (low range)
zero ohms is good, infinity is bad.
a 100% accurate test. every time.

Posted on Nov 25, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why hot air dont blow out of vent?


Probably have a bad Door Airflow control box

Dec 04, 2016 | Toyota Cars & Trucks

1 Answer

Warm aire on one side cold air on the other


Does it have passenger side controls

Feb 25, 2014 | Cars & Trucks

1 Answer

There is no heat from heater at engine idle speed.


I have to believe that your thermostat is still sticking....replace it and you problem should go away. Relatively inexpensive fix.

Jan 23, 2013 | Cars & Trucks

1 Answer

How can i get the vents to blow cool or cold air instead of hot air


Your Heater tap is probably stuck in the on posision. This is in the engine bay. Not sure if yors is vacume, electric or cable operated. Temporary fix bypass the heater alltogether ie: put the hoses that go to the tap reroute to the motor

Jul 05, 2012 | 2010 Chevrolet Traverse

1 Answer

My air conditioner blows hot air and my heater blows cold air. The heater will warm up after the engine has been running for awhile but when I turn the air conditioner on it takes power away from the...


check your blower motor under the passenger side of the dash, round plastic box three screws pull it out something might have fallen though your cowl and chewed up the fan blades. as for the ac your r-12 is probly empty or has a leak bring it to a local garage and have them flush and fill your cooling system. heater would be your thermostat not openig properly, by far your cheapest fix under ten dollar part.

Apr 04, 2012 | 2000 Toyota 4Runner

1 Answer

No heat air is blowing cold


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is worm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest to flush the heater core.

Oct 22, 2009 | 1998 Ford Taurus

1 Answer

MY 1998 FOR TARUS HEATER WILL NOT WORK.WAS DRIVING


It is most probably the problem with blend door or blend door actuator. But just in case I would suggest to follow the entire procedure:

First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Heater not working


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Heater temp on mercury '98 mountaineer only blows hot


Everything that is heat and cooling in a vehicle is controlled by vacuum from the engine. It appears to me that your blend door vacuum line to the temp control switch is either off or cracked/broken and not making things work the way you want/expect. It's the vacuum friend.

Jul 01, 2017 | 1998 Mercury Mountaineer

2 Answers

Heater blows cold on 02 chevy silverado 1500 4.3 V6


i had the same problem with my 2000 chevy truck!! i took both hoses off engine and flushed the heater core with water and air frome air compresser,added new coolent and it works perfect!!!! so try flushing your system............

Nov 17, 2008 | 2002 Chevrolet Silverado 1500HD

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...