Question about Cars & Trucks

Open Question

Mazda etude overheated and gasket replaced but still has low power.could it damaged camshaftsensor

It starts then goes off

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1996 Mazda Etude 160 Timing Belt

The timing belt has 123 teeth, and ussualy the marks are little paints. align them together and then you will have ur problem solved.

Posted on Oct 24, 2008

  • 27 Answers

SOURCE: engine overheating

All i can think of is the thermostat is not opening. or you may have a clog somewhere preventing the flow. Check the T-stat and hoses and radiator ( for clogs) Good luck

Posted on Aug 05, 2009

  • 1 Answer

SOURCE: Mazda Etude 160ie timing

I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Posted on Nov 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi my Mazda etude 1999 model is overheating oil the water is boiling in side the cooler once you switch off the engine but inside the deshboard the heat gaurd its normal so I don't know what wrong


Sounds like you may have a blown head gasket. If there is oil in the coolant, and musty brown look and smells bad that's the culprit. I would do a rad flush and oil change and see what happens next...

Dec 21, 2016 | Mazda Cars & Trucks

1 Answer

What damage can be caused to a vehicle engine overheats


Hi Anonymous,
It probably depends how far you drove after the car overheated. It is extremely bad news to drive an overheated car.
Typically the head gasket (between the cylinder head and the engine block) will warp when the coolant goes dry and the engine overheats. And then it leaks - both on the outside of the engine block and with big white smoke out the tailpipe.
Replacing the head gasket is doable but expensive.
But if you don't see any leaks on the block or white smoke you may have dodged a bullet.
Hope this helps,
Bud

Jul 15, 2014 | Mazda 6 Cars & Trucks

1 Answer

Overheated and loss compression.


The most common cause is a blown head gasket and sometimes a warped head. Someone would need to remove the cylinder head and have it checked for damage, then replace the head gasket.

Jul 15, 2013 | 2001 Mazda 626

1 Answer

On hot days the etude cuts out whilst driving, after +- 20 minutes it starts again and drives as if nothing is wrong.


I have seen corrosion problems inside the coil end of coil wires on slightly older Mazdas. not sure if yours has a distributor or not, but if it does, this type of corrosion could be overheating the coil. would suggest if applicable, replacing both the coil, and the spark plug wires.

Aug 17, 2011 | 1999 Mazda 626

1 Answer

My mazda etude is having water in one of the spark plugs


Remove that plug and turn engine over. Does water shoot out of the spark plug hole? Head gasket leak, cylinder-to-coolant channel side. Do you see any water vapor or actual water out of your exhaust when you first start it?

Nov 28, 2010 | 1997 Mazda Protege

1 Answer

My 1998 mazda protege overheated and now it wont start


SOUND LIKE BLOWED HEAD GASKET.BUT WAIT TO SEE IF ENGINE WILL CRANK WHEN ENGINE COOL DOWN.MOST CARS PCM WILL SHUT CAR DOWN TO KEEP FROM DAMAGING THE ENGINE.CHECK FOR LOW COOLANT.YOUR OVERHEATING PROBLEM COULD BE CAUSED BY BAD THERMOSTAT OR WATER PUMP.CHECK PUMP WEEP HOLE TO SEE IF LEAKING.IF YES REPLACE WATER PUMP.

Mar 28, 2010 | 1998 Mazda Protege

2 Answers

Mazda Etude 160ie timing


I have a problem with the mazda etude 160ise, the crank shaft sensor was damages and replaced it ad now the car cant tart. Note that the timing was afected in that the two sealings were replaced. Could one please provide information as to how I can get in timing and get it going again.

Jan 02, 2009 | 2004 Mazda 3

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...