Question about 2008 Nissan Altima Hybrid

Open Question

How to change a 120 amp fuse

How do i remove a blown 120 amp fuse properly? it wont seem to budge and is already broken

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the fuses?


Remove the fuse box cover remove old place new fuse of same size. Step by Step:
  1. Locate your car's fuse panel.
  2. Take off the fuse panel's cover.
  3. Locate the blown fuse.
  4. Remove the broken fuse.
  5. Insert a replacement fuse of the correct amperage-make note of the fuse panel and your owner's manual on this one.
  6. You do keep a few extra fuses of various amperage in your glove box.

How to Find and Replace Blown Fuse in Your Car or Truck

Changing Fuse DMV org

How to Change Vehicle Fuses

How to Change Car Fuse in 8 Easy Steps

May 30, 2016 | Cars & Trucks

1 Answer

1998 Jeep Laredo continuous clicking sound passenger side under dash it runs battery down ignition is off continuous clicking please help thank you


A number of people in the link report the same problem on the Jeep Forum and there are a number of fixes.

I also found this for you.

The problem seems to be a short in one of the rear dome lights, which seems to be affecting two fuse circuits. The temporary solution was to remove one fuse and replace another (blown), and remove the bulb from the bad dome light. I had to remove "fuze#5-15 amps-Interior Lighting", this stopped the clicking noise, I replaced blown fuze#8-15 amp-Overhead Console, keyless Entry ..." This fuse also seems to effect the alarm system (contrary to the documentation), and I think that was what was killing the engine. The problem existed before fuse#8 blew. Removing fuse#5 may have solved the problem, but the other fuse blew while I was testing the dome lights, and the jeep will not start without it.

Found lots of wires bare or broken in all the door wiring harnesses ( in rubber boot that goes to the door)I first checked both fuse 5 and 8 but both o.k. After fixing the broken wires found fuse 8 had blown. Replaced that and all is well again. Thanks for the advise got me looking in the right direction.

. Fuse box located in passenger side door jam...check #8 fuse if its not blown check others...if it is blown, check your radio, and interior lights for good ground
Clicking noise under passenger dash Jeep just shuts down

Jan 10, 2016 | Jeep Cars & Trucks

1 Answer

Radio Dead and already changed fuses that were not blown


Yes and fuses are tricky some don't look blown and they r, and some look blown and r not But to check the radio itself put a volt meter to the wiring connection on back of unit

Jan 02, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

Sunroof is not working


might be blown relay or fuse. may not have anything to do with battery change. test switch & motor if relay and fuse is ok.

Apr 14, 2013 | 2006 Cadillac CTS

1 Answer

On a 1997 cutlass my dash lites wont work and courtesy lites wont work already checked the fuses


double check fuses, sometimes hard to tell when they are blown, look at fuse menue to locate fuses for those functions and replace just to be certain

Mar 07, 2013 | Ford Mustang Cars & Trucks

1 Answer

A friend changed out the radiator on my 94 ford taurus & now the headlights wont work. what could have gone wrong?


He may have broken some wires or blown a fuse in the process, Check the fuse first then proceed by checking the wires from the headlight back into the harness (check the grounds as well). If you find any broken pinched or loose wires then you have found your problem. Repair it as neccesary and try the headlights again to see if they work. If the problem continues you may have to get a multimeter to test continuity from the fuse box to the headlights themselves, wires could be broken inside the insulation and not be noticable.

Sep 15, 2011 | 1994 Ford Taurus

1 Answer

The outside mirrors wont work they are power mirrors


In the fuse box located on the drivers side of the dash, check fuse # 25, should be a 10 amp (red) fuse. Check with a test light and with the ignition in the on position you should have power at both sides of the fuse. OR remove the fuse and see if the contacts in the middle are broken. Replace if blown.

Jul 31, 2010 | 2005 Jeep Liberty

1 Answer

Revere Polarity Jump Starting 92 LS400. Radio & More Wont Work


there are a few diodes in the electrical system that have been blown.  Some are in the dash and some are in the different control modules in the car.  Your insurance should pay for this problem.

Mar 26, 2009 | 1994 Lexus LS 400

1 Answer

Remove fuse 120a


You cannot change the fuse the way that you are trying. You need to loosen all of the bolts that holds the fuse box to the inner fender, and then observe the sides of the box, there are tabs that allow the exterior/bottom of the box to be pulled DOWN. After the box bottom is released, the 120 Amp fuse is accessible.
Hope this helps.

Dec 07, 2008 | 2004 Toyota Solara

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...