Question about Toyota Cars & Trucks

Open Question

2005 toyota camry air flow selector switch not working

Air flow selector switch not working

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: air flow selector

Your mode door is controlled by vacuum check the vacuum hose on the left side of the intake manifold. these some times fall off leaving your mode door with no vacuum and the default position of the mod door is defrost.

Posted on Jun 18, 2008

kn1ckfan
  • 8 Answers

SOURCE: HVAC vent selector does not function. Air flow is

THe blend door seems to be stuck. When you change settings from defrost to floor air or, vent, the blend door opens and closes directing the air to the place you want it to go to. I have had some success spraying a lubricating oil such as WD40 under the dash on the blend door. You need to get under the dash with a flashlight to locate it. It looks like a flap. Spray it with a couple of shots of the WD40. Go easy on the spraying as you may be inhaling the fumes. Keep the doors and windows open to minimize the fumes. Wait about 1/2 hour and try the A/C functions. (defrost, floor, vent air)

Posted on Mar 09, 2009

mrfrugal
  • 21 Answers

SOURCE: the selector switch for dash air ,floor air

Hi, sounds like a vacuum problem. When you select from floor to vent to defrost, the system uses vacuum from the engine to change over. If you look under the hood, near the firewall, towards the center, there should be small rubber vacuum lines. Check these lines for leaks with the engine on by spraying soapy water on the lines. If you see bubbles forming on any of the vacuum lines, this is where the leak is. Also check the vacuum lines going to the climate control unit inside the vehicle.

Posted on Jul 27, 2009

Murphybanton
  • 2004 Answers

SOURCE: water is seping into the car floorboard when I use

The AC hose that is suppose to drain water outside the car beneath is gone bad wherein water that is suppose to go outside the car is getting drained in the car and the front passenger side to be precise.

Trace the hose and reset it to flow out under the car.

Rate this.

Posted on Aug 11, 2009

  • 7353 Answers

SOURCE: 2001 Toyota camry 401 code came up. replaced the

egr position sensor. check items before you replace them, it gets expensive just guessing.

Posted on Oct 13, 2009

Testimonial: "thank you for the advise. and yes, it is getting expensive. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Camry's shift selector light problems


Make sure all your fuses are good and than you can take the molding off and see if the shifter indicator is broke wich is what i think it is, you would have to get a new one

Feb 28, 2013 | 2005 Toyota Camry LE

1 Answer

1997 toyota camry climate control switch or servo not working fully


Blend doors not working. They are controlled electronically by small motors. Could also be something fell down in a vent and is blocking it from it's full range of motion.

May 26, 2017 | 1997 Toyota Camry

2 Answers

2004 camry ac light blinking and throws hot air. Suggestions?


My 2003 Toyota Camry AC often starts blowing hot air and the AC light starts blinking. I don't know why the following process works, but it does. Using the temp selector (left) reduce the temperature all the way down to Max Cold and then push the Auto button. It will start blowing out very cold air. After a little while push the temp selector to the desired temperature.

Apr 03, 2012 | Cars & Trucks

1 Answer

Toyota 2000 camry fan only working on high speed


The blower motor resistor pack is defective and must be replaced. The resistor pack controls the variable speeds.

May 01, 2010 | 2000 Toyota Camry

1 Answer

Where is the neutral safety switch locayed at on


Where they all are on Toyotas - on the trans, mounted under the selector arm (the one that moves when you change gears.)

Nov 16, 2009 | 1995 Toyota Camry

2 Answers

2001 Toyota camry 401 code came up. replaced the


egr position sensor. check items before you replace them, it gets expensive just guessing.

Oct 13, 2009 | 2000 Toyota Camry

3 Answers

Code P0401 EGR Insufficient Air flow detected - 2000 Toyota camry


how I change the EGR valve assist switch for toyota camry 2000

Jul 29, 2009 | 1996 Toyota Camry

3 Answers

Stalling Toyota Camry 2004


P-0102 and P-0113 are mass air flow and intake air temp codes, the P-0136 is an Oxygen sensor code. Before you do anything, check for debris in the Mass Air Flow Sensor, it's small black box with electrical wiring connector that is screwed into the intake air tube, between the air box and the intake manifold. Undo the screws, remove the sensor, and, with a flashlight, and look down inside it for debeis, or broken wires inside it. If it's dirty, it could throw a P-0136...Comment back on what you find; hope this helps, and thanks for choosing FixYa!

Oct 24, 2008 | 2002 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...