Question about Cars & Trucks

1 Answer

Hearing draging noise coming frm brake pedal after I press brake an take off, noise goes away until I press brake again , is it the abs system or ??

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 47 Answers

You need to change your brakes they are consumed

Posted on Nov 25, 2013

  • 2 more comments 
  • Mario Nov 25, 2013

    I jus changed the pads..front an bk, I wonder is it like..the brake booster or...smthin with the ABS, eventhough I hav no light on the dash,

  • ahmad amireh Nov 25, 2013

    ok when you hit the brakes while driving dose the car kind of shake ?

  • Mario Nov 25, 2013

    No shaking at all truck rides smooth, 2day the brake pedal kind of pumped bk at me when in pressed it, dnt think it's the pads at all

  • Mario Nov 25, 2013

    I only hear it after I take off from a complete stop, like a dragging scraping sound coming from the brake pedal or under the dash

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Hissing noise when releasing brake pedal

Sounds like your brake booster but can't be sure until I know what kind of truck or car you have....

Posted on Jun 27, 2009

OneRide
  • 379 Answers

SOURCE: brakes feel spongy.when pressed hard goes nearly

Either you did not bleed the brakes properly or they need adjusted. (rear only) Front most likely are disks. If you put pads on the front and spread the caliper pistons, you should pump the brake pedal 10 or 15 times to move the pistons out. Some ABS systems are notoriously hard to bleed.

Posted on Jun 30, 2009

pippall
  • 1486 Answers

SOURCE: 2003 Prius: High pitched noise, ABS & BRAKE Lights on

Check your brake pads first,as they have a wear warning clip on them.so if you hear a loud screaming noise.Then its quite possible they have worn causing ur warning lights to come on.And i would get anouther quote as that is quite dear for a pump replacement.If it is the pump.good luck pippall!!

Posted on Jul 16, 2009

SOURCE: my brakes are making a hissing noise when i let

you mean you hear air in the cab down by the pedal. If thats the case your power steering assist is leaking. Its the big black unit behind the brake master cylinder. It may set a check engine light at times for lean condition.

Posted on Nov 19, 2009

  • 5467 Answers

SOURCE: on occasion front brakes staying engaged while

Well, guess I don't need to tell you this is dangerous and that your front Rotors are probably trashed.

This sounds like either a bad Master cylinder or a leaking Brake booster. There can also be a bad check valve on the Vacuum line plugging into the Brake booster. There is a rather large line with a plastic fitting, sometimes a 90 degree fitting on the end and the check valve is in the plastic

You can test the Brake booster with the engine running and using an approved Brake cleaner safe for rubber and plastics. Cover the outside bottom of the hood so spray does not get on your paint. Then spray around the Booster. If the engine RPM changes, you have a leak. Save the actuating rod, and replace the Booster. Spray the check valve, if RPM changes replace it.

Now for the Master cylinder, pressure gauges can be attached to the front fluid discharge to measure if the internal pistons are sticking. But you may spend more Labor in testing, than the part is worth.

My reasons for choosing these parts as defects are that your "Brake or ABS" warning lights are not on so the problem would be before those monitoring devices. The Vacuum system is not monitored and you hear hissing. The Master cylinder is not monitored before the ABS unit.

I hope you find my solution helpful.

Posted on Dec 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 Tahoe and recently the SERVICE STABILITY came on the dash board. It makes a real high pitched squealing noise while driving and it's now constantly making the noise. And getting worse. I know...


This stuff is my specialty, sounds like POSSIBLY your abs pump motor failing (the abs module mounts to the abs hydraulic pump where all the brake lines go into) i.e abs module=brain abs pump=muscle to put it simply. get the fault code(s), its going to be something like C0265 or C1214 basically "C" then 4 numbers. I can tell you EXACTLY what your problem is WITHOUT having to throw a bunch of money away by replacing unnecessary parts.
found this:
  • BRAKES - SQUEAK NOISE ON BRAKE PEDAL APPLICATION
TECHNICAL SERVICE BULLETIN
Bulletin No.: 08-05-22-002C
Date: April 07, 2009
Subject:
Squeak Noise On Brake Apply (Remove Brake Fluid from Master Cylinder and Refill)
Condition
Some customers may comment on a squeak noise when the brake pedal is applied or when released. This noise is normally heard when the brake pedal is slowly applied with the engine on or off, but can occur when the brake pedal is released. The noise may be isolated to the master cylinder area.
Correction
To correct this concern, remove as much of the old brake fluid from the master cylinder as possible and refill with a new DOT 3 brake fluid, P/N 88862806 (in Canada, use P/N 88862807). Start the vehicle and fully cycle the brake pedal until the noise diminishes to allow the new fluid to enter the system. hope this helps! -Tim

Jun 06, 2014 | Cars & Trucks

1 Answer

ABS light comes on and make noise


run diagnostic, check your wheel brg and rotor plate might hav cv grease on it also clean all sensors with brake cleaner

Feb 10, 2014 | 1999 Volkswagen Golf

1 Answer

Eb abs trouble


howdie sounds like their could be abs module week or you could have a sensor wire broke on one of the wheels, or the master cly could have a leak does the pedal come bk up right away?ck this out if not get a quote from your local garage its not good to mess around with brakes

Jul 24, 2012 | Ford Falcon Cars & Trucks

1 Answer

93 jaguar clicking sound when i press on the brake


Few latest troubleshooting help links related to these problem.
ABS light stays on but brakes work fine? http://howtobyme.blogspot.com/2011/11/abs-light-stays-on-but-brakes-work-fine.html

--------
Sometimes ABS light comes on while Driving?


http://howtobyme.blogspot.com/2011/12/sometimes-abs-light-comes-on-while.html

---------
Brake Fade Issue? http://whoisbyme.blogspot.in/2012/07/brake-fade-issue.html Brake System Troubleshooting? http://technoanswers.blogspot.com/2011/11/brake-system-troubleshooting.html Car Brake lines have no pressure? http://schematicsdiagram.blogspot.com/2011/12/car-brake-lines-have-no-pressure.html Car Brakes Dragging? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-dragging.html Car Brakes grabbing? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-grabbing.html Car Brakes Making Noise? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-making-noise.html Car Brakes Pulling? http://repairhelpcenter.blogspot.com/2011/12/car-brakes-pulling.html Pulsating Brake Pedal? http://repairhelpcenter.blogspot.com/2011/12/pulsating-brake-pedal.html Spongy brake pedal? http://repairhelpcenter.blogspot.com/2011/12/spongy-brake-pedal.html Hard Brake Pedal? http://repairhelpcenter.blogspot.com/2011/12/hard-brake-pedal.html Fading Sinking Brake pedal? http://whoisbyme.blogspot.in/2012/06/fading-sinking-brake-pedal.html Brakes make Grinding noise? http://repairhelpcenter.blogspot.in/2012/06/toyota-corolla-brakes-make-grinding.html

----------
These will help.
thanks.

Jul 07, 2012 | 1993 Jaguar XJ6

1 Answer

ABS light comes on intermitantly and when the brake pedal is pressed on you hear a noise like a humming..pedal jumps up...


CAR IS NOT SAFE TO DRIVE.SOUND LIKE YOU HAVE PROBLEM IN THE HYDRALIC MODULATOR SOLENOIDS IN THE ABS HYDRALIC MODULATOR UNIT.THE DEALERSHIP NEED TO CHECK AND FIX.WHEN WORKING WITH ABS BRAKE SYSTEM YOU NEED DIAGNOSTIC EQUIPMENT TO FIX ABS BRAKES.

Jun 03, 2011 | 2003 Buick Century

1 Answer

I have a dodge caravan that has the ABS and the BRAKE light on the pedal is rally hard but it goes away once in a while for like a day and all over again


Dodge used an ABS system for 2 years that didn't have a vacuum booster. Instead it used ABS pressure from the pump motor for the power brakes. This is the system you have. The ABS pump is mounted on top of the transmission. Is the pump running when the pedal is hard to push? Sometimes the pressure sensor in the ABS module will go bad and the pump won't run. You will get a hard pedal and the ABS light and the BRAKE lights will be on. The code in the ABS control module will be LOW BRAKE ACCUMULATOR PRESSURE.

Mar 04, 2011 | 1993 Dodge Caravan

2 Answers

When braking on my '04 Suburban, it pulsates like it has a warped brake rotor, but rotors are true (all four), and there is no correlating pulsation in the brake pedal, nor in the steering. Also, this...


Try pulling the fuse for the anti-lock braking system. If the problem goes away with the ABS disabled, check the wheel rotation sensors for problems, especially cracked or broken mounts or wiring issues. I'm thinking a sensor is dropping out when it gets heated by the brake and feeding bad data to the controller. The controller than treats it as a low traction situation and starts pulsing the brakes. If this is the case, you would see an ABS or Low Traction warning light on your dash.

Another possibility is a worn or loose suspension component oscillating under braking stress. In particular, check the shock absorber mounts. You could also have a pad that chatters instead of gripping the rotor cleanly - this may leave marks on the rotor, and would probably produce an audible noise.

Dec 23, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

1997 Audi A4 Brake Vibration


the only thing i can think of as a problem would be brake pad quality. i would get some from the dealer and fit them. if there is chatter going on it can also be caused by low quality rotors or a bad maching job. have them inspected for integrity.

Jan 28, 2010 | 1997 Audi A4

1 Answer

2006Vito.Bled all callipers now pedal drops underfoot


hi,replacing all brake pad are not required to bleed the brake system,brake pad goes in flooring because the system have air,abs system is out,try to bleed the system again,if not bring to your dealer,they have a bleeding machine,ty

Mar 22, 2009 | Mercedes-Benz CLK Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...