Question about 2006 Ford Focus

1 Answer

Will not start

When the key is turned in the ignition there are no ignition lights

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 108 Answers

What ignition lights? I didn't know it has any. Perhaps you are trying to use technical terms incorrectly? Does it make ANY sound when you turn the key to start?

Posted on Nov 24, 2013

  • Steve
    Steve Nov 24, 2013

    put the key into ignition and turn to ignition postion No ignitio lights turn a little moor to start and nothing happens no lights no clicking no nothing

  • dmhandyman Nov 28, 2013

    Okay, got it. Most people call those lights the idiot lights since a person needs some knowledge to read a guage, but no knowledge to see a warning light. The fact that NOTHING lights up says you have no voltage. Start at the battery and go toward the swith, checking to see where the voltage stops. Do the headlights light? If so, the problem is in the wiring to the switch.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My Cadillac cts 04 won't start... Every time I turn the key it won't even turn over... But the light that shows a car with a lock on it blinks what do I do


Sounds like the anti theft system is active m try this process. Turn the key on. Do not attempt to start. Wait 10 minutes. Turn key off. Turn key on. Wit for theft light to go off. Now attempt to start.

Oct 25, 2016 | Cadillac Cars & Trucks

1 Answer

Truck will not start, wait to start warning light is out?


Please provide more information.

"I put the key in the ignition, turn it and the warning light goes out, I turn the key to start but there is nothing..." or

"I put the key in the ignition, turn it and the warning light goes out, I turn the key to start but there only a ticking/clicking sound..." or

"I put the key in the ignition, turn it and the warning light goes out, I turn the key to start but the engine only turns over and doesn't catch."

Jan 06, 2015 | Cars & Trucks

1 Answer

Will not start but turns over


Check if security light is on, if so, must reset. To reset, put key in ignition and turn to on position. Security light will start flashing on and off. Leave key in on position until security light stops flashing and turns off completely. This will take approximately 10 minutes. Then turn key off and take out of ignition. Put key back in and start car. Should now start

Jun 29, 2014 | 2000 Saturn SL

1 Answer

2005 ford 500, won't start a lock light is


need to reprogram ignition key security system when battery disconnected. turn ignition key to the on position for 3 to 10 seconds until the lock light goes out then start vechicle.if lock light dont turn off turn ignition switch to on position 30 seconds until lock light turn off.

Jun 12, 2013 | Cars & Trucks

3 Answers

We bought a new ignition switch for the key not coming out of the ignition but when we installed the new switch the car wouldn't start...is there a step that we're missing? (2004 Aztek)


Hello: TRY THIS Attempt to start the car leave the key on for 10 minutes or until the security light goes out, at this time turn key off for 10 seconds, turn switch on for ten more minutes or when security light goes out, turn key off for 10 seconds. Turn key ON for ten minutes or when security light goes out, turn key off wait 10 seconds, then start car....

Jul 31, 2011 | 2004 Pontiac Aztek

2 Answers

Car was stolen ignition was ripped out of 2002 grandam, now car won't start with ignition and security light keeps flashing


groan.....gunna need a bit more info. but i'll try. What portion of the ignition was ripped out? The tumbler + switch? If so, you might need to get the car's system resent to recognize that it has a new ignition put in. Sime vehicles have a theft prevention system in place to prevent the vehicle from running if its been hot wired. Your best bet would be to replace the damaged ignition components (You did not mention if you did or not). If it still doesn't work after you have replced all of the ignition components. You can try to reset the vehicle (doesn't work on all) disconnect negative battery terminal and go back into vehicle and press down the brake pedal for about 30 seconds then reconnect battery and try it....good luck, hope this helps

Aug 17, 2009 | 2002 Pontiac Grand Am

3 Answers

Ignition key wont turn


is it correct key? key and ignition barrel could be worn wiggle key around in ignition while turning? gently but fast wiggling.try lube in key slot also.
if not replace barrel and key

May 31, 2009 | 1995 Toyota Camry

1 Answer

How do I program my key for my 2006 Chevy Impala?


Add Duplicate Key (PK3 or PK3+ key)
1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.
Originate New Master Key (PK3 or PK3+ key)

1. Insert new key into ignition cylinder and turn it to the ON (RUN) position.
The security light on the dash will illuminate and stay on for ten minutes.
2. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back to the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
3. When the security light goes out, you have one minute to start the next
step. Turn the ignition cylinder to OFF and then back on the ON (RUN)
position. The security light on the dash will illuminate and stay on for ten
more minutes.
4. After the security light has gone off the third time, the key has been programmed
into the vehicle’s computer and will operate the car. It has replaced ALL the
previous electronic key codes and is the ONLY key programmed into the
vehicle’s computer.

Add Duplicate Key (PK3 or PK3+ key)

1. Insert an existing key into the ignition cylinder.
2. Turn the ignition cylinder to ON (RUN) and back to OFF.
3. Remove the existing key and, within fifteen seconds, insert the new key
and turn it to ON (RUN).
4. The security light will light up for two seconds to indicate success in programming
the key into the vehicle.

May 20, 2009 | 2006 Chevrolet Impala

1 Answer

Redo code for 2007 Pilot key


ok get in the car, close the door, make sure all doors are closed.... put the key in the ignition, turn the key to on but without starting the car (lights on dash light up only) press and release the key lock button, turn key to off, without removeing the key.. turn to on without starting the car (dash lights up only) press and release the key lock button again, turn the ignition off, without removeing the key then turn back on (lights on dash on only without starting the car, press and release the key lock button , turn off the ignition without removeing the key, ..turn on the ignition once more without starting the car , press and release the key lock button and u should hear the door lock cycle ....leave the key in the ignition ... now press the lock button or unlock button on the other remotes one at a time if u have them.....u should hear the lock cycle indicateing all remotes are programmed.... kind of tricky to explain but you will get it, the sequence of turnin the key in the ignition on and off is only done with that one first key,,, remember after the door lock cyles press the lock or unlock button on the other remote fobs if if any...and ur done..may take u a few trys.. let me know how it worked out.

Apr 06, 2009 | 2007 Honda Pilot

2 Answers

Won't turn over , security light comes on when trying to start,


try puting te ignition key in the drivers door lock an unloack it 3 or 4 times then try agin if it dosnt work, key needs reprormming

Mar 18, 2009 | 1993 Buick LeSabre

Not finding what you are looking for?
2006 Ford Focus Logo

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...