Question about Ford Focus

Open Question

Replaced front oxygen sensor engine light light still on

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
txkjun
  • 409 Answers

SOURCE: check engine light come on fault codes PO165 and PO155

Yes sorry but they both should be replaced. 

Posted on Dec 26, 2008

Ad
Hightower971
  • 183 Answers

SOURCE: Engine warning light indicating oxygen sensor

Because there are 4 of them.

Posted on Apr 26, 2009

ghassun
  • 499 Answers

SOURCE: check engine light is on...bank 1 sensor1 oxygen sensor

if u have one oxygen sensor then u need to take a deep look at the bottom of ur car it will be somewhere at the Exhaust pipe if u have a catalytic converter then u will have two oxygen sensors one before the catalytic converter & the other will be after the catalytic converter. Note: the catalytic converter is located at after a little bit of beginning in Exhaust pipe.

Posted on Jun 06, 2009

mkv0525
  • 358 Answers

SOURCE: fault code 0135 front heater oxygen sensor causing

need to replsce the sensor.

Posted on Jun 12, 2009

Molson02536
  • 3854 Answers

SOURCE: Oxygen sensor replacement

It's something you can with simple tools, you have four O2 sensors. Your going to have to get the truck rescanned or if you have the DTC code, you can find out which O2 sensor has gone bad so you can replace it. Your going to have Two upstream O2 sensors on each exhaust bank, one O2 sensor before the Catalytic Converter, and the last one after the Catalytic Converter. Its like replacing a Spark plug and you can pick up the O2 sensor at any large Auto Parts store with a can of WD 40. Just unclip the wire leads to the O2 sensor and then with a O2 sensor socket or hint close end wrench and hammer, you can remove the O2 sensor from the exhaust pipe. Good luck and be safe.

Posted on Nov 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

0152 coed


P0152 P0152 - O2 Sensor Circuit High Voltage Bank 2 Sensor 1Possible causes - Faulty Front Heated Oxygen Sensor Bank 2
- Intake air leaks may be faulty
- Exhaust gas leaks
- Front Heated Oxygen Sensor Bank 2 harness is open or shorted
- Front Heated Oxygen Sensor Bank 2 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
eplacing the Front Heated Oxygen Sensor Bank 2 usually takes care of the problem
Symptoms- Engine Light ON (or Service Engine Soon Warning Light)
- High Fuel Consumption
- Excessive Smoke from Exhaust P0152 Description The front heated oxygen sensor (or O2 sensor 1) is placed into the exhaust manifold. It detects the amount of oxygen in the exhaust gas compared to the outside air. The heated oxygen sensor 1 has a closed-end tube made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. The heated oxygen sensor 1 signal is sent to the Engine Control Module (ECM). The ECM adjusts the injection pulse duration to achieve the ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical change from 1V to 0V.

Mar 19, 2013 | 2005 Dodge Ram 1500

1 Answer

2005 aveo code po132


There is not cut and dry solution for this code, here are the possibility's
P0132 - O2 Sensor Circuit High Voltage Bank 1 Sensor 1 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- High Fuel Consumption
- Excessive Smoke from Exhaust Possible causes - Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Feb 14, 2012 | Chevrolet Aveo Cars & Trucks

2 Answers

Check Engine light with Po131 o2 circuit low voltage sensor 1 bank 1 reading, what does that mean?


- Front Heated Oxygen Sensor Bank 1 harness is open or shorted
- Front Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Faulty Front Heated Oxygen Sensor Bank 1
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

Replacing the O2 Sensor 1 usually takes care of the problem

The front heated oxygen sensor (or O2 sensor 1) is placed into the exhaust manifold. It detects the amount of oxygen in the exhaust gas compared to the outside air. The heated oxygen sensor 1 has a closed-end tube made of ceramic zirconia. The zirconia generates voltage from approximately 1V in richer conditions to 0V in leaner conditions. The heated oxygen sensor 1 signal is sent to the Engine Control Module (ECM). The ECM adjusts the injection pulse duration to achieve the ideal air-fuel ratio. The ideal air-fuel ratio occurs near the radical change from 1V to 0V.

Feb 07, 2012 | 2004 Honda Odyssey

1 Answer

My 2000 Cadillac Deville engine light on. Engine code PO420


Catalyst System Efficiency Below Threshold (Bank 1)

A code PO420 may mean that one or more of the following has happened:
  • Leaded fuel was used where unleaded was called for
  • An oxygen sensor is not reading (functioning) properly
  • The engine coolant temperature sensor is not working properly
  • Damaged or leaking exhaust manifold / catalytic converter / exhaust pipe
  • Retarded spark timing
  • The oxygen sensors in front and behind the converter are reporting too similar of reading

  • Check for exhaust leaks at the manifold, pipes, catalytic converter. Repair as required.
  • Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
  • Inspect the downstream heated oxygen sensor (HO2), replace if necessary
  • Replace the catalytic converter

May 11, 2011 | 2000 Cadillac DeVille

1 Answer

What is p1148


P1148 - Closed Loop Control Function Bank 1
This mean that the closed loop control function for bank 1 does not operate even when vehicle is driving in the specified condition.

The Powertrain Control Module (PCM) or Electronic Control Module(ECM) monitor the function of the Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor by comparing the signal with the Rear O2 sensor.

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes:
- Harness or connectors Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor 1 circuit is open or shorted.
- Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor bank 1
- Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor bank 1 heater

Possible solution:
- Repair harness or connector. If repair is needed
- Replaced Front Oxygen (O2) sensor or Air/Fuel (A/F) sensor bank 1


Then, possible causes are faulty harness or connectors to the air fuel ratio sensor, a faulty air fuel ratio sensor (1) or faulty air fuel ratio sensor (1) heater. Most likely yes it is just faulty sensor. Just replace this devices and reset the stored codes.

Keep us updated.

Feb 10, 2011 | 2005 Nissan Altima

2 Answers

How many 02 sensors does a 2003 GMC Envoy have check engine light is on we have replaced 2 02 sensors like it first told us


A "V" configuration engine, (8 or 6), uses two upper oxygen sensors and either 1 or 2 lower oxygen sensors.
If the vehicle has dual exhaust; dual all the way from the front to the end of the tailpipe, the vehicle will also have two LOWER sensors. But if the two exhaust manifolds converge into one tailpipe, you likely only have 1 lower oxygen sensor.
Check the electrical connections on the new oxygen sensors, and make certain that you have replaced your old sensors with the right type.

Aug 30, 2010 | 2003 GMC Envoy

3 Answers

Were on exaust is oxygen sensor in 1999 subaru impreza auto sport


On the SOHC engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the front catalytic converter. On the DOHC engine the front oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the catalytic converter.

Oxygen sensor location-Baja 2.5L SOHC engine
c3fce0b.jpg

Oxygen sensor location-Baja 2.5L DOHC engine
7aac75e.jpg


On the 2.0L engine the front (A/F) oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the rear catalytic converter. On the 2.2L engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the rear catalytic converter.

Oxygen sensor location-Impreza 1998-2001 2.2L engine
a5973e4.jpg


moz-screenshot.pngOxygen sensor location-Impreza 1998-2002 2.5L SOHC engine
3a84717.jpg
I hope helped with this; remember rated this help. Good luck.

Nov 20, 2009 | 1999 Subaru Impreza

1 Answer

PO420


Not just a faulty catalytic converter will trigger this code. Many other issues can trigger this code.

  • Leaded fuel was used where unleaded was called for
  • An oxygen sensor is not reading (functioning) properly
  • The engine coolant temperature sensor is not working properly
  • Damaged or leaking exhaust manifold / catalytic converter / exhaust pipe
  • Delayed spark timing
  • The oxygen sensors in front and behind the converter are reporting too similar of readings
Possible solutions:
  • Check for exhaust leaks at the manifold, pipes, catalytic converter.
  • Replace Coolant Temperature Sensor
  • Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
  • Inspect the downstream heated oxygen sensor (HO2)
  • Replace the catalytic converter
  • Have timing adjusted


Aug 25, 2009 | 2002 Toyota Camry

1 Answer

Engine code p0421


Catalyst System Efficiency Below Threshold (Bank 1)

The catalytic converter has an oxygen sensor in front and behind it. When the vehicle is warm and running in closed loop mode, the upstream oxygen sensor waveform reading should fluctuate. The downstream O2 sensor reading should be fairly steady. Typically the P0420 code triggers the Check Engine Light if the readings of the two sensors are similar. This is indicative of (among other things) a converter that is not working as efficiently as it should be (according to specs). It is part of the vehicle emissions system.

A code P0420 may mean that one or more of the following has happened:

* Leaded fuel was used where unleaded was called for
* An oxygen sensor is not reading (functioning) properly
* The engine coolant temperature sensor is not working properly
* Damaged or leaking exhaust manifold
/ catalytic converter / exhaust pipe
* Retarded spark timing
* The oxygen sensors in front and behind the converter are reporting too similar of readings


To Do list

* Check for exhaust leaks at the manifold, pipes, catalytic converter. Repair as required.
* Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
* Inspect the downstream heated oxygen sensor (HO2), replace if necessary
* Replace the catalytic converter

Jan 04, 2009 | 2001 Hyundai Sonata

1 Answer

Xterra repair


Since this is an intermittent problem, first try to determine if the problem arises due to one of these many intermittent problems:

* Vehicle vibration
* Heat sensitive
* Freezing
* Water intrusion
* Electrical load
* Cold or hot start up

If you can't isolate the cause of the intermittent problem, you can try adjusting the Idle Speed/Ignition Timing/Idle Mixture Ratio:

Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment

PREPARATION
1) Make sure that the following parts are in good order.

* Battery
* Ignition system
* Engine oil and coolant levels
* Fuses
* ECM harness connector
* Vacuum hoses
* Air intake system
* (Oil filler cap, oil level gauge, etc.)
* Fuel pressure
* Engine compression
* EGR valve operation (If so equipped)
* Throttle valve
* Evaporative emission system

2) On air conditioner equipped models, checks should be carried out while the air conditioner is OFF.
3) On automatic transmission equipped models, when checking idle rpm, ignition timing and mixture ratio,
checks should be carried out while shift lever is in “N” position.
4) When measuring “CO” percentage, insert probe more than 40 cm (15.7 in) into tail pipe.
5) Turn off headlamps, heater blower, rear defogger.
6) Keep front wheels pointed straight ahead.
7) Make the check after the cooling fan has stopped.

INSPECTION PROCEDURE

1 INSPECTION START
1. Visually check the following:
I Air cleaner clogging
I Hoses and ducts for leaks
I EGR valve operation (If so equipped)
I Electrical connectors
I Gasket
I Throttle valve and throttle position sensor operation
2. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
3. Open engine hood and run engine at about 2,000 rpm for about 2 minutes under no-load.
4. Perform diagnostic test mode II (Self-diagnostic results).
OK or NG
OK ' GO TO 2.
NG ' 1. Repair or replace components as necessary.
2. GO TO 2.

2 CHECK IGNITION TIMING
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Turn off engine and disconnect throttle position sensor harness connector.
4. Start and rev engine (2,000 - 3,000 rpm) two or three times under no-load, then run at idle speed.
5. Check ignition timing with a timing light.
15°±2° BTDC (in “P” or “N” position)
OK or NG
OK ' GO TO 4.
NG ' GO TO 3.

3 ADJUST IGNITION TIMING
1. Adjust ignition timing by turning distributor after loosening securing bolts.
2. Turn off engine and connect throttle position sensor harness connector to throttle position sensor.
' GO TO 2.


4 CHECK BASE IDLE SPEED
1. Check idle speed.
700±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 6.
NG ' GO TO 5.

5 ADJUST BASE IDLE SPEED
1. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run engine at idle speed.
2. Adjust idle speed by turning idle speed adjusting screw.
700±50 rpm (in “P” or “N” position)
' GO TO 6.

6 CHECK TARGET IDLE SPEED
1. Turn off engine and connect throttle position sensor harness connector.
2. Start and rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run at idle speed.
3. Check idle speed.
750±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 9.
NG ' GO TO 7.

7 DETECT MALFUNCTIONING PART
Check the following.
1. Check IACV-AAC valve and replace if necessary.
2. Check IACV-AAC valve harness and repair if necessary.
3. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 9.

9 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
3. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 12.
NG (MIL does not blink.) ' GO TO 17.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.


10 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 13.
NG ' GO TO 11.

11 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit.
Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.


13 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
2. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG (MIL does not blink.) ' GO TO 16.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor RH.
2. GO TO 14.


14 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG ' GO TO 15.

15 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit. Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.
16 CHECK FRONT HEATED OXYGEN SENSOR RH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor RH harness connector.
4. Check harness continuity between ECM terminal 50 and front heated oxygen sensor RH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

17 CHECK FRONT HEATED OXYGEN SENSOR LH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor LH harness connector.
4. Check harness continuity between ECM terminal 51 and front heated oxygen sensor LH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

18 PREPARATION FOR “CO” % CHECK
1. Disconnect engine coolant temperature sensor harness connector.
2. Connect a resistor (4.4 kW) between terminals of engine coolant temperature sensor harness connector.
' GO TO 19.

19 CHECK “CO” %
1. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Check “CO” %.
Idle CO: 1.5 - 9%
After checking CO%,
a. Disconnect the resistor from terminals of engine coolant temperature sensor.
b. Connect engine coolant temperature sensor harness connector to engine coolant temperature sensor.
OK or NG
OK ' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.
NG ' GO TO 20.

20 DETECT MALFUNCTIONING PART
Check the following.
1. Connect front heated oxygen sensor harness connectors to front heated oxygen sensors.
2. Check fuel pressure regulator.
3. Check mass air flow sensor and its circuit.
4. Check injector and its circuit.
Clean or replace if necessary.
5. Check engine coolant temperature sensor and its circuit.
6. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.

Aug 17, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...