Question about Cars & Trucks

Open Question

--code f21 on a Siemens WM12E468GB/07 washing machine

Is not working due to fault code flashing

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

?JCB FAULT CODES LIST


P0087 (flashing code 227) shared sump low pressure fault (for pump without pressure supply)
The main fault symptoms
• Engine severe vibration.
• idling unstable
• Output Fall
• exhaust smoke
• It may be too large output
P0088 (flashing code 118) shared the tank pressure is abnormally high (first or second stage)
The main fault symptoms
• Engine severe vibration
• idle instability
• Output Fall
• channeling gas engine failure
• exhaust smoke
• It may be too large output
P0089 (flashing code 151) shared the tank pressure failure (for pump pressure supply is too large)
The main fault symptoms
• Engine severe vibration
• idle instability
• Output Fall
• channeling gas engine failure
• exhaust smoke
• It may be too large output
P0090 (flashing code 247) SCV drive system open, + B short circuit or shorted to ground
The main fault symptoms
• Depending on the open / short situations, there may be an engine stall and / or launch
Machine channeling gas.
• exhaust smoke
• Output is too large
P0107 (flashing code 71) atmospheric pressure sensor circuit input low (open or shorted to ground)
The main fault symptoms
Due to spare the equivalent altitude 2000 m (6562 ft)
• exhaust smoke at high altitude.
• insufficient output at low altitude
P0108 (flashing code 71) atmospheric pressure sensor circuit input high (+ 5V shorted)
The main fault symptoms
Due to spare the equivalent altitude 2000 m (6562 ft)
• The high altitude exhaust smoke
• lack of low altitude output
P0112 (flashing code 22) intake air temperature sensor fault (low voltage fault, earth fault, short circuit)
The main fault symptoms
• When cold starting, may exhaust white smoke.

More here http://truckmanual.weebly.com/jcb-fault-codes.html

on Dec 20, 2016 | Cars & Trucks

1 Answer

What is the fault when the air bag dash light flashes code 49


It's a common fault on many Fords, usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat. Just push it together properly and it should clear the fault. If not, go under the drivers seat and secure all the wires and clips there as well.

Aug 21, 2014 | 2006 Ford Territory 4.0

1 Answer

What is the meaning of fault code 0837


This will help:

http://search.aol.com/aol/search?&s_qt=sb&q=Auto+fault+code+0837&tb_oid=07-01-2013&s_it=amonetizetest1-ie&tb_mrud=07-01-2013&tb_uuid=20130107163427450

Jan 20, 2013 | 2002 Jeep Grand Cherokee

1 Answer

Flashing overdrive light


The overdrive light is flashing due to a fault within the transmission. A scan tool is needed to retrieve the codes to see what part of the transmission has a fault.

Jan 15, 2013 | 1997 Ford Explorer AWD

3 Answers

Check engine light just came on 1993 toy camry


First you need to find out what the fault code is that is making the check engine light come on. To do this, locate the diagnostic connector under the hood. It will be a black rectangular connector approx 50mm X 25mm with Diagnostic written on the cover. Open the cover and on the inside of the cover will be a diagram of the connections and their different labels. Locate pins labelled TE1 and E1. Switch on the ignition switch without starting the engine and with a small jumper wire bridge between pin TE1 and pin E1. Observe the check engine light on the dash and you will notice that it will be flashing. Read the diagnosis code as indicated by the number of flashes that this light makes. Each code will be displayed by first blinking the first digit of the code, then a pause and blink the second digit of the code. For example, Code 52 (knock sensor signal) will flash 5 times, pause and then flash 2 times, then a longer pause before it goes onto the next fault code if there is another one. Once it has gone through all the stored fault codes it will go through the sequence again starting at the first fault code again. Due to the many different fault codes that can be obtained it would be better to post another question for the fault code obtained. Good luck!

Jan 06, 2010 | 1993 Toyota Camry V6

1 Answer

Air bag light is and flashing code 27


This is a common fault on FORD
 
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.
 
 
Just push it together properly and it should clear the AirBag fault light 
 


Jan 05, 2010 | 2004 Ford F350

1 Answer

07 Tahoe 85,000 miles - the check engine light will come on for a couple of days then go off for a couple of days. Put it on a machine and nothing is wrong but the light will not stay off. Want to sell it...


Try replacing the o2 sensor in the exhaust header or the cat pipe.

It is probably an intermittent fault in this sensor that clears itself due perhaps to chafed cables or a bad plug connection hence no codes are stored.

Oct 23, 2009 | Chevrolet Tahoe Cars & Trucks

1 Answer

Airbag dash light flashing code 51


Common fault on FORD

Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.

Just push it together properly and it should clear the AirBag fault

May 18, 2009 | 2003 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...