Question about Porsche Cars & Trucks

Open Question

My clutch pedal is too deep to the floor, how to adjust?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jocko777
  • 7 Answers

SOURCE: Low / Soft Clutch Pedal, 1995 Rodeo 2W 2.6L

at a minimum the pressure plate but not changing everything while in there would be silly

Posted on Aug 01, 2008

Ad
  • 1 Answer

SOURCE: clutch pedal stuck to the floor

hi, there is one place you should check. but answer this first, did you swap the car with a new engine or did you pull the engine out of the car? if the anwser is "yes" then you'll probably twist a fluid tube for the clutch at the tranny. so check the front end of the tranny, it should be a short metal wire (tube like) that should be connection to the tranny. the bolt size is 8mm. so find that tube and open the line. then ask someone to pump the clutch pedal 3 or 4 time and stop while holding it down. yes! the clutch fluid should be coming out while he's doing that. so now when he's press down the last pump, you should twist it back on. repeat it, over and over until you get it to harden again. you should also open the clutch master cylinter, too and refill some more... well hope this help...

Posted on Dec 10, 2008

  • 566 Answers

SOURCE: Clutch pedal low near floor, can the clutch be adjusted?

hi the clutch on accent is hydraulic operation so if pedal is very low on disengaging clutch ? you may have a problem with the hydraulics 1st thing to check is fluid level? this is the reservoir that feeds both brakes and clutch but is seperaterated inside if fluid low? top up and bleed the slave cyl however if fluid low indicates a leak ? possibly slave cyl? if no loss of fluid ? then prob may be fault in the master cyl ? check fluid come back with any update please ps if this problem has just occured? check for leaks ?

Posted on Feb 02, 2009

emissionwiz
  • 76132 Answers

SOURCE: Clutch pedal stays on floor

the problem is that either the master or slave cylinder for the hydraulic clutch have failed, it is always recommended that they both replaced together, u can bleed the clutch but the problem will occur again.

Posted on May 07, 2009

BCAS1298
  • 3092 Answers

SOURCE: clutch pedal goes to floor and stays 1999 Nissan

ON A 2000 MAX 6 CYLINDER HAS CLUTCH MASTER CYLINDER AND SLAVE CYLINDER, CHECK FLUID LEVEL AND BLEED CLUTCH SYSTEM AT SLAVE CYLINDER BLEEDER. HAVE NOT HEAR OF CABLE CLUTCH SYSTEM. ONLY HYDO.& LINKAGE. GOOD LUCK

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to adjust the clutch on a 1999 Ford escort ZX2


The clutch is not adjustable it is fully hydraulic. That means it is self adjusting, if the clutch pedal engages high on the pedal and the clutch is hard to push you need a new clutch plate and pressure plate.

Mar 18, 2017 | 1999 Ford Escort

1 Answer

What can I do to adjust clutch cable on my 1989 LeBaron?


Just push and then lift the clutch pedal toward you to adjust the cable. The mechanism is above the clutch pedal and is selfadjusting as liong as you lift the pedal. If that don't work then the adjust mechanism is junk.

May 01, 2014 | 1989 Chrysler LeBaron

1 Answer

How to adjust 95 geo tracker clutch


engaging?
you meant dis-engage im sure.
pedal up is engaged,
pedal at floor dis-engages it.
my guess, is the clutch drags unless i push the clutch pedal 100%
to the floor.
1: bad cable is 90% cause. non last this long.
2: no free play is way too loose.
3: broken lever on the pedal top. caused by #1

all fail modes covered here.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Apr 23, 2014 | Geo Tracker Cars & Trucks

2 Answers

My clutch is barely engaging even when depressed all the way to the floor. Can it be adjusted or dose it need a clutch replacement?


I would try adjusting the clutch master such that the point of engagement at the pedal, is further from the floor. This will effectively increase the travel of the clutch slave and possibly solve your problem. The clutch master pushrod should have an adjustment behind the pivot at the pedal bracket. Usually a lock nut has to be loosened off a little and then the rod screwed out of it's holder to effectively lengthen it.

Jan 24, 2011 | 1999 Suzuki Grand Vitara

1 Answer

Is the clutch adjusted by a cable? If so, how?


Nope, there is an automatic adjustment device at the clutch pedal. If the clutch only operate when the pedal is near the floor and you have about 150000 km you might need a new clutch.check the device at the pedal first for broken teeth, otherwise replace the clutch including the clutch bearing

Jan 30, 2010 | 1993 Ford Escort 4 Door

1 Answer

How to adjust clutch brake on a eaton 2800 series clutch which is installed in a 2004 sterling dump truck


This is from http://refrigeratedtrans.com/mag/transportation_replace_original_equipment/

"A good clutch adjustment begins by identifying the location of the bearing. It should be positioned 1/2" to 9/16" from the clutch brake."

"After the bearing is set, adjust the truck linkage to allow the clutch brake to squeeze a .010" feeler gauge between the bearing and clutch brake when the pedal is no more than 1" to 1.5" from the floor. Setting the clutch brake position too far from the floor reduces the stroke to the clutch and could cause release problems and reduce brake life.
All that remains is checking the free-pedal distance in the cab. With the pedal in the up position, there should be 1" to 3" of free pedal. The clutch is now adjusted correctly."

Apr 21, 2009 | 2004 Ford Super Duty F 450

1 Answer

Can't push clutch pedal with key 'on'; key 'off' the pedal moves.


Try this site:
http://faculty.ccp.edu/faculty/dreed/Campingart/jettatech/index.htm

You might be able to find an answer there.
Otherwise try the search engine in here:
http://tech.bentleypublishers.com/forum.jspa?forumName=volkswagen.a.a3

Feb 16, 2009 | 1997 Volkswagen Jetta

2 Answers

Clutch slipping


first i would try adjusting the clutch cable because commonly people with think that they're clutch is going out when really just the cable has gotten stretched....try adjusting that first and if that works then you should be fine for another couple thousand miles but if you want to not have to worry bout it for awhile i would just replace teh clutch assembly....usually ranges from $200 to $450 depending on the clutch set and the mechanic that does the work for you. Let me know what happens. :)

Oct 01, 2008 | 1990 Peugeot 405

2 Answers

Clutch check


you have civic SI type R with the K20A engine and 6sp transmission? correct?

yes the clutch is adjustable.

  1. loosen the clutch pedal position switch(lower of the 2 switches) locknut and back off the clutch pedal position switch.
  2. loosen the clutch push-rod locknut and turn the push-rod in or out to get the desired height and stroke of the pedal.
  3. tighten the push-rod locknut
  4. with the clutch pedal released, turn the clutch pedal position switch in until it contacts the clutch pedal.
  5. turn the clutch pedal position switch in an additional 3/4 to 1 turn.
  6. tighten the clutch pedal position switch locknut.
  7. loosen the clutch interlock switch(the upper switch) locknut and then the interlock switch.
  8. press the clutch pedal to the floor.
  9. release the pedal about 1/2 in. from the fully depressed position, and hold it there. adjust the position of the interlock switch so that the engine will start with the clutch pedal in this position.
  10. tighten the interlock switch locknut.
clutch pedal stroke should be: 5.1 - 5.5 in
clutch pedal height should be: 7.76 in

if adjusting the clutch doesn't help with the transmission feeling notchy, may be the syncros.




Jul 09, 2008 | 2002 Honda Civic

2 Answers

Front wheel Drive query


DEar Customer,

your from is that your car is front wheel drive & you have to reset your car clutch point that loose its sensitivity as they had before,

its not a big prib you have to open bonet than make more active clutch wire with streching clutch joints.

THNX

May 17, 2008 | 1991 Peugeot 405

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

309 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

902 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...