Question about Cars & Trucks

Open Question

Dt466 flywheel bolt torque - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

Ad
  • 375 Answers

SOURCE: Flywheel bolts torque settings

Check with your local auto parts store. Or buy a repair manual

Posted on Jul 01, 2008

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

REDOIL
  • 355 Answers

SOURCE: what are the torque specs on the flywheel bolts

well is this a stick or rring gear any way if this is a stick 60 foot lbs left of car you start center is one then the top would be six and the bottom one is 3 right sude is center is two upper is five and lower is four this is toq patern hope this helps redoil

Posted on Aug 06, 2009

morse008
  • 1111 Answers

SOURCE: I need torque settings for 1600 beetle engine SP

wiki this

Posted on Aug 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

Torque spec's for the fly wheel


Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Cars & Trucks

1 Answer

What is the torque setting for nissan navara v6 4lt2007 flywheel torque


there are 2 sets of torque specs for flywheel bolts as there are 2 different fly wheels in use with different bolts for each
go google and type in--torque specifications for nissan navara flywheel bolts and fins a site relevant to you application
it could be 61-69 ft/lbs a or 90 ft lbs depending on the flywheel and the vehicle 2wd or 4wd

Sep 30, 2015 | Nissan Cars & Trucks

1 Answer

How i can find the horsepower of a DT466


From the factory the DT466 could be purchased in trucks with HP options up to 250-275 HP. If you choose to increase much more than that you will start to have some reliability issues.

How much you can increase depends on several isses.

The more you increase the HP the greater your cooling needs will become, especially on an uphill grade. Inceasing your HP 20% may require 100% increase in cooling capacity. Marine applications don't count because keel coolers have the whole ocean for heat exchange.

The ease of increase depends upon which pump you have. The electronic pump is a software upgrade. Inline mechanical pumps are easier to increase than the mechanical rotary type pump.

Depending on what transmission you have behind your DT466 will also determine how much of an increase in HP you can use. 250-275 HP is about the limit for MT-series Allison transmissions. More than that you will need the HT-series if you want reliability.

Stick shifts will be limited to the size of the clutch. Much more than the 250-275 HP range will require a larger clutch which may require a different flywheel.

If you have repowered a truck that didn't have the DT466 in it from the factory, increasing the HP can also cause driveline and chassis problems. The most signigicant would be the driveshaft may not be able to handle the increased HP and torque, particularly on a downshift while going uphill. You may also experience frame torque causing on starts and shifts causing your frame to crack or break.

Jan 11, 2015 | Cars & Trucks

2 Answers

How many ft/lbs of torque is recommended on the flywheel bolts when installing the flywheel on a 1996 GMC Sierra Z-71 4x4 5.7L engine?


GMC Sierra Bolt Torque Specifications. ... The torque converter bolts to the flywheel with 46 foot-lbs. of torque. ... 1996 GMC Sierra Horsepower Torque Specs.

May 02, 2014 | Cars & Trucks

1 Answer

1997 jeep wrangler 6 cylinder flywheel torque


It depends on what you are calling "flywheel". If it is a manual transmission, the vehicle is equiped with a true "flywheel", if it is equipped with an automatic transmission, it is equipped with a "flex plate" which a lot of people refer to as a flywheel.

With that said the torque specs are:
Flywheel-to-crankshaft bolts - 105 Ft. Lbs (142 N.m)
Flexplate-to-crankshaft bolts - 55 Ft. Lbs (75 N.m)

May 14, 2012 | Jeep Wrangler Cars & Trucks

1 Answer

2001 tiburon


Torque converters are bolted up to the flywheel or flexplate. Probably 4 or 6 bolts from the flywheel engine side into the torque converter.

May 03, 2012 | 2001 Hyundai Tiburon

1 Answer

Flywheel keeps breaking on 1994 4x4 explorer


TRANSMISSION FLYWHEEL HAS TO ALIGN CORRECTLY.MAKE SURE FLYWHEEL IS IN THE ALIGNMENT DOWEL BOLTS TIGHTEN IN SEQUENCE IF NOT FLYWHEEL THATS NOT ALIGN CORRECTLY WHEN YOU TIGHTEN IT UP IN A BIND FLYWHEEL WILL CRACK.MAKE SURE FLYWHEEL TORQUE IS 59 FT LBS FOR THE 4.0 ENGINE.THE 5.0 ENGINE FLYWHEEL BOLTS TORQUE IS 75 - 85 FT LBS.IF OVER TIGHTEN FLYWHEEL IT WILL CRACK IT.

Jul 25, 2011 | Ford Explorer Cars & Trucks

1 Answer

How do you change the flywheel?


Pull the transmission back (or remove) enough to access the flywheel/ torque converter. Remove the converter from the flywheel, then you will see the flywheel bolts that mount the flywheel to the crankshaft--(I think there are 6). It is advisable to replace these bolts with new ones when reinstalling the flywheel, and be sure to get the proper torque spec for the bolts from autozone or a reputable shop and torque them sequencially correct and to the proper spec.

Oct 03, 2010 | 1982 Chevrolet El Camino

1 Answer

Bolt torque settings for fixing flywheel and torque convertor into GM700r4 gearbox. cheers


flywheel bolts m8 torque to 65-70 ft lbs in america so take that and do a convert eh and torque convertor bolts chek too 20 no more!!

Jan 15, 2010 | 1984 Chevrolet Chevy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,041 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...