Question about 2012 Kia Soul Base Wagon 1.6L 4-cyl. 6-speed Manual

Open Question

Remove rear bench kia soul

Putting on seat covers. need to remove the rear bench to secure.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jgwhomeequip
  • 1902 Answers

SOURCE: how to remove rear seats from a kia optima 2006.5

There are two bolts located at the bottom part of the rear seats in the front just behind the driver seat and passenger seat, once those bolts are removed you will be able to lift up and out

Posted on Feb 09, 2009

  • 1986 Answers

SOURCE: can the rear and/or middle seats be removed from a

You should be able to... There should be a bar or a ******** the back of the seat that you can just pull...

Posted on Aug 13, 2009

ifranjan
  • 23 Answers

SOURCE: Kia rio rear seat belt got stuck ?

have to change seat belt

Posted on Oct 03, 2009

  • 35 Answers

SOURCE: I was removing the rear seat in a Kia Sedona.

hi squeeze the bars together and it will release the clips for you. if you need more information someone on this kia forum had the same problem and was given the steps to-do it.

http://www.kia-forums.com/kia-carnival-sedona-forum/38775-kia-sedona-2000-rear-seat-removal.html

Posted on Dec 29, 2009

  • 1 Answer

SOURCE: Kia Sedona seat stuck

Got it, with the help and eyes of my wife. The rear latch releases as the seat back is lowered. This release is ALMOST seat back down (about 3 inches above the seat bottom). As the seat back lowers, apply constant lift on the rear latch, and it will release as the seat back lowers. Hard-won knowledge - I think I invented some bad words in the process.

Posted on Feb 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kia soul rear window wont roll up 2012 kia soul


Try spaying the window tracks with lithium grease. The circuit breaker is tripping trying to move tight window

May 22, 2017 | Kia Cars & Trucks

1 Answer

How to remove the driver seat armrest?


on the end of the armrest should have a cap or a zipper and inside is the screw to un do the arm

Apr 27, 2014 | 2010 Kia Soul

1 Answer

How do I remove the rear bench seat on a Galant 2010 to install seat covers? Thanks


push back firmly at front of seat at bottomlocating clip released with upward preasure

Nov 14, 2012 | 2010 Mitsubishi Galant

1 Answer

I need to change my6 battery


Hi Robert.

In Buick models built before 2002 the battery is located under the hood, in the lower left hand corner of the engine compartment. To replace the battery remove covers, detach the positive cable and put it out of the way. Do the same with the negative cable (make sure you secure cables away from battery terminals).Undo the screws securing the holding rod and release the rod enough to remove the battery. Remove holder and free the battery.Perform operations in reverse order to install the new battery. Always connect the ground cable to new battery before connecting the positive cables.

NOTE: You asked the question listing a 1993 vehicle. Newer models have the battery located under the rear passenger's seat bench. It is necessary to remove the seat's cushion to access the battery. I

Regards.

Ginko

Aug 31, 2011 | 1993 Buick Regal

1 Answer

How to remove rear seat in 1996 dodge ram 1500


REMOVAL & INSTALLATION
  1. Clamp the seat belts to keep them from retracting.
  2. Locate and disconnect seat wiring at the connector(s).
  3. Move front seats forward or back for access to the hold down hardware.
  4. Put the rear seats in the stowed position.
  5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
  6. Remove the hardware securing the seat.
  7. On split bench models, lift the center seat upward to clear attachment stud
  8. Remove the seat from the vehicle.
NOTE Do NOT activate the track adjusters once the fastening hardware is removed.
  1. Installation is the reverse of removal.

336abe0.gif


Fig. Disconnect the wiring from under the seat

36c62e2.gif


Fig. Seat track mounting hardware locations-typical


d95c538.gif

Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram


1589e1e.gif

Fig. Split bench seat assembly-Ram


616f086.gif

Fig. Bucket seat mounting components-Durango shown


851105e.gif

Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

Aug 31, 2009 | 1996 Dodge Ram 1500 Club Cab

2 Answers

Locked my keys in trunk of 2002 kia rio , how do I take out the back seat??


Two large bolts secure the bench in place. Remove them. Three large bolts sechur the backrest in place. Remove them. Lift the backrest up until it unhooks from the three supports near the top. You will the be able to remove the plastic panels leading to the trunk. They are secured with small plastic retainers. Good luck. Takes about 15 minutes.

May 14, 2009 | 2002 Kia Rio

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

2 Answers

Want to replace fuel pump need help to where its at and how to do


Fuel pump is located inside the fuel tank access cover location. Here's the details:

  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Open the rear access door.
  4. Release the catch for the back seat and tilt the seat out of the way.
  5. Move the carpet behind the seat that covers the fuel pump access panel.
  6. Disconnect the fuel pump electrical connectors.
  7. Remove the screw securing the ground wire.
  8. Remove the four screws securing the fuel pump access panel and position it out of the way.
  9. Remove the hose clamps connecting the fuel hoses to the fuel pump.
  10. Disconnect the fuel hoses from the fuel pump.
  11. Disconnect the fuel tank pressure sensor electrical connector.
  12. Remove the eight retaining screws securing the sender assembly to the tank.
    WARNING The fuel assembly is easily damaged. Use care when removing the assembly from the tank.
  13. While twisting and tilting, gradually lift the fuel sender assembly and remove from the tank.
  14. Wrap the fuel pump assembly in a rag before removing the assembly from the vehicle.
  15. Cover or seal the fuel tank until installing the fuel pump assembly.
  16. Remove the retaining hardware that holds the sender to the fuel pump assembly.

To install:
  1. Install the retaining hardware that holds the sender to the fuel pump assembly.
  2. Remove the temporary covering or seal that was used to protect the tank.
  3. Install the fuel pump into the access port on top of the fuel tank.
  4. Carefully, twist the fuel pump as necessary to properly position it in the fuel tank.
  5. Install the eight retaining screws securing the sender assembly to the tank.
  6. Connect the two fuel hoses to the pump and secure with clamps.
  7. Connect the fuel tank pressure sensor electrical connector.
  8. Insert the ground wire and fuel pump electrical connector through the access hole and install the access cover.
  9. Connect the fuel pump electrical connector.
  10. Secure any loose wiring with adhesive tape and reattach the carpeting.
  11. Release the catch for the rear seat and put the rear seat in the normal position.
  12. Close the rear access door.
  13. Reconnect the negative battery cable.
I can help you further and show you where you can access the information for free. Good luck!

Apr 28, 2009 | 2000 Kia Sportage

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge...


the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.
  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in the upright position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Mar 02, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
2012 Kia Soul Base Wagon 1.6L 4-cyl. 6-speed Manual Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...