Question about Cars & Trucks

Open Question

Fog light install ford territory

How do i wire fog lights into a ford territory

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 88 Answers

SOURCE: need wiring shematic for fog lights 2005 toyota corolla

im pretty sure these cars were already prewired for fog lights .there should be some plugs behind the bumper to fit them.if not get back i will explain how to wire them up.best of luck.

Posted on Oct 17, 2008

chuck943
  • 783 Answers

SOURCE: 1st time install of OEM fog lights into a 1999 Mercury Cougar?

Look under the dash near where the headlamp switch mounts and if yours is equipped you should see I think it is a blue 4 pin connector with the following wire colors OG,OG/WH,OG/GN,BK.
This is for the fog lamp relay.If yours has this connector then you will need to purchase a relay ford part number F6RZ-14N089-AA should list for about $10.

Posted on Feb 25, 2009

ButtFuzz
  • 463 Answers

SOURCE: i need a wiring diagram for fog lights oem to my toyota

The link below is a Typical fog lamp / driving lamp hookup. Keep in mind that in most states, for these lamps to be 'legal' (and thus pass inspection), you must wire them such that:

1. You can cut them off (in other words, there must be a switch installed to turn them off)

and

2. They may only be operated with the low beams. (therefore, you must power your on/off switch from the low beam circuit)

http://www.accessconnect.com/fog_driving_lights_wiring.htm

Posted on Feb 28, 2009

  • 582 Answers

SOURCE: ford focus c max towbar electrics

ARE YOU READY
L.H. STOP AND TURN ( YELLOW )
R.H. STOP AND TURN ( GREEN )
TAIL, LICENSE, SIDE MARKERS ( BROWN )
GROUND ( WHITE )
NOW THE COLORS ON THE VEHICAL ARE GOING TO BE DIFFERENT AND YOU WILL NEED A 12 VOLT TEST LIGHT FOR MAKEING SURE YOU HAVE THE WRITE WIRES FROM THE CAR TO THE TOE BAR, DON'T NEED BACK UP TIGHTS FOR THIS

Posted on Aug 25, 2009

  • 1 Answer

SOURCE: how to install OEM 2007 camry fog light?

Follow the link below to find with picture and step by step instruction to mount the foglights. It's lot easy than connecting the wires.
http://meandmycamry.freeservers.com/photo.html

For me I managed to install the foglights but not sure how to connect to the power and bring the wire to the dashboard. My car didn't come with wiring connections for foglights. Would appreciate if someone can help me with that ( possibly instructions with pictures), Thanks.

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace fog light globe on 2006 ford territory


To get at the fog lights out you have to unclip them, 4 latches - one on each cnr of the black ousing which can be reached by reaching down past headlights.
Once loose they can be accessed by removing the wheel arch lining and pull out that way after unclipping the wiring block connnector. They look like a sealed unit but are not and come apart between the ehite and black housing. This makes it possible to be able to replace the 55w halogen bulb

Oct 23, 2013 | 2006 Ford Territory 4.0

1 Answer

How to install original factory fog lightson ford escpae xls 2010 I purchase the original fog lights butcanot find the harness or connectors. Do I need to purchase another harness?


hi when you purchased these they should have come with a wiring kit supplied, if not then you will have to go to ford and ask them for the wiring kit for them, on most replacement fog lights not ford made come complete with wiring included...hope this helps

Aug 01, 2010 | 2008 Ford Escape

1 Answer

How do u change a bulb in the fog lights on a


The fog lights on most vehicles sit directly underneath the headlight bulbs. The ballast and wiring work just like the headlights, so changing them takes not much time. The procedure to change the fog light is as follows:-- 1) Open the hood and reach down underneath the headlights to unplug the electrical plug from the fog light assembly. Squeeze the top of the release tab and pull the connection off the bulb's ballast. 2)Turn the fog light counterclockwise to remove it from the fog light housing. 3)Install the new fog light bulb.Then connect electrical plugs properly. 4) Test the fog lights by turning it ON. Thanks. you can rate this solution and show your appreciation.

May 20, 2010 | 2003 Ford Focus

1 Answer

I'm having trouble accessing the fog lights on my Ford Territory (2004) I cannot access the bulb? any drawings / ideas


replace the whole assy.. its maintenance free and needs to be replaced entirely when busted

Jul 19, 2009 | 2004 Ford Taurus

1 Answer

Wiring of fog lights on 95 Mustang


If you bought the fog lights from Ford and they plugged into factory plugs at the front bumper, then I suspect you need the headlight switch that came optional for your car. You will need to install a relay into the fuse box. Check for any fuses for that circuit. I did one on a Ford f-150 and the switch came with the lights from Ford.Usually the fog lights are not on until you push a button or turn the switch.

Mar 15, 2009 | 1995 Ford Mustang

1 Answer

Unused wires for fog lights


could be the + or -for the lights

Mar 15, 2009 | 2002 Ford F250 Super Duty SuperCab

1 Answer

1st time install of OEM fog lights into a 1999 Mercury Cougar?


Look under the dash near where the headlamp switch mounts and if yours is equipped you should see I think it is a blue 4 pin connector with the following wire colors OG,OG/WH,OG/GN,BK.
This is for the fog lamp relay.If yours has this connector then you will need to purchase a relay ford part number F6RZ-14N089-AA should list for about $10.

Feb 25, 2009 | 2000 Mercury Cougar

1 Answer

Installing new fog/driving lights on an 03 mustang. there are wires attached to the fake switch on the dash. Is there a plug somewhere that I just plug into the fog light bulb?


the fog light is normally one complete assembly that you just unplug from the outside and replace with a new one auto zone is a good place to help with this

Jan 11, 2009 | 2003 Ford Mustang

1 Answer

Lights


FROM: Lusty Kid:

Your fog lights should not work with high beam... they should work with the low beams. they are connected wrong, which probably drew too much current through the light switch burning out the contact points for the parking lights in the switch

Start by Fixing the fog light connections to work with low beams. Appears to me this was not factory installed. Aftermarket kit maybe! Then see if your parking lights work. If parking lights don't work still and everything else works, replace the light switch $50 at the dealer. The switch works the fog lamps when you pull out the knob to turn on the fog lamps when the lights are turned on. When the fogs are on you will see a little amber light to let you know your fogs are on. When you switch to high beam the fog lamps go off. Again if its not working that way, then is wired wrong. Needless to say, there should be connectors in the harness of the lights for the fog lamps. Use those if possible with the kit that you can get at the dealer, or you can splice the connector with those blue splicing clips sold at the auto part store. Make sure ground is ground when splicing and water proof the connection sith silicone and tape.

Dec 13, 2008 | 2004 Ford F150

1 Answer

Front fog lights!


The fog light switch is located to the right of the rear wiper switch. Also the fog lights will not operate when the high beams are on. If the rear fog is the defrost switch,you are in the right area.If the switch is not there,they could have been dealer installed and are wired to come on when the low beams are on. Hope this helps,Good luck

Aug 26, 2008 | 1996 Ford Probe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...