Question about 2006 Hyundai Tucson

Open Question

Accelerator pedal sensor - 2006 Hyundai Tucson

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dtc p0121 throttle position (tp) sensor performance


code p 0121 has to answers
1--refers to throttle position (TP) sensor/accelerator pedal position sensor A--range /performance problem====causes --accelerator cable adjustment--TP/APP sensor ---wiring
The second reference is the same and the causes are--accelerator cable adjustment--TP/APP switch
(APP is accelerator pedal position)

Aug 30, 2016 | Cars & Trucks

1 Answer

I changed everything on a 2007 Chevy uplander the camshaft position sensor And the purged sensor And the throttle body and still the check engine light and the reduce engine power came back on


Reduced Engine Power Mode When the ECM detects a condition with the TAC system, the ECM may enter a reduced engine power mode. Reduced engine power may cause one or more of the following conditions:
?€¢
Acceleration limiting--The ECM will continue to use the accelerator pedal for throttle control, however, the vehicle acceleration is limited.


?€¢
Limited throttle mode--The ECM will continue to use the accelerator pedal for throttle control, however, the maximum throttle opening is limited.


?€¢
Throttle default mode--The ECM will turn OFF the throttle actuator motor and the throttle will return to the spring loaded default position.


?€¢
Forced idle mode--The ECM will perform the following actions:


-
Limit engine speed to idle by positioning the throttle position, or by controlling the fuel and spark if the throttle is turned OFF


-
Ignore the accelerator pedal input


?€¢
Engine shutdown mode--The ECM will disable fuel and de-energize the throttle actuator.
Did you have it checked for DTC's - diagnostic trouble code's related to the reduced engine power ?
All so has APP sensor gas pedal !
Accelerator Pedal Position (APP) Sensor
The accelerator pedal contains 2 individual accelerator pedal position (APP) sensors within the assembly. The APP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
?€¢
A 5-volt reference circuit


?€¢
A low reference circuit


?€¢
A signal circuit

The APP sensors are used to determine the pedal angle. The engine control module (ECM) provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors provide the ECM with signal voltage proportional to the pedal movement. The APP sensor 1 signal voltage at rest position is less than 1 volt and increases to more than 4 volts as the pedal is actuated. The APP sensor 2 signal voltage at rest position is less than 0.6 volt and increases to more than 2 volts as the pedal is actuated.
Your best bet is take your vehicle to the dealer !
al

May 03, 2016 | Cars & Trucks

1 Answer

How do I replace the accelerator pedal position sensor?


You need to replace the accelerator pedal assembly ! That's the whole gas pedal assembly , two bolts hold it fast to the fire wall . Search from over 10 Million Auto Parts P2138 APPS Accelerator Pedal Position Sensor Fix 3 5L Chevrolet Impala

Feb 27, 2015 | 2006 Chevrolet Impala

1 Answer

Accelerator pedal


Hello,

You can try to reset / recalibrate the accelerator pedal sensor at a bmw indy shop.
If this does not help the accelerator pedal sensor may need cleaning or replacement.

Hope it helps

Jul 23, 2014 | 2007 BMW 120i Sport

1 Answer

Check engine light sensor


DTC P2138: Accelerator Pedal Position (APP) Sensor A/B (Throttle Position Sensor D/E) Incorrect Voltage Correlation.

Accelerator pedal position (APP) sensor A and accelerator pedal position (APP) sensor B are potentiometers, and they are installed in the engine compartment.

The APP sensors A and B are operated via the throttle cable to determine the accelerator opening value when the driver presses the accelerator pedal. The accelerator pedal opening value is converted to a signal in APP sensors A and B and transmitted to the engine control module (ECM)/powertrain control module (PCM) to compute the target position. The target position signal is then transmitted to the throttle actuator control module.

APP sensor A is for the primary control, and APP sensor B is a back-up of APP sensor A in case it malfunctions. Both sensors compare their output voltage to each other for malfunction detection.

When the voltage difference of APP sensor B is out of a fixed range for a set period of time, the ECM/PCM detects a malfunction, and a DTC is stored.

Sep 15, 2013 | 2007 Honda Accord Sedan

2 Answers

Reduced engine power, service traction control, service stabilitrak


First of all a scan tool is need for this not a code reader, you need to view scan data after you find what code is stored in the PCM. It could have a problem with the powertrain control module, wiring, or the Accelerator Pedal Position (APP) Sensors. Here are a few codes that could set .
DTC P2120: Accelerator Pedal Position (APP) Sensor 1 Circuit

DTC P2122: Accelerator Pedal Position (APP) Sensor 1 Circuit Low Voltage

DTC P2123: Accelerator Pedal Position (APP) Sensor 1 Circuit High Voltage

DTC P2125: Accelerator Pedal Position (APP) Sensor 2 Circuit

DTC P2127: Accelerator Pedal Position (APP) Sensor 2 Circuit Low Voltage

DTC P2128: Accelerator Pedal Position (APP) Sensor 2 Circuit High Voltage

DTC P2138: Accelerator Pedal Position (APP) Sensor 1-2 Correlation

Oct 02, 2012 | 2008 Chevrolet Tahoe LS

3 Answers

Error code p2138


Here is the definition. You may need to have someone check the accelerator pedal position sensor and the circuit.

P2138 NISSAN Description The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the Engine Control Module (ECM).
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
Read more: http://engine-codes.com/p2138_nissan.html#ixzz26J3D2x8s

Sep 12, 2012 | 2010 Nissan Versa 1.8

2 Answers

09 impala accelerator pedal sensor?


the pedal sensor is part of the gas peda assembly. The whole thing needs to be replaced if there is a problem with the sensor.

Feb 16, 2012 | 2009 Chevrolet Impala LT

1 Answer

Error code p1271 on trailblazer


That trouble code is faulting the accelerator pedal sensor. The APP sensors are located in a TAC module mounted to the accelerator pedal bracket. There are three individual APP sensors within the TAC module. Three separate signal circuits, low reference circuits, and 5v reference circuits are used to determine the accelerator pedal position. The APP sensor signal voltages increase when the accelerator pedal is depressed.

Nov 26, 2011 | 2003 Chevrolet TrailBlazer

2 Answers

Sometime no accelerator response


YOUR ACCELERATOR PEDAL SENSOR ON ACCELERATOR PEDAL IT HAS BOLTS HOLDING IT IN PLACE.JUST UNPLUG ACCELERATOR CONNECTOR AND REMOVE THE BOLTS THEN SENSOR.

Jun 06, 2010 | 2002 Ford F350 Super Duty DRW Reg. Cab

Not finding what you are looking for?
2006 Hyundai Tucson Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...