Question about Cars & Trucks

Open Question

MEANING OF BENDIX TRAILER ABS BLINK CODE 6-6-6

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i connect running light wire all blink w/ turn sig. and when i connect trailer to bike (trailer hitch) i blow a fuse?


shorted trailer harness, all blink because there is no ground in wiring system. correct the wiring issues for a complete repair

Mar 05, 2016 | Cars & Trucks

1 Answer

Fault code 00 01 Ad


Fundamentals of Medium/Heavy Duty Commercial Vehicle Systems

https://books.google.com/books?isbn=1284041166
CDX Automotive,, ‎CDX - 2015 - ‎Transportation
If no fault codes are active, the warning lamps remain lit. ... (ABS) 128 - Engine 130 - Transmission 136 - Brakes (ABS) 137 - Trailer (ABS) FMI 00 01 02 03 04 ...

Nov 25, 2015 | Cars & Trucks

1 Answer

2003 jaguar s type code p1000 and c1165


the p1000 is a system readiness code meaning the car is checking itself..it means its not finished etc but once it has the code will change to p1111..meaning system check completed, the c1165 is a abs or wheel speed code, check the wheel where this code is originating

Apr 03, 2014 | 2003 Jaguar S-Type

1 Answer

When I have a trailer hooked up and turn my left signal on both taillights blink on trailer-NOT THE TRUCK. then if I turn on the right signal it works normal. I checked the wiring for current ahead of the...


diagnostic times 3
test truck on its own (never mind the trailer plug) if ok not truck
test trailer on its own (use good batery or charger) if ok not trailer
test truck trailer system now look for cross wire or pinch wire in trailer harness
could also be corosion at rear 6-or-7 way plug causing crssover power
eliminate source one at a time and you will locate problem

Apr 02, 2011 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

1996 NEON ... YESTERDAY ON THE WAY HOME IT DIED 6 TIMES ... RUNS OK ... GET BACK ON THE ROAD ... GO A MILE OR SO .. DIES AGAIN ANY THOUGHTS ?


There's multiple possibilities. Some of them are a partially clogged fuel filter, poor fuel pressure, a bad sensor or sensors, etc...
Have you checked/changed the filter? What's the fuel pressure?
You can access a simplified version of the trouble codes on this model - with the car off, turn the ignition switch on, off, on, off, and on again relatively quickly. The check engine light will blink out the codes. An example would be blink, pause, blink, blink. This would be code 12. Chilton's or Haynes books give you the code's meaning (that code means battery disconnect). These can at least give you a place to start.

Aug 04, 2010 | 1996 Dodge Neon

1 Answer

I need a diagram of the underhood fuse block for my 2002 ford explorer. I don't have an owners manual.


Fuse/Relay Location*Fuse Amp Rating* Description
1 60A** PJB 2 30A** BSM 3 20A** Not used (Spare)
4 30A** Rear defrost 5 40A** ABS (pump)
6 60A** Delayed accessory circuit breaker
7 20A** Power point #2 8 — Not used 9 20A** Power point #1
10 30A** ABS module (valves) 11 40A** PTEC
12 50A** Ignition relay/Starter relay
13 40A** Trailer tow battery, Trailer tow turn signals
14 10A* Foglamps 15 15A* Memory (KAPWR)
16 15A* Headlamp switch 17 20A* 4x4 (v-batt 2)
18 20A* 4x4 (v-batt 1) 19 20A** High beam relay
20 30A** Electric brake 21 30A** Front wiper motor
22 20A** Autolamp; Low beam 23 30A** Ignition switch
24 20A* Rear Fog Lamps 25 – Not used
26 15A* Fuel pump 27 20A* Trailer tow lamps
28 20A* Horn relay 29 60A** PJB 30 20A** Rear wiper motor
31 — Not used 32 — Not used 33 30A** Auxiliary blower motor 34 30A** Power seats, Adjustable pedals
35 20A** Rear power point 36 40A** Blower motor
37 15A* A/C clutch relay/Transmission
be7a74c.jpg

Nov 15, 2009 | 2002 Ford Explorer

2 Answers

Looking For the ECU on a 2002 2500hd


the ecu on a 2500 is under the hood on the drivers side. if it is a diesel. still in the same place for gas too.

Dec 10, 2008 | 2002 GMC Sierra 2500HD

1 Answer

ABS Light gives out three codes,Where can I get a list of codes to trouble shoot by?


Hi,

Most Honda ABS warning light will blink in 2 parts, main system and then sub system to form the code pair. As an example is 3 blinks then 3 blinks is a code 3-5. Once determined, reference below listing.
1 - ABS pump motor over-run
1 2 ABS pump motor
1 3 high pressure leakage
1 4 pressure switch
1 8 high pressure system
2 1 parking brake
3 1 pulser RF
3 2 pulser LF
3 4 pulser RR
3 8 pulser LR
3 12 different diameter tires
4 1 wheel sensor RF
4 2 wheel sensor LF
4 4 wheel sensor RR
4 8 wheel sensor LR
5 - rear wheel lock - R/L
5 4 rear wheel lock - R
5 8 rear wheel lock - L
6 - fail-safe relay - F/R
6 1 fail-safe relay - F
6 4 fail-safe relay - R
7 1 solenoid - RF
7 2 solenoid - LF
7 4 solenoid - R
8 1 ABS function
8 2 CPU comparison
8 4 IC self-check

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 25, 2008 | Honda Accord Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...