Question about 2000 Mitsubishi Eclipse

Open Question

2000 eclipse cam sensor location V6

2000 ECLIPSE GT V6 CAMSHAFT SENSOR LOCATION

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

danr990
  • 1 Answer

SOURCE: 2002-2004 Mitsubishi Eclipse Camshaft Position Sensor Location?

would this sensor make the car not start when it is hot?

Posted on Jun 05, 2012

lacrow146900
  • 38 Answers

SOURCE: Where is the camshaft sensor located in a 2001 Mitsubishi eclipse spyder gt V6 3.0 manual

The ignition coil and cam sensor are built into the distributor.

Posted on Dec 03, 2012

  • 2 Answers

SOURCE: Oil Pressure Sensor

how to set Torque setting for main and connecting rod qd32 engine

Posted on Jul 23, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 eclipse 2.4 auto rs. Car just shut off while driving. Scanned the mil and showed a code for the camshaft position sensor. Car owners father replaced the crankshaft position sensor (dunno...


if the code shows a cam position sensor then it is the cam position sensor and not the crank position sensor
get the car to an accredited service center before it cost more money from inexperienced interference

May 28, 2017 | 2000 Mitsubishi Eclipse

1 Answer

Where isa the crank shaft position sensor located on a 2000 V6 Eclipse?


0996b43f8020334f.jpgAuston, I couldn't load both at the same time go to auto zone sign is (it free) and look it up

Sep 10, 2014 | 2000 Mitsubishi Eclipse

1 Answer

Oil Pressure Sensor


how to set Torque setting for main and connecting rod qd32 engine

Jul 22, 2013 | Mitsubishi Cars & Trucks

1 Answer

2000 Mitsubishi eclipse gt


see the diagram attached. God bless you
3163d4ca-779e-46fc-8616-1eb120b57e7d.jpg

Jul 22, 2013 | Mitsubishi Cars & Trucks

1 Answer

Location for camshaft position sensor on 2.4 2005 eclipse


Remove air flow duct away from engine enough to look under it.. Cam sensor is located there.. Held on by one 10 mm bolt and clip. should be red wire, green with yellow stripe and a black one if my memory serves me right.. I have same car different year same engine.. I hope this helps you. please rate my answer thank you

Feb 21, 2013 | 2005 Mitsubishi Eclipse

1 Answer

Change a crankshaft position sensor on a 2000 eclipse


Is this a V6 or 4cyl???>>>(V6) This requires removing the Harmonic balancer (crankshaft pulley). Remove (R) front wheel, remove engine splash Guard, Remove crank pulley, remove lower timing belt cover. The Crank sensor is located behind the crank shaft pulley!! I highly recommend having this done by a certified tech, requires special tools. Hopefully this helps!!

Mar 11, 2010 | 2000 Mitsubishi Eclipse

1 Answer

2000 ford tauras,auto,84k miles, small v6, missing between 45 & 55 mph. Under & over no missing noticed. spark plugs changed @ 70k. Original wire and sensors; as shop said very good. Suggestions...


Sounds like it could be a cam position sensor.



2000 Ford Taurus V6-3.0L DOHC VIN S
Camshaft Position Sensor: Service and Repair
REMOVAL
1. Disconnect the battery ground cable. For additional information, refer to Battery.
2. Remove the Camshaft Position (CMP) sensor.
1 Remove the electrical connector.
2 Remove the bolt and the CMP sensor.
INSTALLATION
1. To install, reverse it removal procedure
1. To install, reverse the removal procedure.

Sep 06, 2009 | 2000 Ford Taurus

1 Answer

Ineed to know the location of the cam sensor on a ford escape 2002 with the 3.0 liter V6 DOHC


SECTION 303-14: Electronic Engine Controls 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor —3.0L (4V) Removal and Installation
  1. Remove the camshaft position (CMP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Remove the sensor.
4544c22.gif
#56 is the cam sensor. please rate as fixed if this is what you need.

231ee68.gif

May 02, 2009 | Ford Escape Cars & Trucks

1 Answer

I HAVE A 2000 DODGE STRATUS 2.5 V6. WHERE IS THE CAMSHAFT SENSOR AND CRANKSHAFT SENSOR LOCATED


Cam is on the end of the block, crankshaft sensor is on the bottom of the block. Both are easy to change....are you changing these due to poor performance or no start condition?

Mar 21, 2009 | 2000 Dodge Stratus

Not finding what you are looking for?
2000 Mitsubishi Eclipse Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...