Question about Nissan Frontier

Open Question

How to remove starter on a 2000 nissan frontier xe v6 4x4

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mnabi01
  • 94 Answers

SOURCE: 1998 Nissan frontier: where is the ignition coil?

the coil is inside the distributor under the cap.

Posted on Jan 29, 2009

Ad
dealt_soul
  • 296 Answers

SOURCE: 2000 NISSAN FRONTIER VIBRATION

Check tire balance, rear wheel bearings and i would replace u joints front and back, anyway if they have never been repaced.

Posted on Feb 15, 2009

  • 1 Answer

SOURCE: 2004 nissan frontier crew cab radio

the plastic around the gear shifter will pop up with a good pull, then turn it side ways to get over the shifter, then there are 2 screws the hold the bezel down around the radio and air vents, then just pull from the air vents it will pop off to reveil the screws to the radio

Posted on Feb 27, 2009

  • 2 Answers

SOURCE: change brake light bulb on a 2000 Nissan Frontier

The entire bed line will need to be removed. The long screws that hold the metal bracet where the bed extender attaches also hold the tail light assembly in place.
I pulled the bed liner up at a 45 degree angle and layed it on top of the cab. This revealed the screws. Take both screws out and lay to the side along with the metal bracket for the bed extender.
Now firmly grab the edges of the tail light assembly and pull...there are 2 hard rubber nipples that snap in to hold the assembly. You will feel like you might break it but you won't..just pull straight back hard. The assembly will "POP" out and then you can just twist the back of each bulb there are (3) and pull out..now you will see the bulbs..just pull the bad bulb straight out and push the new one into place. Now just reassemble. Total time will be 30-45 min. for this repair.

Posted on May 04, 2010

  • 14585 Answers

SOURCE: 2000 nissan frontier knock sensor code & distributor

no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Posted on Jun 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove a starter on a 4 wheel drive 2002 Nissan frontier???


How to replace a starter on a 2000 nissan frontier v6 3.3L ...

? 3:14
www.youtube.com/watch?v=ibyIqgGeIug
Jan 6, 2013 - Uploaded by Raul Romo I show how To replace a starter on a 2000 Nissan frontier Part 1. ... and solenoid plug from under the rubber splash guard in thewheel well.

Oct 07, 2015 | 2002 Nissan Frontier Crew Cab

1 Answer

How replace the starter in 2001 nissan frontier manual trassmisson


same as all cars. (mostly)
this your first starter?
no problem.
its in the FSM read that.
or alldata.com , log in
or pull neg lug on battery
gain access to starter, (RTM)
remove wires there.
remove 2 bolts
its out.
reverse is same , read above backwards.

Jul 17, 2014 | 2000 Nissan Frontier

1 Answer

2000 nissan frontier xe. starter went out, replaced started. worked for a couple days and went out again, starter had factory defect, put new starter in and still wont turn over,just clicks a lot. all


When you get your Frontier started after jump starting it, does it stay running? If it does, you probably just have a bad battery. If you have a battery and brake icon come on, on your dash, you probably have a bad alternator. you could go to auto zone and they will be able to test your battery.

Mar 06, 2014 | Nissan Frontier Cars & Trucks

1 Answer

No headights or turn signals on Nissan Frontier XE 2007


Sounds like multi-function/ turn signal switch

Mar 09, 2013 | 2000 Nissan Frontier

1 Answer

2000 nissan forntier dash lites


Probably a bad ground, take it to a speedometer shop, if you can't find the loose ground and they'll fix it inexpensively.

Dec 09, 2012 | 2000 Nissan Frontier

1 Answer

Removing factory radio from 2000 Nissan Frontier XE


There are two screw at the bottom of the black plastic trim panel around the radio. Remove the screws and pull the trim panel back. Remove the four screws around the radio, unplug the wires on the back of the radio and you are finished!

Aug 15, 2009 | 2000 Nissan Frontier

1 Answer

2000 NISSAN FRONTIER VIBRATION


Check tire balance, rear wheel bearings and i would replace u joints front and back, anyway if they have never been repaced.

Jan 12, 2009 | 2001 Nissan Frontier Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...