Question about 2007 Toyota Auris 2.0

Open Question

Reset malfunction indicator lamp - 2007 Toyota Auris 2.0

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

StormStrikes
  • 104 Answers

SOURCE: Malfunction indicator lamp

The Malfunction Indicator Lamp or MIL (Also called the check engine light or service engine soon light) comes on when the on board computer detects an issue with the operation of the engine or transmission.

The best thing to do is to take the vehicle to an auto parts store like Autozone and have them hook up their scan tool to the vehicle and read the code. They can read it, tell you what it is and also tell you what the code means.

If it is pointing to a faulty component or sensor and you replace or repair the component the the light will go off on its own after the computer sees that the malfunction is no longer present.

You can have the code cleared, but if whatever caused the light to come on in the first place is not addressed then it will just come back on eventually.

Posted on Dec 31, 2008

beduncan
  • 73 Answers

SOURCE: Malfunction Indicator Lamp

Take your car to your local autoparts store and have them pull the codes - this is free at most stores. Post the codes when you're done. This can be caused by anything - even as simple as not tightening your gas cap (you should hear the clicks - it doesn't damage the cap).

Posted on Aug 07, 2009

emissionwiz
  • 75235 Answers

SOURCE: malfunction indicator lamp in my toyota corolla is on how i fix?

The check engine light also called the malfunction indicator comes only when the computer control unit (called the PCM) senses a fault in the electronic controls of the engine and/or the emission system, there are about 200 possible faults that turn the light on, to know what has developed a problem you must have the system tested, this is called an OBD2 fault code test, Kragen and Autozone parts stores do this testing for free.

Posted on May 27, 2010

bogdanodwazn
  • 5629 Answers

SOURCE: How to fix Toyota Landcruiser "Malfunction Indicator Lamp Light"

need a scanner to find the code and to fix the problem.

Posted on Feb 24, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuses ok,light in dash tested and works. But check engine light does not come on when you turn on the ignition. What else should I check? This is a ford ranger XLT 4x4 4.0L V6-245cid engine (pushrod)


The instrument cluster (10849) carries out a display proveout to verify that all warning/indicator lamps and monitored systems are functioning correctly. When the ignition switch (11572) is in the ON position with the engine (6007) off, the following indicators will illuminate:
  • CHECK ENGINE/malfunction indicator lamp (MIL).
  • CHECK GAGE warning indicator.
  • Charge system warning indicator.
  • Anti-lock brake warning indicator (ABS).
  • Safety belt warning indicator (60second proveout).
  • Air bag indicator.
  • An indicator is inoperative - CHECK ENGINE/malfunction indicator lamp (MIL)
  • Bulb.
  • Circuitry.
  • Instrument cluster printed circuit.
  • Powertrain control module (PCM) (12A650).
  • GO to Pinpoint Test N .

Feb 15, 2016 | Cars & Trucks

1 Answer

What is malfunction indicator lamp on 03 mercury sable


Malfunction indicator ,check engine lamp . service vehicle soon etc.. Trouble Codes Check Engine Light On

Oct 23, 2015 | Mercury Cars & Trucks

1 Answer

Push button for four wheel drive isn't working


Do you have any lights on the dash lit ?
SERVICE indicator (4WD/AWD) Lamp
The SERVICE indicator (4WD/AWD) lamp is an integral part of the cluster and cannot be serviced separately. This lamp is used to inform the driver of the vehicle of malfunctions within the automatic transfer case (ATC) system. The SERVICE indicator (4WD/AWD) lamp is controlled by the transfer case shift control module via CKT 1567. this system will set DTC'S if there is a problem .
Diagnostic Trouble Codes DTC B2725 ATC Mode Switch Circuit Malfunction DTC C0300 Rear Speed Sensor Malfunction DTC C0305 Front Speed Sensor Malfunction DTC C0308 Motor A/B Circuit Low DTC C0309 Motor A/B Circuit High DTC C0310 Motor A/B Circuit Open DTC C0315 Motor Ground Circuit Open DTC C0323 T-Case Lock Circuit Low DTC C0324 T-Case Lock Circuit High DTC C0327 Encoder Circuit Malfunction DTC C0367 Front Axle Control Circuit High DTC C0374 General System Malfunction DTC C0376 Front/Rear Shaft Speed Mismatch DTC C0387 Unable to Perform Shift DTC C0550 ECU Malfunction DTC C0611 VIN Information Error you probably should take this to a repair shop !

This tt

Feb 22, 2015 | 1999 Chevrolet Silverado 1500

1 Answer

Malfucnction Indiator lamp


The malfunction indicator lamp(MIL) indicates a faulty sensor/s in the ECM system management. If it is flashing it will be a code as to the fault and the faults can be read by a scanner to determine the nature of the fault. Once the fault has been fixed then a scanner can be used to reset the MIL

May 31, 2014 | Pontiac G6 Cars & Trucks

1 Answer

Malfunction indicator lamp


Have the CPU program reset as removing the battery corrupts the program

Mar 17, 2014 | Chevrolet Cars & Trucks

1 Answer

P1613 what it means engine light on


  • Check Malfunction Indicator Lamp (MIL)
  • Check Wiring/Connectors from/to Malfunction Indicator Lamp (MIL)
  • Check Control Module Coding
  • Check/replace ignition/starter switch
  • Check relay on left plenum chamber for execive wear

Mar 15, 2014 | 1998 Volkswagen Passat

1 Answer

I went to scan my toyota yaris car and the following codes were give ; temperature ckt low input po117


EOBD II Error Code: P0117
Fault Location:
Engine Coolant Temperature (ECT) Sensor (G62) - Low Input
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
Coolant thermostat.
Wiring short to earth.
Engine coolant temperature (ECT) sensor.

EOBD II Error Code: P0340
Fault Location:
Camshaft Position (CMP) Sensor A (G40), Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Wiring from/to Camshaft Position Sensor (CMP) faulty.
Camshaft position (CMP) sensor faulty.
Timing misaligned.
Possible Solutions:
Check Wiring from/to Camshaft Position Sensor.
Check Camshaft Position Sensor.
Check Timing.

EOBD II Error Code: P0500
Fault Location:
Vehicle Speed Sensor (VSS) - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Non Emission Fault - No warning light.
Wiring.
Vehicle speed sensor (VSS).
Engine control module (ECM).

Dec 13, 2012 | 2001 Toyota Yaris

1 Answer

MY honda 2003 crv the malfunction indcaitor lamp has turn on,what should ido thanks.


take it to an auto parts store and allow them to put it on a computer they can tell you what cause it to light and reset it for you aswell

Aug 13, 2012 | Honda CR-V Cars & Trucks

1 Answer

How do you reset a service engine light on 2001 saturn l100?


You will need a OBD II scanner to reset or turn off the MIL (Malfunction Indicator Lamp).

Jun 17, 2010 | 2001 Saturn L-Series

Not finding what you are looking for?
2007 Toyota Auris 2.0 Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...