Question about 2002 Nissan Frontier Crew Cab

Open Question

Torque spec for water pump,2002 Nissan frontier

I need too know what to tighten the water pump bolts on my 2002 Nissan frontier

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

Ad
rick_amick
  • 72 Answers

SOURCE: Changing V belts on Nissan Frontier 2002 4cyl

That should be right if it is an idler pulley. On belts that do not have idler pulley you will have to loosen lock bolt on adjuster. Like alternator

Posted on Mar 24, 2009

  • 383 Answers

SOURCE: lifter knocking on 1999 Nissan Frontier

red: there were two engines used in the1999 frontier.
The VG30 (V-6 )and the KA24DE (4- CYL)
If you have a V-6, there is no adjustment you can make on the valve clearances. They are hydraulic and self adjust. If they are noisy, you might try changing the oil and filter and using an oil additive designed for addressing high mileage motors with noisy lifters. Marvel Mystery oil actually works, but follow the instructions. MORE IS NOT BETTER!
The 4 Cly engine does not have adjustable valve clearances from the stand point of using a few wrenches, one to adjust and the other to lock the adjuster when the clearance is correct.
These valve clearances are set using shims which are "metal discs about the size of a quarter. They come in various thicknesses and based on the measurement between the base of the cam when the highest point of the lobe is facing the 12:00 position, you place a feeler gauge between the base of the cam and the top of the shim.
If it is too loose or too tight, you use your feeler gauges to find out what it would take to make a zero clearance situation. From there, you remove the shim, measure it. Based on your findings during your initial measurements, you can calculate whether you need to use a thicker or thinner shim.
So to answer your question: unless you have a lifter confused with some other component, there is no means of torquing a lifter down on either series engine which came in that truck.
Please let me know if I can help you further. There must be some reason why you have asked this question......?

Posted on Apr 16, 2009

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

  • 36 Answers

SOURCE: I need head bolt torque sequence for 2002 nissan

So 80 degrees is approx. how many ft lbs.

Posted on Jun 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for the heads on a 2000 Nissan Xterra 3.3 l


AutoZone has a lot of info on torque specs for various vehicles.
The Xterra uses torque to yield bolts which must be replaced every time the bolt is removed.
Here's the site -
https://www.autozone.com/repairguides/Nissan-Frontier-Xterra-1998-05/Engine-Mechanical-Components/Cylinder-Head/_/P-0996b43f8037f9d4

Jan 09, 2018 | Nissan Cars & Trucks

2 Answers

On Nssan Frontier 1999 2.4L I am replacing the waterpump and fan clutch. I need to know the torque measurements for the pump- and clutch nuts.


Go to autozone.com and they have free online books you can look it up just enter make model and engine type

hope this helps mike

Jul 20, 2016 | 1999 Nissan Frontier

1 Answer

2004 nissan frontier head torque specs


You should have torque to yield bolts there. That means single use - you need to buy new bolts. Then, you would torque to spec (maybe 10-12 ft. lbs.) then an additional 65 degrees of tightening rotation.
Call your local auto parts supplier.
Repair Guides Specifications Torque Specifications AutoZone com

Feb 26, 2015 | Nissan Frontier Cars & Trucks

1 Answer

I need to know the correct torque specs for the 4 bolts that hold the a/c compressor on my 2003 Suzuki Aerio. In order to replace the water pump it was necessary to remove the compressor. The book supplied...


The ac compressor bracket bolts are to be torqued to 40 ft lbs, as far as the compressor itself you can just hand tighten bolts, there is no specs for compressor bolts just bracket, the bolts are just snug.

Aug 28, 2012 | Suzuki Aerio SX Cars & Trucks

2 Answers

Need to know torque specs for head bolts on a 2002 pontiac sunfire 2.2


Cylinder head bolt torque spec are

First Tightening Pass --- 22 Ft. Lbs or 30 N.m
Second Tightening Pass --- 155 Degrees

Here is the tightening sequeuce just in cause



best_try_17.jpg

Dec 23, 2010 | 2002 Pontiac Sunfire

1 Answer

I need torque specs to change a water pump for a 1999 chrysler cirrus 2.4 liter engine. water pump torque specs.


dont know the specs but you should be ok if you tighten the bolts snuggly and then 1/2 turn this will usually suffice just be careful not to over tighten

Nov 01, 2009 | 1999 Chrysler Cirrus

Not finding what you are looking for?
2002 Nissan Frontier Crew Cab Logo

Related Topics:

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...