Question about 1991 Honda Accord

2 Answers

I have a 1991 honda accord lx, i replaced the clutch and matser slave, as well as the brake booster and master on that also.. the brakes will pump up but if it sits they go straight to the floor any help

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Filmmaker:

    Uploaded 5 video answers.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

Need to bleed the brakes you have air in the lines.

Posted on Nov 24, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 202 Answers

Ok back to basics ,,,, there is a flexible brake hose at each wheel ,,,, clamp these off using a proper brake hose clamp ,( vise grips can damage the hose if too tight ) then u should have a rock hard brake pedal ,,, if master cyclinder is ok ,, release them one at a time and whichever one causes the drop to the floor is the area where the fault is ,,, then you strip that one and find the problem ,,,, but you need to be sure that the fault isnt caused by air in the system so i would bleed whichever clamp area which causes most pedal drop when unclamped

Posted on Nov 24, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

AlmostBob
  • 550 Answers

SOURCE: Replaced master cylinder

bleed the brakes there are bubbles in the lines the air compresses and does not transmit force very well

there is a bleed valve on each brake cylinder ...

here read this
http://en.wikipedia.org/wiki/Brake_bleeding

Posted on Aug 01, 2008

  • 5 Answers

SOURCE: 1991 Honda Accord brake light probelm.

Check the prones inside the connector that you plug into the brake light module. You may have to squeeze, wiggle, tilt each one to see which one is not connecting all that good. I know it may sound confusing. I tried to explain the best of I could.

Posted on Apr 29, 2009

  • 335 Answers

SOURCE: brake lock-up

I suspect that you have front disc and rear drum brakes.You did not say which of your brakes are locking up. I suggest that if your front brakes are locking {skid} that means your rear brakes are not engaging. If your rear brakes are locking {skid} then I suggest you have problems with park brake or brake fluid leaking onto the rear shoes.
More info would help me help you. I will check back soon.

Posted on May 21, 2009

  • 496 Answers

SOURCE: 1991 Honda Accord Brake Lights Stay on

Hi,
Usually there is a spring loaded switch that is activated by the brake pedal arm (under the dash). It registers on the pedal arm and when the pedal is depressed the switch is activated, causing your brake lights to illuminate.
The switch may have been bumped out of position. Hopefully this is a quick and easy fix for you...
Good luck!

Posted on Sep 22, 2009

Sean80000
  • 1867 Answers

SOURCE: 1994 hoda accord lx brakes

Please refer to the link below.

http://corp.advanceautoparts.com/english/youcan/asp/ccr/ccr20011001bb.asp

Posted on Dec 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1991 honda accord ex where does clutch fluid go


this is a 1991 honda EX engine bay
on the firewall
the smaller reservoir next to the brake master reservoir
26339433-tatvs1i0o052r0jcnodwvepi-1-0.jpg

26339433-tatvs1i0o052r0jcnodwvepi-1-1.jpg

Nov 03, 2016 | Honda Cars & Trucks

1 Answer

Trouble shooting my brakes on a 1996 honda accord lx


not enough information but if they're squeaking when your blood pressure replace the pads or shoes if they feel hard as a rock bad brake booster if there's spongy bad master cylinder vaya automotive repair book

Feb 26, 2015 | Honda Cars & Trucks

1 Answer

How to bleed clutch master cylinder on a 1995


It takes 2 people. Open the bleeder on the slave cylinder, hold your finger over it while the pedal is pumped, releasing the pressure when the pedal is down.. Once it starts pushing fluid thru, close the bleeder, pump 3 times, open bleeder with pedal down. Repeat till clutch feels good. If you are replacing the master cylinder, bench bleed it 1st. Be patient, this all takes awhile.

Sep 30, 2014 | 1995 Honda Accord

1 Answer

Cant locate clutch cylinder 1988 Honda accord lx 5 speed trasmssion


If it is a hydraulic clutch, and not cable operated, there will be two cylinders. A clutch master cylinder will be mounted on the firewall next to the brake master cylinder. One steel line will go from the master cylinder down to the slave cylinder bolted onto the transmission housing where the clutch lever extends out of the housing. Other than bleeding the slave cylinder, no adjustments are necessary on hydraulic clutches. Cable operated clutches have an adjusting mechanism to take up slack when the clutch disc wears. The adjuster will be inside the engine bay.

Sep 22, 2013 | 1987 Honda Accord

1 Answer

1996 honda accord 5 speed transmission stuck in gear


Let's look at your slave cylinder and your master cylinder.
Under the hood of your car are two master cylinders, and physically, they are close together.
They are found right in front of you as you drive the car, except they are under the hood and about chest high.
My 1990 has them right along side one another.
The brake master cylinder reservoir is about 4 inches in diameter, the clutch master cylinder reservoir is about 3 inches in diameter. Both of them take quality brake fluid.
Sounds like your clutch master cylinder is dry of brake fluid.
It would be nice if all you had to do was to add brake fluid to the "fill" line, but then you'd have air in that system, and it would need to be "bled" to work.
If you do find the brake fluid low, very likely the slave cylinder needs replacement, as your car is the right age to need this.
Be blessed.

Mar 18, 2013 | 1991 Honda Accord

1 Answer

My brake peddle keeps getting stuck, i replaced the master cylinder with a used one and the same result in about a week


check your brake booster .. while the car is off pump the brake til it gets hard start the car and see if it sinks down

Apr 13, 2010 | 1991 Honda Accord

1 Answer

Clutch sticks what should i do or check for the


First thing to check is the fluid level in the clutch slave cylinder resivoir,located just below the brake booster,drivers side.

Dec 14, 2009 | 1991 Honda Accord

2 Answers

Will not go into gear(manual)


Pretty good chance it's the clutch but check the clutch master cylinder and slave cylinder for leaks (also line between). A drastic change often is caused by failure of either component...generally if clutch fails, it is a gradual process (similar to how a brake pad wears)

Apr 03, 2009 | 1991 Honda Accord

1 Answer

Sticky clutch


slave cyl is sepreate from master cyl you have air in the clutch hydraulic system replace slave and inspect clutch master for leaks on drivers floor board area pull carpet back and make sure to bleed system properly!!!!!!!

Feb 26, 2009 | 1992 Honda Accord

2 Answers

1991 honda accord 5 speed


Sounds like you have a clutch problem. first thing to check is the fluid level in your clutch master cylinder, which is near your brake master cylinder for fluid level. It uses same fluid as brakes. See what you find out & get back if need more help.

Jan 23, 2009 | 1991 Honda Accord

Not finding what you are looking for?
1991 Honda Accord Logo

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...