Question about 2004 Honda Accord

1 Answer

Brake light and emergency flashers not workin g 0n 2004 honda accord

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 20,706 Answers

Check the fuses. in cab fuse box. open glove box, read the operators guide, it shows the fuses and which is which. fix brakes first.

what country???????????
not working means little.
out or stuck on, is better./?

both brake lights. out?
both emerg. out all ends of ca?r x 4? front and rear.????
what about blinkers (turns).? out? x 4? front and rear?//????
there are 3 electric systems sold on this car.
one 1 has simple brake lamp switch, and the export is very complex.
ive not a clue what country you reside (or car was sold new)
so cant guess. or advice, beyond a fuse check.


but on 2 of the 3, cars
the wt/tan wire at the brake switch.
if 0v and the fuse is good, #2
then the switch is bad or maladjusted.
if wt/tan wire is 12v brake appled
then the wire is cut to the rear of car... lamps.(harness)
this is common with trailer wiring hacks (uhaul hacks)










Posted on Nov 25, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: How to Change the brake light - 2004 Honda Accord

These are directions from Wiki plus my own recent experience. Open the trunk and look in the left or right corner closest to the rear of the car. You will see a 4x4 3/4 (approximate) plastic cover, pull firmly to remove the plastic piece (if covered) from the backside of the taillight. Pay attention to how it comes out too because you will have to match up the ends to put the piece back in correctly. My breaklight was the top lightbulb but you can locate the burned out bulb by pressing your breaklights (I used a stick to wedge the pedal). When you find the bulb that is burned out, twist the bulb by grabbing it at the plastic end (I had a little tab on mine to push in before I turned the bulb) and turn it counter-clockwise then pull it straight out of the plastic housing and replace it with a brand new light bulb.

Hope it goes as smoothly for you as it did for me!!
Brooke

Posted on Apr 11, 2009

  • 5 Answers

SOURCE: 1991 Honda Accord brake light probelm.

Check the prones inside the connector that you plug into the brake light module. You may have to squeeze, wiggle, tilt each one to see which one is not connecting all that good. I know it may sound confusing. I tried to explain the best of I could.

Posted on Apr 29, 2009

c17hydro
  • 2984 Answers

SOURCE: remove and replace rear brake shoes on 2004 honda

Brake Shoes Removal & Installation To Remove:

  1. Raise and safely support rear of vehicle.
  2. Remove rear wheel assemblies.
  3. Release parking brake.
  4. Remove brake drum.
Rear brake shoe assembly


6c57c70.gif
  1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
  2. Push retainer springs IN and turn to remove tension pins.
  3. Lower brake shoe assembly and remove lower return spring.
  4. Remove brake shoe assembly from back plate.
  5. Disconnect parking brake cable from lever and remove brake shoe.
  6. Remove parking brake lever from brake shoe.

To Install:

d36458c.gif
  1. Install parking brake lever to rearward brake shoe.
  2. Secure lever to brake show with a NEW U-clip.
  3. Pinch U-clip closed.
  4. Connect parking brake cable to rearward brake shoe.
  5. Install self-adjuster lever spring on front brake shoe.
  6. Assemble clevises, adjuster bolt and upper and lower return springs.
  7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
  8. Install brake shoe assembly onto back plate.
  9. Install tension springs.
  10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
  11. Install brake drum.
  12. Install rear wheel assembly.
  13. Lower vehicle.
  14. Adjust self-adjusting brakes by pressing brake pedal several times.

Posted on Jul 13, 2009

  • 2 Answers

SOURCE: Honda Accord Map Light bulb

the cover is removed straight down, slowly working it with a thin tool or butter knife. WD40 to front and rear edge (there's nothing medial or lateral). The cover has 2 Y clips on each side, one about half way, and one that clips straight off of the hinge post. There are no "tabs". It will eventually unclip straight down. Then can replace with a DE3175 LED bulb (V-LEDs.com)

Posted on Oct 29, 2009

  • 2841 Answers

SOURCE: My 2004 Honda Accord Brake and TCS light stays on.

I will assume you know there is a button on the dash to turn the TCS on and off. Make sure that button has not been pushed. The brake light can be on due to worn brake pads or low fluid level. If the TCS is not turned off then I suggest you take the car to a trusted mechanic or to your local Honda dealer and have it looked at. It takes skill, knowledge, and the proper tools to diagnose this type problem. It can be many things including a sensor, and you can spend lots of money guessing. Spend the money to have it repaired by someone who knows what they are doing. You will be money ahead and have it done right the first time.

Posted on Jan 15, 2010

Testimonial: "I went to a mechanic who told me it would cost $1,000.00 to replace the computer sensor. Or replace the brake fluid cap.!?!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Accord lost signal lights, and emergency flashers. Unable to find problem. All bulbs are good, and no blown fuses. HELP!!


replace flasher unit driver side, under dash, above fuse block, mounted on kick panel. Looks like picture below. Tell the parts store it runs both the turn signals and the hazards to make sure you get the right one.

jturcotte_73.jpg

Dec 16, 2010 | 1996 Honda Accord

1 Answer

2004 Accord, left turn signal out, no indicator on dash, replaced both bulbs. Does signal flasher have seperate circuits for left and right side?


No, no seperate system. Your problem is generally caused by a burned out bulb, bad ground at tail light. A bad flasher would affect both sides. Front and rear must be good. Ck flasher plug in. Good Luck

May 25, 2010 | 2004 Honda Accord

2 Answers

Brake lights stay on 1995 honda accord


the brake light switch on the top portion of the brake pedal is most likely bad and must be replaced

May 25, 2010 | 1995 Honda Accord

1 Answer

I have a 2004 Honda Accord and I cant move the shifter from parking to drive unless I use the button on hte console?


the nuetral safety switch is bad on the car this will not let you shift the car into gear if it does not register that the car is in park and your foot is on the brake pedal, try pulling the emergency brake on and see if it lets you.

Aug 24, 2009 | 2004 Honda Accord

1 Answer

2004 honda crv brake won't release


Your emergency brake is a mechanical brake system that is indipendant of the regular hydrolic system. If the red brake light on the dash is on make sure it's the emerg. brake and not a problem with the fluid level or the calapers sticking. the best way to check the emerg. brake is to rase both rear wheels off the ground and spin them. If they spin, the emerg. brake is not locked up. If they don't spin, take the rear tires off and the brake drums. (you may have rear disk brakes.) check the springs to insure they are all hooked up properly. If there is no problem there, follow the parking brake cable to check for damage. The cable is like a brake cable on a bike, If the inner cable is binding inside the cable sleeve,the brake wont release. If you have rear disc, it's probly a bad calaper.The park brake cable is attached to the calapers. Rember if it wont run it's annoying but if it won't stop, it's deadly. DON"T experiment with brakes!!! If in doubt, take it to a pro.

Apr 30, 2009 | 2004 Honda CR-V

2 Answers

Please my 1997 honda accord dash board brake lamp is on permanetly, what should i do


Check brake fluid level, check hand brake (emergency) is down & released all the way. Otherwise, have brakes checked a.s.a.p. in case of dangerous problem. Not something you want to ignore.

Mar 31, 2009 | 1997 Honda Accord

1 Answer

1998 Honda Accord EX


  1. check if the turn signels work. check the brake petal switch underneath the brake petal-also check the operation of the emergency flashers for operation. all of these items are related.

Aug 31, 2008 | 1998 Honda Accord

Not finding what you are looking for?
2004 Honda Accord Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...