Question about Toyota Camry

1 Answer

How do you clear the codes after you fix the problem

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 76 Answers

Hi there. you will need a diagnostics meter to reset error codes.
after repairs. best to take it to a garage. good luck

Posted on Apr 27, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you clear a code on a 2005 Artic Cat F7?


it should have cleared itself as you mentioned. you should be able to find a code chart online to figure out what it is and how to fix it. hardcoresledder.com is a good resource. try there for more help.

Jan 18, 2018 | Cars & Trucks

1 Answer

How dhowo you clear codes


A code reader/scan tool is the best way to clear codes. You can also disconnect the battery to clear the codes. If the loight comes back on it is a HARD code and the light will not go out until the problem is fixed

Jan 04, 2016 | Cars & Trucks

2 Answers

Ok had the codes come up for both crank sensors on our Pontiac Montana and knock sensor, replaced all three sensors cleared codes and the check engine light keeps coming back on after clearing codes, for...


I guess you do not know that OBD Codes have
nothing to do with replacing parts

The Codes are used along with the diagnostic
info & charts to check the system that set the codes

Only component testing will find a problem

You used the name of a codes to replace a part
with a similar name

I would guess you did no testing & have no idea why the
fault codes were set, so you found no problem, thus you
fixed nothing & the MIL Lamp is still on

You Cleared ALL DATA needed to help diagnose the issues

You lost your codes & freeze frame data at the time the codes
were set & your lost your emission monitor data

Now you get your codes & write them down
Google the codes & study the possible cause
& solutions

TYPE: OBD & your codes

Need to study OBD Vehicle Systems

Oct 16, 2014 | Cars & Trucks

1 Answer

P0455


clearing the code does not fix the problem it only clears the code untill the computer registers that a certain component is faulty.fix the faulty component this is what the codes are for.

Apr 14, 2013 | 2001 Dodge Dakota

2 Answers

How to reset computer when engine light is on so I can pass emissions on 2004 avalanche


Have you fixed whatever caused the code to come on? If not you will not be able to clear the code and pass emissions. Two reasons - 1. If the problem has not been repaired the check engine light will come back on. 2. Clearing the codes usual means that the OBDII monitors will also be cleared. There will be a code stored for this until the monitors are complete. If they see this co they know what you are up do and you do not pass.

Apr 09, 2013 | 2004 Chevrolet Avalanche

1 Answer

Clear all repair codes


Remove the negative battery cable for 10-15 minutes then reconnect. If there no active current codes then this will clear codes. If there any current problems the codes will come back. The problems must be fixed to clear all codes.

Sep 11, 2012 | 2000 Chevrolet Silverado 1500

1 Answer

How do I clear a code P0506 on Chevy Colorado 04'? Not fix, but simply clear to see if it returns.


did you try disconnecting the battery and then reconnect battery, it works a lot like a hard boot on a PC in fact that is what your doing to your cars computer

Dec 02, 2011 | GMC Canyon Cars & Trucks

1 Answer

I have a 2004 mazda rx 8 we may disconnect the battery to clear the "check engine light" -- if we do, will we need a "code" for the radio, or anything else?


You WILL probably need a code. Your car might not remember it as it needs the battery to keep memory. The best way to clear the check engine light is to buy a code reader. Costco has a cheepie one that works great. $35.00 . The code reader will also give you "code" that your car is throwing. Disconnecting the battery to clear the code is only a band-aid fix. If there is a problem with your car the "check engine light" will turn right back on. Just clearing the code obviously doesn't fix your problem.

Sep 26, 2011 | 2004 Mazda RX-8

1 Answer

Clear code for engine light


The code clearing happens via two things> first, resolve the issue causing the error code. The code will come back if you do not resolve the issue. you can clear the codes by using a code reader, but it woudl likely reappear. Fix the issue causing the error code.
Remember, the code is a clue, not always the issue.

Mar 02, 2011 | 2004 Mitsubishi Endeavor

1 Answer

How to clear codes


when problem is fixed codes will clear themselfs if problem isnt fixed codes will come right back

Dec 10, 2010 | 1995 Subaru Legacy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...