Question about Toyota Land Cruiser

1 Answer

Reset diesel filter sensor - Land Cruiser Toyota Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 954 Answers

Switch the ignition to OFF.
Disconnect the fuel filter warning lamp switch connector.
CAUTION: Never depress the brake or clutch pedal.
Switch ignition to ON. and wait for 3 seconds.
Next during the 57 seconds re-connect the fuel filter warning lamp switch connector.
After further 3 seconds the fuel filter warning lamp will go OFF, or the message "Fuel filter maintenance required" will be cleared off from the display and the re-set is complete now.
Switch OFF the ignition switch.

Posted on Dec 19, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Accidentally put unleaded fuel instead of diesel in 2013 D22 drove approx 10k


Drain the fuel out and flush the fuel lines and the filter. Failure to purge the unleaded fuel from the system can destroy the engine due to severe pre ignition.

Feb 18, 2017 | Cars & Trucks

1 Answer

What is fault code 2003 on a mitsubitsi colt 3000i


Diesel particulate filter efficiency below threshold bank 2
Possible causes
Exhaust pressure sensor fault
Diesel particulate filter faulty
C/heck/replace exhaust pressure sensor
Check/replace Diesel particle filter

May 31, 2016 | Cars & Trucks

1 Answer

Why genset not starting.


you say diesel so I assume that it is a diesel engine
The symptoms indicate low pressure in the fuel pump and that can be from air in the system or blocked filters
you mentioned deep sea controller so is it right to say that it is on a boat
If so then check the fuel tanks for a black moss like substance
this causes filter blockages and eventually gets to the pump and injectors and creates hard start problems
if so empty the tank and clean out as best you can
regularly use diesel fuel conditioner to stop the moss regrowth
It comes from condensation in the diesel tank and is a common problem in tanks that are left standing partly empty or with low fuel in them

May 25, 2015 | Cars & Trucks

1 Answer

Need to fix my 2007 Dodge Ram 3500 dually,6.7 Cummings diesel, check engine light code P2002


P2002 - Diesel Particulate Filter Efficiency Below Threshold (Bank 1)
Description: The powertrain control module(PCM) monitors the efficiency of the diesel particulate filter for a concern. The efficiency of the filter is determined by the amount of restriction in the filter for a certain exhaust flow rate. The diesel particulate filter is preconditioned for 5,000 km (3,107 miles) before the PCM begins to monitor the level of restriction. The test fails when the measured level of restriction is less than the expected level calculated by the PCM. Possible Causes:
  • Dirty air cleaner element
  • Recent manual or thorough diesel particulate filter regeneration
  • Aftermarket accessories and performance modifications
  • Modified tailpipe
  • Exhaust leaks before or near the diesel particulate filter pressure sensor
  • Leaks in the diesel particulate filter pressure sensor connecting hose
  • Damaged diesel particulate filter
Diagnostic Aids: Check for leaks in the exhaust system. Check for aftermarket exhaust accessories and performance modifications that decrease the exhaust restriction. If a new diesel particulate filter was recently installed, verify the diesel particulate filter parameter reset procedure was carried out.

Feb 18, 2015 | Dodge Cars & Trucks

3 Answers

Toyota hilux d4d 3.0 litre fuel system light reset ?


Remove the key from the ignition but keep it handy. Important: Disconnect the negative terminal of the battery for longer than 90 seconds to prevent the risk of having the airbags deploy! Replace the diesel filter (Follow the instructions that can be found in Toyota service manuals (search www). Remove the diesel filter sensor cable (the one on top of the filter assembly). Make sure the new O-rings seat properly. Close the filter assembly by turning the locking ring until it clicks. Bleed the filter assembly by pushing the little plunger thing on the top of the assembly until pumping becomes difficult. Connect the negative back onto the battery. Insert the key in the lock and turn until the dashboard warning lamps come on, but do not start the car yet. Within 3 to 60 seconds of doing this re-connect the diesel flter sensor cable. The light should be extinguished. Obviously there could be another problem causing the light to remain on (not flashing - steady on). If the light is flashing, then you have water in the system and should follow the answer supplied elsewhere by someone else to drain the water. Now start the car and enjoy clean diesel fuel driving. You should really not wait for the light to come on steady before chnaging the filter. Some fanatics believe every 10,000km is the longest you should wait, but this depends on fuel quality, low or high sulfur content, etc. Rather do it more frequently than having to buy new injectors.

Apr 10, 2012 | 2007 Toyota Hilux 2.7

1 Answer

Are there exhaust sensors or are they called probes? on 2008 ford f250 6.4 turbo diesel


THERE ARE SEVERAL SENSORS:

EXHAUST GAS TEMPERATURE (EGT) SENSOR
EXHAUST PRESSURE (EP) SENSOR
DIESEL PARTICULATE FILTER PRESSURE SENSOR

HOPE THIS INFORMATION HELPS

Oct 17, 2010 | 2008 Ford F 250 Super Duty 4WD

1 Answer

Volkswagon carravelle failed m.o.t on gas emmisions tried lamba sensor no improvement any ideas. 1995 model


is it petrol or diesel?-if its petrol try removing air filter-if its diesel you will have to change oil filter,oil,oil filter and fuel filter in one job lot-this usually works! if not as a last resort find the diesel screw on the fuel pump and turn it down(anti clockwise i think)-note how many turns-you will notice a horrible loss in power,but you can reset it after the test,because no-one will care then

Feb 25, 2010 | Volkswagen Camper Cars & Trucks

1 Answer

I have a 1997 f350 turbo diesel and the water in fuel light is on.i replaced the restriced fuel filter sensor(vacuum switch)cleaned the filter pot and replaced the filter and new diesel what elese can i...


You have to drain the water out of the fuel tank. There should be instructions on how to do that in your owner's manual. The sensor is in the tank. Hope this helps.

Dec 29, 2009 | 1997 Ford F250 SuperCab

1 Answer

Chevrolet 2500 Not Running, May Be Fuel Filter Sensor


if it dont have good compression it will not start check the comp and make sure there no water in oil if fuel pressure is low it will not pop the injector open try some starting fluid

Dec 18, 2008 | 2001 Chevrolet Silverado 2500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...