Question about 1998 Chevrolet Blazer

1 Answer

All tail lights on 1999 GMC Denali stopped working at the same time, is there a brake lamp relay

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 170 Answers

Checked fuses? Tail light bulbs? Brake light switch? Flasher?

Posted on Nov 23, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 85 Answers

SOURCE: 98 Chevy pickup brake lights just stopped working

have you tried to find the brake pedal switch? follow the brake pedal under the dash and there should be a switch that the brake pedal presses to activate the lights when you push it in . if everything else has been checked then I suspect that the switch has moved enough to not work or it may be just bad. let me know if this was it.... hope this works

Posted on Jun 17, 2009

  • 16 Answers

SOURCE: ''96 Silverado no tail lights.

if that doesn't help, you might want to check the bulbs. the damage might have shorted which burned out the bulbs. but you do have one wire that runs to the rear and splits off to the tail lights. the wire should run back to the head light switch via a fuse. the headlights have its own relay. but i hope it is just a fuse.

Posted on Dec 11, 2008

SOURCE: Tail lights don't work on 1998 Chevy Silverado.

check the wiring from the tailights back to the fuse panel, it sounds like an open connection. if i recall correctly check under the dash on the drivers side near the fuse panel for a bunch of wires in a bundle and look carefully for a wire or two that are cut/shorted/or seperated, you can also check under the drivers side kick panel by the hood release.

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All tail lights on 1999 GMC Denali not working, is there a brake lamp relay


yes its in the taillight itself. But before you do that check the prongs in the socket to make sure they are getting a good connection. This is a common mistake on general motors period.

Nov 23, 2013 | 1998 Chevrolet Blazer

1 Answer

No brake lights on 1999 gmc k3500


Where the brake lamp attatches to is called a tail lamp assembly,some call it a rear light module,they are sold in pair and they do fail,you did the brake switch and the combination switch,either the wire is disconnected some how or the lamp assemby both side failed,

Dec 09, 2012 | Cars & Trucks

1 Answer

1999 Yukon Denali stop shifting out of park.


Check the brake lights when this happens, if they are not on then you have found the problem it is the brake light circuit. Go under the dash if the brick lights don't work and check the brake light switch above the brake pedal, it should have 12 volts in and out with the brake pedal pushed down. See typical brake light switch location below. #4 in diagram is brk lite switch.
10_12_2012_2_06_31_am.gif

Oct 11, 2012 | 1999 GMC Yukon Denali

1 Answer

2002 gmc yukon denali xl, cruise control inop after installing l.e.d. taillamp assemblies, know it is a resistance problem, where and what rating of resistor should i install?


It is not a resistance problem. As it operates normally, the cruise control is wired to the stop lamps and will operate only when it sees chassis ground through the stop lamps. When you tap your brake pedal, 12 volts is applied, the ground goes away and cruise is deactivated. Because the LED tails are diodes and only let current flow one way, the cruise cannot see ground and will not set or operate. The same symtoms would appear if you had original incandescent tail lamps and both brake lights were burned out.
The solution will be finding the wire from the cruise that senses the brake lights, and connecting it directly to the brake switch, IF the brake switch is grounded when the pedal is not pressed. You may have a relay wired to the brake pedal switch to make this happen. Seek a knowledeable car audio/accesory shop familiar with auto electrical to help you with this.
Good luck!

May 02, 2010 | 2002 GMC Yukon Denali

1 Answer

99 gmc denali dash light, parking lights, tail lights, and dash light dont work. Interior lights, brake lights, blinkers, headlights work Turning on the headlight switch blows number 15 drl-fog fuse...


You have a short to ground somewhere in the drl-fog lamp circuit. Check for obvious wiring connector or wiring to drl & fog lamps. check wiring for pinched or broken wires coming from sockets. If you don't find problem, you can trace wiring from lamps to main harnesses and hopefully find source of short.
hope this helps.

Mar 02, 2010 | 1999 GMC Denali

4 Answers

Brake lights won't work. tail lights do. I


need to know if your third brake light up high is working or not.if it isn't,you need to check the brake light switch on the brake pedal with a test light,one side hot all the time,the other side should turn hot when brake pedal is pushed.

Jan 19, 2010 | 2002 GMC Envoy XL

1 Answer

Brake lights only show on center 3rd high stop tail lamp


Yes, the flasher does interrupt the brake signal. you do know that this is a push on, push off switch. Some try to pull this switch to turn off flashers, but, it has to be pushed again to turn off.

Nov 30, 2008 | 1999 GMC Suburban

1 Answer

Brake lights and crusie don't work


1ST THING TO CHECK IS THE STOP LAMP FUSE . FUSES LOCATED LH SIDE UNDER HOOD. THIS FUSE ALSO POWERS THE ACC. CIRCUT IN TRUCK. ALOT OF TIMES, LAP TOPS, DVD PLAYERS ETC. OVERLOAD CIRCUT & FUSE BLOWS.

Oct 25, 2008 | 2002 GMC Yukon Denali

1 Answer

2002 YUKON XL Denali no brake lights or cruise


FROM LUSTY KID:

Check your bulbs first, I have lost both headlights on my ford at once on account of the bulbs burning out at the same time. Same thing probably happen, you have one filament out. The lights can work, but if the filament for brake is burnt, you don't see brake lights.

As for the cruise control. Check fuse box first. If OK check vacuum hose to actuator in engine compartment for starters.
Advise:

Oct 12, 2008 | 2002 GMC Yukon XL

Not finding what you are looking for?
Cars & Trucks Logo

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...