Question about 1998 Chevrolet Blazer

1 Answer

All tail lights on 1999 GMC Denali not working, is there a brake lamp relay

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Yes its in the taillight itself. But before you do that check the prongs in the socket to make sure they are getting a good connection. This is a common mistake on general motors period.

Posted on Dec 18, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: ''96 Silverado no tail lights.

if that doesn't help, you might want to check the bulbs. the damage might have shorted which burned out the bulbs. but you do have one wire that runs to the rear and splits off to the tail lights. the wire should run back to the head light switch via a fuse. the headlights have its own relay. but i hope it is just a fuse.

Posted on Dec 11, 2008

SOURCE: Tail lights don't work on 1998 Chevy Silverado.

check the wiring from the tailights back to the fuse panel, it sounds like an open connection. if i recall correctly check under the dash on the drivers side near the fuse panel for a bunch of wires in a bundle and look carefully for a wire or two that are cut/shorted/or seperated, you can also check under the drivers side kick panel by the hood release.

Posted on Feb 17, 2009

djicenova
  • 319 Answers

SOURCE: brake lights don't work fuse blows right away?

Check Trailering Wiring

Posted on Mar 03, 2009

emissionwiz
  • 77169 Answers

SOURCE: 2001 Chevy Lumina brake lights not working

test and replace the brake light switch, it is located at the top of the arm the brake pedal is attached to.

Posted on Mar 26, 2009

  • 85 Answers

SOURCE: 98 Chevy pickup brake lights just stopped working

have you tried to find the brake pedal switch? follow the brake pedal under the dash and there should be a switch that the brake pedal presses to activate the lights when you push it in . if everything else has been checked then I suspect that the switch has moved enough to not work or it may be just bad. let me know if this was it.... hope this works

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No rear running lights. Turn and brake lights work. what do I do


The tail lights are also called parking lights.
There is a 10amp fuse for each rear parking lamp. The fuses are in the rear fuse box. Your owner's manual will tell you where that fuse box is located.
The fuses get power from a park lamp relay.

Sep 30, 2012 | 2005 GMC Envoy

1 Answer

My tail lights dont work or break lights but when i depress the break pedle my cargo break light works...i drive a 02 GMC serrira....my hazards, turn signals, and back up lights work


It sounds like you have burnt out bulbs. All those other lights that you say work are all different bulbs. The tail light bulbs have dual filament so that they can perform the tail light and brake light function. You should change out your bulbs and that will probably solve your problem.

Dec 03, 2010 | 2002 GMC Denali

1 Answer

2002 gmc yukon denali xl, cruise control inop after installing l.e.d. taillamp assemblies, know it is a resistance problem, where and what rating of resistor should i install?


It is not a resistance problem. As it operates normally, the cruise control is wired to the stop lamps and will operate only when it sees chassis ground through the stop lamps. When you tap your brake pedal, 12 volts is applied, the ground goes away and cruise is deactivated. Because the LED tails are diodes and only let current flow one way, the cruise cannot see ground and will not set or operate. The same symtoms would appear if you had original incandescent tail lamps and both brake lights were burned out.
The solution will be finding the wire from the cruise that senses the brake lights, and connecting it directly to the brake switch, IF the brake switch is grounded when the pedal is not pressed. You may have a relay wired to the brake pedal switch to make this happen. Seek a knowledeable car audio/accesory shop familiar with auto electrical to help you with this.
Good luck!

May 02, 2010 | 2002 GMC Yukon Denali

1 Answer

99 gmc denali dash light, parking lights, tail lights, and dash light dont work. Interior lights, brake lights, blinkers, headlights work Turning on the headlight switch blows number 15 drl-fog fuse...


You have a short to ground somewhere in the drl-fog lamp circuit. Check for obvious wiring connector or wiring to drl & fog lamps. check wiring for pinched or broken wires coming from sockets. If you don't find problem, you can trace wiring from lamps to main harnesses and hopefully find source of short.
hope this helps.

Mar 02, 2010 | 1999 GMC Denali

4 Answers

Tail lights do not work. Bulbs are good. Both fuses are good(separate cicuits). What else could it be? Is there a relay involved? Could the switch be defective? thanks! Mike


All the exterior lights run threw the turn signal switch. Except the high mount brake light. If you are talking about brake lights replace the TS switch. Parking lights are a little different. If you have no parking lights front and back, TS switch. If you have front and no back, ground problem. Grounds for the back are usually on the drivers side mounted to the frame.

Aug 01, 2009 | Hyundai Motor 2005 XG350

1 Answer

Brake lights and crusie don't work


1ST THING TO CHECK IS THE STOP LAMP FUSE . FUSES LOCATED LH SIDE UNDER HOOD. THIS FUSE ALSO POWERS THE ACC. CIRCUT IN TRUCK. ALOT OF TIMES, LAP TOPS, DVD PLAYERS ETC. OVERLOAD CIRCUT & FUSE BLOWS.

Oct 25, 2008 | 2002 GMC Yukon Denali

1 Answer

Fuse panel


PARK LP Fuse #12
30A
Park Lamp Relay, Headlamp and Panel Dimmer Switch-Park Lamps
Have you towed a trailer? if so maybe the trailer wiring is shorted.

Oct 02, 2008 | 2002 GMC Yukon Denali

Not finding what you are looking for?
Cars & Trucks Logo

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...