Question about Cars & Trucks

Open Question

Change a mass air flow sensor on dodge 6.7 liter diesel

How to change a mass lair flow sensor on a dodge 6.7 liter cummins

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

autodr
  • 260 Answers

SOURCE: Cleaning the Mass Air Flow Sensor

i will try to help. 171/174 indicates lean condition in engine. the mass air flow sensor is located in the rubber tube going to throttlebody. you can try to clean it. using mild carb cleaner safe for sensors, remove sensor from tube. spray clean the tiny wires located in the cylinder. do not touch them, they are very delicate. these engines are also notorious for leaking intake gaskets and faulty pcv valves. these will all set these 2 codes. feel free with anymore questions.

Posted on Nov 15, 2008

  • 39 Answers

SOURCE: mass air flow sensor bad on 2002 monte carlo ss

It's should be a simple remove and replace. Just make sure the engine is off. Also do not touch any of the filament wires on the sensor, just the plastic housing. Also after you install it drive the car for a little while (city speeds, cruising speeds and inbetween). That way the computer will be able to readjust its setting since it is a new sensor.

Posted on Apr 02, 2009

  • 1 Answer

SOURCE: Cold Air Intake - Mass Air Flow Sensor Adapter

i have a 91 mx6. the intake is all cattywompus and im just goin to take a piece of metal and tube and cut a hole in the peice of metal and weld the tube to it take my stupid box out and run that pipe staight to a coupling and then to the cone air filter. BAM!!!! problem fixed... i maight be able to fix yours too... e-mail me ajjordan64@hotmail.com. k?

Posted on Apr 16, 2009

  • 701 Answers

SOURCE: where is oil pressure sensor located on 2001 dodge 2500 cummins?

Hello mhak330: My name is Roger and I can give you the answer to your question. Locate the ECM on the drivers side of the engine.look for the bottom bolt holding the ECM. To the right of the bolt you should see the oil pressure sender unit. Should you need further help please just ask. Please rate the quality of your answer. This way we know you received helpful information. Thank You for using Fix Ya. Roger

Posted on Jul 07, 2009

  • 66 Answers

SOURCE: 2002 mazda millenia mass air flow sensor

Look in the oulet air cleaner tube, it's hold by 4 nuts.

Posted on Sep 16, 2009

Testimonial: "Thank you so very much for your assistance. I wish i could ask you alot of other questions!!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 GMC 4500 Diesel Truck - code P0039..At random intervals the engine will drop to idle and CEL illuminates. The throttle will not operate. what sensors I should replace and it what order? Thanks


Dodge Cummins Error Codes List - Diesel Bombers



www.dieselbombers.com > Dodge Cummins > Dodge Diesel Tech Articles

Apr 6, 2009 - It appears to have every CEL code known to man... or at least known to Dodge. ... Chevy/GMC Truck and Duramax Turbo Diesel Forum · Chevy/GMC Duramax... General · 2011 · 2013+ · 2007.5 - 2012 LMM · 2006 - 2007 LBZ .... P0039 Turbo/Super Charger Bypass Valve Control Circuit Range/Performance

Aug 23, 2015 | GMC Cars & Trucks

1 Answer

P0068 on a 2006 Dodge Ram 1500 SLT. Rough "hunting" for idle. Momentary lag/loss of power from a stop. Random RPM changes while at a constant speed. Sometimes it feels like it drops out of gear...


P0068 Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of power
- Engine rough idle Possible causes - Large vacuum leak
- Leaking air duct system
- Mass Air Flow (MAF) poor electrcial connection
- Manifold Absolute Pressure (MAP) poor electrcial connection
- Faulty Mass Air Flow (MAF) sensor
- Faulty Manifold Absolute Pressure (MAP) sensor
- TP sensor not seated properly.
- Faulty Throttle Position (TP) sensor.
- Dirty throttle body
When is the code detected? The Powertrain Control Module (PCM) monitors operation rationality check by comparing sensed throttle position to mass air flow readings
P0068 DODGE Description The Powertrain Control Module (PCM) monitors a vehicle operation rationality check by comparing Throttle Position (TP) to Mass Air Flow (MAF) readings. If, during a self-test, the comparison of the TP sensor and MAF sensor readings are not consistent with the calibrated load values, the test fails and a diagnostic trouble code is stored in continuous memory.

Jul 10, 2011 | Dodge Ram 1500 Cars & Trucks

2 Answers

Location of maf sensor 2001 chevy tracker v6


the mass air flow is part of the throttle body assembly. its where the big air hose from the air filter hooks to on the motor. here is a picture to aid you. hope this helpsonetufshoppe_114.gif

Feb 10, 2011 | 2001 Chevrolet Tracker

2 Answers

97' TAURUS SHO 3.4 LITER HAVE THE CODE PO102 NEED TEST PROCEDURE TO FIX


inspect Mass air sensor, clean with electrical cleaner and test. should read around 3 on scanner and jump to 15-20 upon accelaration if not replace.

Apr 09, 2010 | 1997 Ford Taurus

1 Answer

Mass air flow sensor replacement


Removing air box and tube leading to air flow sensor. Should just be a few screw like clamps. Make sure to hook wires back up exactly as removed. very easy replacement

Mar 09, 2010 | 1992 Dodge Spirit

1 Answer

I have a 2004 f-150 5.4 liter with 100,000 niles


When was the last tune-up?

Inspect few plugs for carbon ash (lean running) or wet (rich running).

Clean Mass Air Flow sensor with CRC Mass Air Flow Sensor cleaner

Change air filter

Change PCV valve (under $10 item)

Ran a tank of Chevron gas with LUCAS fuel system cleaner additive.


Inspect for vacuum leak.
Start from the brake booster (round metal drum) and work you way outward.

Jan 27, 2010 | 2004 Ford F150

1 Answer

1999 Dodge Ram 1500 Pickup error code p0171


This code means that system to lean, bank 1.
some of the possible causes to make this code set are
1. intake or exhaust leak,
2. problem with the air system.
3. MAF (Mass Air Flow sensor)VAF sensor (Volume air flow sensor)
4. fuel pressure/pump
5. injector(s)
6. HO2S (Oxygen sensor)

Sep 15, 2009 | 2003 Jaguar Vanden Plas

3 Answers

Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel


I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Mar 25, 2009 | 1996 Dodge Ram 3500 Club Cab

1 Answer

I have a 2000 ford f800 with a 5.9 cummins diesel engine it starts up and surges then dies and thats all it will do i also have no pedal response, i have tried a new injection pump and pickup pump,and...


did you try the mass air flow sensor? This same thing happend to my 2000 explorer this summer and that is exactly what ir was. try to unplug it and see if it will run on it's own then you can get it to a garage :)

Sep 19, 2008 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...