Question about Cars & Trucks

1 Answer

How do I reset the system in my 2007uplander - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 90 Answers

Fastest way to reset computer is to disconnect the battery for 2 to 3 minutes then reconnect the system will reset automaticly.

Posted on Nov 23, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How reset computer 2007 lincoln towncar


It is the same as this

Resetting a Vehicle Anti-Theft System
This is how you reset an anti theft system if you have the anti-theft light on, or your car is cranking, but you have no spark.

Doing a full reset of the anti-theft system.

Disconnect both battery leads for at least two hours.
Hold the negative and positive leads together for 5 minutes to fully discharge any power.
Put the key in the ignition, but not turned on. VERY IMPORTANT!
Connect the positive lead.
Connect the negative lead in one swift movement.
Wait 15 minutes for the system to fully reset.

Resetting Vehicle Anti Theft System

Jan 20, 2018 | Lincoln Cars & Trucks

1 Answer

How to reset the coolant sensor


There are 2 different procedures used to reset PCMs; depending on whether the vehicle has the older OBD1 emission control system; or whether it has the OBDII system. With the older OBD1 system; the PCM could be reset by disconnecting the battery for several minutes. But the later model OBDII system cannot be reset that way. It requires connecting an OBDII compatible code scanner to the vehicle, and using the scanner to reset the PCM. --------------------------------------------------------------------------------------
FGtech V53

Mar 21, 2013 | 1999 Buick Century

3 Answers

NEED TO RESET OIL CHANGE LIGHT


How to Reset the Engine Oil Life System
The Engine Oil Life System calculates when to change the engine oil and filter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE ENGINE OIL SOON message being turned on, reset the system.
Always reset the engine oil life to 100% after every oil change. It will not reset itself. To reset the Engine Oil Life System:
Display the OIL LIFE REMAINING on the DIC.
Press and hold the SET/RESET button on the DIC for more than five seconds. The oil life will change to 100%.
If the CHANGE ENGINE OIL SOON message comes back on when the vehicle is started, the Engine Oil Life System has not reset. Repeat the procedure.
Good luck and thanks for your question and I hope my suggestions help. burdfrenzy
Visit My eBay Store!
http://stores.ebay.com/Pittsburgh-Joes-Pants-Nat

Jan 03, 2011 | 2008 Chevrolet Impala

2 Answers

How to do I reset the maintenance service light on my 2007 Chevy Trail Blazer


there is no light for emissions testing on this vehicle. there is a ses light that can come on, indicationg a problem with the engine or transmission electronic system. this will require a scan tool to pull trouble codes. there is another light called oil life monitoring that needs to be reset after oil changes, which I suspect is what you are seeing. here is a picture of the light and the instructions for resetting.,

The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL SOON message being turned on, reset the system.
After changing the engine oil, the system must be reset as follows:
  1. Turn the ignition to RUN, with the engine OFF.
  2. Press the information and reset buttons on the Driver Information Center (DIC) at the same time to enter the personalization menu.
  3. Press the information button to scroll through the available personalization menu modes until the DIC display shows OIL LIFE RESET.
  4. Press and hold the reset button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
  5. Turn the key to LOCK.
If the CHANGE ENGINE OIL message comes back on when you start the vehicle, the Engine Oil Life System has not reset. Repeat the reset procedure.



485d3b2.gif

Sep 09, 2010 | 2007 Chevrolet TrailBlazer SS

2 Answers

How do i reset the oil life on a 2005 gmc c8500


Most often you need a code reader with a reset function that can connect to the computer jack under the dash and reset factory functions like that. Pain in the tush if you are changing your own oil. Mechanics and dealers have the equipment to do that reset.

May 20, 2010 | 2006 Chevrolet Silverado 3500

1 Answer

How do you turn off the oil change message in the 2002 ford explorer after the oil has been changed?


FROM YOUR OWNERS MANUAL:
To reset the oil monitoring system to 100% after each oil change
[approximately 8,000 km (5,000 miles) or 180 days] perform the
following:
1. Press the SETUP control to
access the System Check function.
2. Press and release the RESET
control to display “OIL LIFE XX%
HOLD RESET NEW”.
3. Press and hold the RESET
control for 2 seconds to display “IF
NEW OIL HOLD RESET”.
4. Press and hold the RESET
control to display OIL LIFE SET TO
100%. Your oil life is now reset.
To reset the oil monitoring system to your personalized oil life %:
1. Press the SETUP control to
access the System Check function.
2. Press and release the RESET
control to display “OIL LIFE XX%
HOLD RESET NEW”.
3. Press and hold the RESET
control for 2 seconds to display “IF
NEW OIL HOLD RESET”.

Apr 15, 2009 | 2002 Ford Explorer

3 Answers

2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on


Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Apr 02, 2009 | 2007 Ford Explorer Sport Trac

1 Answer

2005 ford freestar reset light on


Vehicles Without Message Center To reset the system, press and hold the odometer reset button and wait for the "TIRE PRESSURE SET" light to illuminate. Continue to press the button for 3 seconds, then release. After 3 seconds, the low tire pressure warning lamp will flash 3 times, indicating that the low tire warning system reset procedure is complete.
Vehicles With Message Center To reset the system, press and hold the SETUP button and wait for the message center to display "REST FOR SYSTEM CHECK". Then press the RESET button and wait for the message center to display "HOLD RESET TO RELEARN". Press and hold the RESET button for 3 seconds. The message "HOLD RESET TO RELEARN" and the low tire warning lamp will flash 3 times, indicating the reset procedure is complete.

Mar 12, 2009 | 2005 Ford Freestar

1 Answer

Nedd to know how to reset change engine oil light


Try this....

To reset the light, turn the key to the Run position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the Change Oil Soon light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset. If it does not work using the accelerator pedal, go under the hood and move the linkage manually to reset the system

Feb 18, 2009 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...