Question about 2003 Saturn VUE

1 Answer

I have a problems with code po124 3.0 6 cilinders

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 202 Answers

Code says throttle/ pedal position sensor,,, but be careful it could be the pedal sensor or thethrottle body ,,, im afraid you need it plugged in for a diagnostic to read the data list to see which sensor is reading incorecct

Posted on Dec 01, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda tribute 2008 4 cilinders,code 732. And the temperature gauge is going up and down in highway. A wrench light is on in the panel.


check for a viscous fan hub problem or electric fans fault
run the fault codes
check for water in the radiator ( not the reservoir)

May 04, 2015 | 2008 Mazda Tribute

1 Answer

P0303 code cilinder 3 misfire


Posible causes:
- Faulty spark plug or wire
- Faulty coil (pack)
- Faulty oxygen sensor(s)
- Faulty fuel injector
- Burned exhaust valve
- Faulty catalytic converter(s)
- Poor compression
- Defective computer

Read more at: http://www.obd-codes.com/p0303
Copyright OBD-Codes.com

Jan 18, 2014 | Renault Cars & Trucks

1 Answer

I HAVE PROBLEM WHITH A MAZDA TRIBUTE 2002.IA SIX CILINDER ONLY FOUR CILINDER ARE WORKING WELL AND TWO HAVE MISSFIRE


Please post your question in the proper forum. This does not have to deal with PC Desktops.

Jun 04, 2011 | 2002 Mazda Tribute

1 Answer

Welke injectoren moet ik gebruiken in mijn mercedes v280 waar een vw motor vr6 in zit? passen daar ook de injectoren uit een auto met een cilinder 2.9 in? Mijn auto is met een cilinder 2.8.


Welcome to fixya

Hello


I have a solution for this


What seems to be the problem?


Press Ok, Accept or replay so we may get started


My name is Bruce

Jan 14, 2011 | 1995 Volkswagen Passat

1 Answer

2004 audi a4 1.8 t misfiring flt code p0301 changed coils spark plug still showing code for cyl 1


try find out on the internet wats the problem with that code but take out the spark plug out of no 1 cilinder conected to the coil and turn over the engine and u will see if the spark plug will spark or not if is not sparking and the spark plugs and the coils are new may be from a wire or loose conection

Jan 12, 2011 | 2002 Audi A4

1 Answer

1999 lincoln navigator fault code


Your cilinder 2 sensors are going wacky. located close to the cilinder itself. you may need to replace them chec your repair book for specific locations. Thenget a OBDII reader to erase code. Some autos if you disconnect your battery cable for a few may reset it to stop the blinking.

Jun 30, 2010 | 1999 Lincoln Navigator

1 Answer

1999 Jeep Wrangler - Clutch pedal feels soft. Does not feel like it is fully disengaging when pressed. Hard to get into any gear when Jeep is not moving.


HALLO
CHECK BRAKE FLUID IN CLUTCH CONTEINER. IF IT IS MISSING, ONE OF CLUTCH CILINDER IS BROKEN.FIRST CHECK IF INSIDE THE CAR BEHIND CLUTCH PEDAL CAN BE SPOTED SOME BREAKE FLUID FROM CILINDER. IF EVERITHING IS "DRY", YOU HAVE PROBLEM WITH CILINDER ON TRANSMITION. ON SOME MODELS ARE OUTSIDE GEARBOX AND EASY TO CHANGE, BUT SOME HAVE BUILT IN CILINDER IN CLUTCH BEARING. IN THAT CASE YOU HAVE TO REMOVE GEARBOX, REDUCTOR...CHANGE CLUTCH TOO

MARKO

Oct 23, 2009 | 1996 Jeep Cherokee

1 Answer

Lifters noisey


the european ford escort '80-'86 had similar problems with that. problem is the hydraulic lifter cilinder burned engine oil settle inside those cilinders you have to remove the Camshaft you will find them and press them in with a little force and keep it overnight in a bucked of diesel to clean them up .blowdry them and put them back in the engine. check on damages while they are dry. they have to move when you aply pressure with your hands
WARNING when you start the engine because these cilinders are empty.your engine will make a hell of a noise .DON't be ALARMED this will go away in 1 or 2 minutes success

Jul 30, 2009 | 2001 Dodge Ram 2500 Truck

2 Answers

Loss of power


Do you know how check if every cilinder is working? with the engine in idle, go to the distribuitor cap and carefully unplug one at the time, every cilinder spark plug wire,in the cilinder you dont see a diference in rpm variation, that cilinder is not working, replace spark plug, if you see spark jumping fron the distribuitor cap torch the spark plug wire, another cause to a cilinder fail could be a loss of compression in one or more cilinder

Oct 29, 2008 | 1994 Toyota Pickup

Not finding what you are looking for?
2003 Saturn VUE Logo

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...