Question about Cars & Trucks

Open Question

How to replace gasket inlet manifold ef xr6 - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: air leak on inlet manifold gasket

ive got a vw bora 2.3 v5 2001 got a hissin from inlet manifold

Posted on Aug 15, 2009

Ad
  • 14 Answers

SOURCE: intake manifold gasket replacement? radiator has a

nah its pretty simple for the upper intake. 10 to 12 bolts.

Posted on Oct 13, 2009

co7196
  • 3433 Answers

SOURCE: I have a Pontiac grand am gt 2001 V6 I was

yes, I believe so. Not on it but in the female part.

Posted on Nov 02, 2009

clifford224
  • 1975 Answers

SOURCE: inlet manifold gasket what does it look like

I gave you the pictures of the intake manifold gaskets for both the 4 cylinder and 6 cylinder for that year. You really won't be able to see them just by looking for them as they will be between your intake manifol and where the intake manifold mounts to the engine but this is what you asked for. I hope this helps and good luck. Here are your pictures


clifford224_115.jpgclifford224_116.jpg

Posted on Mar 02, 2011

alicantecoli
  • 22219 Answers

SOURCE: Hi, I can't loosen the inlet manifold bolts

would help if knew what model and year this vehicle was or is ,have you tried to put engine oil on the bolts as this works better than any spray stuff

Posted on May 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Water on spark plugs on starting is it a blown gasket


not necessarily
have a compression test done first to eliminate the gasket
other points are: - the inlet manifold v motors use a passage in the inlet manifold to cross water between the heads at the back
if your motor is a v motor (not included in the question ) then there could be a corrosion hole in the manifold letting water in to the combustion chamber
corrosion in the head that is allowing water to the inlet manifold --won't show up in a compression test as it will be on the inlet side of the valves
any problems such as a blown head gasket , cracked head or corrosion in the combustion chamber will result in overheating of the engine so the problem ( if the compression test is good ) will be corrosion in a part that is connected to the inlet manifold such as a EGR valve

Jun 29, 2015 | Cars & Trucks

1 Answer

My au series 2 xr6 started having an engine miss after it stalled I've changed the plugs and leads ,and was told it could be a blown intake manifold gasket ?


have the OBD codes read , sounds like the coil could be the issue but the OBD will tell you where the issue lies

Jul 05, 2014 | 2004 Ford Freestar

1 Answer

What is the firing order for a 1995 ef xr8 5 litre???


Hi there:
Falcon EF is 1-5-3-6-2-4

EF has a coil pack under the inlet manifold; also keep in mind that EF uses a waste spark system so 2 plugs are fired at the same time eg 1 and 6 - 2 and 5 - 3 and 4


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Sep 24, 2012 | Cars & Trucks

2 Answers

How to replace a intake plenum gasket


Well basically, you remove the intake plenum and replace the gasket and reinstall the plenum. Here are the steps:

1. Disconnect the negative battery cable from the remote jumper terminal located at the right strut tower.
2. Remove the air inlet resonator and tube.
3. Remove the throttle actuator cables from the throttle arm and bracket.
4. Disconnect Secondary Runner Valve (SRV), Manifold Tuning Valve (MTV), Throttle Position Sensor (TPS), Idle Air Control (IAC) motor electrical connectors.
5. Remove the electrical connector and the Intake Air Temperature/Manifold Absolute Pressure (TMAP) sensor.
6. Disconnect vacuum hoses from the Secondary Runner Valve (SRV) reservoir, Speed Control reservoir, and PCV.
7. Remove right and left intake manifold supports.
8. Remove support brackets at the intake manifold front corners and MTV.
9. Loosen upper fastener attaching throttle body to support bracket.
10. Remove clips attaching EGR tubes to intake manifold.
11. Remove intake manifold bolts and manifold
12. Remove old gaskets, Clean gasket surfaces, and install new gaskets.
13. Reverse steps to reinstall manifold

Jun 16, 2012 | 1999 Chrysler 300M

1 Answer

Car stalls when hot 3.8 liter


if it is loosing coolant.. check and replace inlet manifold gasket.. head gasket... worst case it will need new head or inlet manifold.

Sep 02, 2010 | 1996 Buick Regal Olympic Gold

1 Answer

I need instructions on how to replace a fuel pressure regulator and intake gasket manifold in a 1994 Toyota 4runner. Do you know where I can get that information?


The pressure regulator should be fitted ot the fuel rail firewall end and the inlet manifold gasket on the inlet manifold when you take it off ,and the inlet manifold is the one which goes to the air filter pipe and airfilter box.

Nov 18, 2009 | 1993 Toyota 4Runner

1 Answer

Air leak on inlet manifold gasket


ive got a vw bora 2.3 v5 2001 got a hissin from inlet manifold

Apr 14, 2009 | Volkswagen Passat Cars & Trucks

1 Answer

1999 pontiac sunfire idle


It sounds like an airleak on the indution side of the inlet manifold, as the car reaches temperature the aluminium manifold will expand allowing a tiny gap to get bigger.
Try spraying WD40 around the inlet manifold gasket area, if you notice a sudden change in the way the engine is running it is a reasonable indication that some WD40 was just sucked through the leaky gasket and for an instant the car ran on WD40.
The check engine light could be the ECU telling you that you have a lean mixture. (leaking inlet manifold gasket)

Sep 22, 2008 | 1999 Pontiac Sunfire

7 Answers

Firing order for a 1996 EF ford falcon


EF & EL are 1,5,3,6,2,4
EF has a coil pack under the inlet manifold the EL has a distributor
EF uses a waste spark system so 2 plugs are fired at the same time eg 1 & 6 - 2 & 5 - 3 & 4

May 18, 2008 | 1983 Ford Fairmont

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...