Question about 1997 Toyota 4Runner

1 Answer

What could cause me to have no power to my ignition and my dash on my 97 toyota 4 runner

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 170 Answers

Do any of your lights work? Battery/? Ground Cable? Engine Ground wire? Fuse? ignition Relay?

Posted on Nov 23, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: replace front brake pad 2003 toyota 4 runner

Diagram is unnecessry.
Pull both front wheels
Work one at a time leaving the other for reference
Find the retention spring ... its a paperclip thickness wire spring... dislodge center retention loop and undo from both ends which engage brake pad retention rods.
Pull the rods out
Pull the old pads out... laying everything on the ground
Use scrap wooden wedges to pry between the rotor and the caliper ...inside and out until the calipers are fully withdrawn. Use the new pads to measure if they are far enough back.
Note... the brake fluid will have dropped in the master cylinder over many months of wear... do not fill it. When the calipers are pushed back they will fill the reservoir again... one wheel at a time.
Be sure to identify the correct pad based on what you took out and what is on the other side (if you screwed up the layout)
Make sure to take the old antisqueek backing plate from the old pad and place it on the new pad. They don't use lubricant on these anymore.
Replace the pads... the retention rods... then the retention spring
Do the other side
Then progressively step on the brake peddle until full tension is felt
Check the master cylinder reservoir... probably needs no additional fluid.
New pads will register in existing ridges in each disc in no time at all.
You should check the discs to see if they need to be replaced during this operation...using some calipers

Posted on Mar 25, 2009

  • 1 Answer

SOURCE: water leak under the intake manifold,1995 toyota 4 runner

There is a heater core bypass pipe that runs from the block (under the manifold) to the bacl of theengine where you will see a flat rectangular "sheet metal" thing with a pipe coming out of it. The a rubber hose connects. You need to pull the top air plenums and intake to get to it. The p[ipe flange bolts to the block with silicone rtv as a sealant.

Posted on Nov 27, 2009

Testimonial: "thanxs"

satitus
  • 273 Answers

SOURCE: need to replace clock

I have the instructions and repair solution at www.autoclockrepair.com

Posted on Jan 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Toyota 4Runner Shimmy, Pull and Lunge


Well, I used to meet this kind of problems before. A master told me to used a Toyota tool called mini VCI. Very easy to use. Very powerful function.

Jul 20, 2012 | 2005 Toyota 4-Runner SR5

1 Answer

The key in the ignition of our 97 4-runner will not turn at all. car did start yesterday with no problem. it is really cold out today and wonder if that has anything to do with problem


Could be that frozen condensation is preventing stuff from turning. If you can use an extension lead and use a hot hair dryer to help defrost things.

Jan 23, 2011 | Toyota 4Runner Cars & Trucks

2 Answers

Where is the flasher relay located for 1998 Toyota 4- Runner


Toyota Pick-ups, Land Cruiser, and 4 Runner 1997-00
Flashers -REPLACEMENT

The turn signal flasher is usually located in the convenience center, under the dash, on the left side kick panel. In all cases, replacement is made by unplugging the old unit and plugging in a new one.

Hope helped with this (remember rated this help) Good luck.

Nov 09, 2009 | 1998 Toyota 4Runner

1 Answer

2002 toyota 4 runner timing belt change interval


100 000km timing belt light on dash should come on when due

Jul 09, 2009 | 2002 Toyota 4Runner

1 Answer

I have an 87 4 runner and the dash lights are flashing with the indicators and it is also lacking in power and blowing fuses under the dash can you please help me


Sounds like a bad ground, OR the wiring harness to the ignition switch / headlights switch is bad.
I just replaced mine because the interior lights kept blowing a fuse and the clock did not work.
Everything works now.
Replacement wiring harnesses/switches are available at most auto parts stores. Get a Haynes manual and a steering wheel puller to do this repair. Pretty easy & cheap repair.
Good luck :)

Jul 07, 2009 | 1987 Toyota 4Runner

1 Answer

1987 toyota 4 runner


Check your battery terminals, supply cables and battery earth connections are in good order.

Jun 17, 2009 | 1987 Toyota 4Runner

Not finding what you are looking for?
1997 Toyota 4Runner Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...