Question about 2007 Ford Crown Victoria LX Sedan

1 Answer

Vic fuse diagram

HEATER FAN NOT BLOWING AT ALL

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,687 Answers

This is usually because of a bad fan resistor control. Track the wires under the hood from the blower fan to a part stuck in the underhood ductwork shell. This part can sometimes be reactivated by tapping on it with a broom handle. Just look for a part with 2 bolts and 1 plug-in harness.

If you are not successful in reactivating your part, you will have to replace it. One thing good about checking this is that you can remove the wires from the old part and plug in the new part before making any other changes. If it now works, proceed to installing the new part.

Sometimes a water hose is in the way at the rear of the engine. Do it this way. Cold engine. Remove attaching bolts and wires. Have new part in reach for 1 handed swap. Loosen heater water hose clamp and prepare to remove end of hose. Pull hose off engine, pinch and hold hose with 1 hand, change resistor with other hand and leave new part loose in ductwork. Replace hose to engine.

Because you did this on a cold engine, a vacuum lock should keep the water from rushing out of the heater hose that you pinched and held.

Posted on Nov 23, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 Ford Explorer Defrost Heater isn't blowing any air to the defrost Is this a fuse?


If your front blower motor isn't working on any setting, could be the blower motor itself, the blower resistor, or sometimes the wire pigtail to either one could be the problem.

Oct 23, 2017 | Ford Cars & Trucks

1 Answer

The 10 amp fuse that goes to the turn signals and heater fan keeps blowing on my 1997 dodge caravan


That fuse circuit goes hot with the key on, shouldn't have voltage before you turn the key on. The fuse circuit sends voltage to several circuits, one of which is the front blower relay. Unplug the relay, see if fuse still blows? If you need to enlarge diagram, sometimes you can click on your highlited post, on that page you may be able to enlarge diagram.

26396132-tavfdk2k0uapnfdvrreqvksd-5-0.jpg

26396132-tavfdk2k0uapnfdvrreqvksd-5-2.jpg

Dec 12, 2016 | 1997 Dodge Caravan

2 Answers

Mitsubishi L200 Fan Heater blower Fuse keeps blowing


Why does the heater fuse keep blowing
This place offers a few suggestions, like fan motor old and pulling too much current, or fan switch, ect

Nov 23, 2015 | Mitsubishi Cars & Trucks

1 Answer

Does a 2009 crown vic have a heater control valve if so where is it located


yes its a blender door accuater some are vacuum controlled and some electric, and ther is a heater control valve under hood on passengers side tward fire wall ,its in the heater hose line.

Oct 17, 2014 | Cars & Trucks

1 Answer

2002 tracker,keeps blowing 15 amp fuse that runs heatr fan and lets car shift out of park


I looked at the wiring diagrams and those two circuits should be on two different fuses.
The shift lock solenoid is powered by the 10amp turn signal fuse and the 15amp stop light fuse. If the fuse blows when you put it in park, I would say the shift lock solenoid is the problem and the stop light fuse is the one that is blowing.
The heater fan and relay are powered by a 60amp fuse and a 15amp fuse but not the stop light fuse.
Its possible there is a short some where that has connected these two circuits.
You could disconnect the shift lock solenoid to see if the fuse still blows.

Jan 21, 2013 | 2002 Chevrolet Tracker

1 Answer

1988 bmw 325is heater keeps blowing 30amp fuse, tried to find a short but me heater blower fan isnt working what could be the problem. cant keep a fuse without blowing


More than likely the fan motor its self is short to ground try to unhook the wires to the fan motor and install a new fuse and then turn the fan on with the wires removed and if the fuse is still good you know it is the fan motor its self

Feb 12, 2010 | 1988 BMW 3 Series

2 Answers

The heater blower motor on my 2001 ford crown vic won't work. i checked the fuse and took the motor out and had it checked and it's OK.


look for relay or resistor heater box under hood passenger side follow heater hoses 2 two heater box coming out of fire wall

Jan 25, 2010 | 2001 Ford Crown Victoria

1 Answer

Where does a heater fuse go in a 1999 crown vic


Under the dash to the lreft of the steering wheel you will find the fuse box, it will have a black plastic cover over it, remove the cover and look at the diagram printed on the cover, the heater blower motor fuse is #9, it is a 30 amp fuse.

Let me know if this helps.

Lone99star

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jason_77a19afa8d604dee

Jan 11, 2010 | 1999 Ford Crown Victoria

Not finding what you are looking for?
2007 Ford Crown Victoria LX Sedan Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...