Question about Cars & Trucks

Open Question

How do you remove governor from 212cc predator engine

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 295 Answers

SOURCE: I have installed a predator 212cc ohv motor on go

Meaning no torque to the wheels --> First suspect: Gearbox.

Posted on Jun 27, 2014


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove speed governor on 2000 park avenue

You have to access your computer. There are products you can buy to tap into it, (one is Predator by Diablo) or a dealership can do it also....

Dec 29, 2016 | Cars & Trucks

1 Answer


It likely has a governor which limits speed. Used on rentals alot. Was it a rental at one time?
Read the sheet on this page under "Check Operation" F1 F2 F3 "Governor cut-out pressurekPa (psi) Governor cut-in pressurekPa (psi) Verify warning lamp and alarm operation (F-650/F-750 Only)"and notice the governor."

See it (blue box I drew over it on pic below) on pgs. 328-330 of manual (takes FOREVER to load! Its a big pdf).
here it is (OK so its below)

Pg.396 says under 7. "7.Installation of a gasoline engine speed governor is permissible, provided the governor design is compatible with each respective throttle body for the individual engine application and it does not exceed specified engine maximum RPM. It must also meet all noise and engine emission requirements. Governor installations may affect electronically controlled transmissions. Contact Ford Truck Body Builders Advisory Service before installing."

Since its saying it CAN be installed then it obviously can be uninstalled to be like original.

Get it removed? :)

Kind Regards,

25413078-r134pvufqxkme5zfg0hx2zyu-3-1.png Their Ford feet manual.

Feb 11, 2015 | Ford Cars & Trucks

1 Answer

How do I find the size of the clutch belt for a predator 212cc

Remove the old one and take it to the spares shop

Sep 28, 2014 | Cars & Trucks

1 Answer

How to obtain fuel tank for a 212cc 6.5hp Pedator engine from harbor freight

im sure if you call them they can help, or take it to a bridgs and stration dealer and see if they have a match or can order one for you.

Sep 11, 2014 | Cars & Trucks

1 Answer

Removal of the Speed Governor

If its a gas engine its controlled by the engine computer.

Jan 17, 2014 | Chevrolet C1500 Cars & Trucks

1 Answer

2004 jeep code 1763 what to do

P1763 - Governor Pressure Sensor Voltage Too High

This code is refer for the governor pressure sensor which is located in the valve body of the transmission. If getting power to the sensor and the wires are not open or shorted then the sensor will need to be replaced.


Hoist and support vehicle on safety stands.
Remove transmission fluid pan and filter.
Disengage wire connectors from pressure sensor and solenoid (see picture)
Remove screws holding pressure solenoid retainer to governor body.
Separate solenoid retainer from governor (see picture)
Pull solenoid from governor body
Pull pressure sensor from governor body.
Remove bolts holding governor body to valve body.
Separate governor body from valve body
Remove governor body gasket.

Before installing the pressure sensor and solenoid in the governor body, replace O-ring seals, clean the gasket surfaces and replace gasket.

Place gasket in position on back of governor body
Place governor body in position on valve body.
Install bolts to hold governor body to valve body.
Lubricate O-ring on pressure sensor with transmission fluid.
Align pressure sensor to bore in governor body.
Push pressure sensor into governor body.
Lubricate O-ring, on pressure solenoid, with transmission fluid.
Align pressure solenoid to bore in governor body
Push solenoid into governor body.
Place solenoid retainer in position on governor
Install screws to hold pressure solenoid retainer to governor body.
Engage wire connectors into pressure sensor and solenoid Install transmission fluid pan and (new) filter.
Lower vehicle and road test to verify repair.





Hope helps.

Sep 29, 2011 | 2004 Jeep Grand Cherokee

1 Answer

I have a 1998 murcery villager. there is an assessory box attached to the covering of the driver side axel ampl assy-ws/w f4xa17a431aa 28510 ob710 et20 123 12 v jideco i believe this has something to do...

go to our villager site for help. The wiper motor has a governor assy, that is what you are referring to. What is the problem?
Windshield Wiper Governor Removal
The windshield wiper governor (17C476) is located on the LH side of the engine compartment behind the battery (10655) .
  1. Remove the two windshield wiper governor screws and the windshield wiper governor .
  2. Disconnect the two windshield wiper governor electrical connectors.


Apr 05, 2010 | 1998 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides