Question about 2006 Land Rover Range Rover Sport

Open Question

Driver's Door Window Motor Initialisation - 2006 Land Rover Range Rover Sport

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the right front door panel on a 2004 buick le saber


Did you test it or are you guessing just because it won't open or close ? How To Install Remove Front Door Panel Buick Lesabre 00 05 1AAuto com both right an left are the same .
Power Windows System Components
The following components are used to control the power windows:
?€¢
Driver Door Module (DDM)


?€¢
Passenger Front Door Module (PDM)


?€¢
LH Rear Door Module (LRDM)


?€¢
RH Rear Door Module (RRDM)


?€¢
Driver Door Switch Assembly (DDSA)


?€¢
RH Front Power Window Switch


?€¢
LH Rear Power Window Switch


?€¢
RH Rear Power Window Switch


?€¢
LH Front Power Window Motor


?€¢
RH Front Power Window Motor


?€¢
LH Rear Power Window Motor


?€¢
RH Rear Power Window Motor


?€¢
Class 2 serial data circuit


?€¢
Power door serial data circuit


?€¢
PWR WDO 30 Amp Circuit Breaker


?€¢
DRVMDL Fuse (10 amp)


Driver Door Switch Assembly and Driver Door Module logic, Driver Door Module internal driver operation


?€¢
PASS MDL Fuse (10 amp)


Front Passenger Door Module logic and internal driver operation


?€¢
RRDR MDL Fuse (10 amp)


Left Rear Door Module and Right Rear Door Module logic and internal driver operation


Do you know about computer controlled power windows ?
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.

Oct 30, 2016 | Buick Cars & Trucks

1 Answer

NEED TO REMOVE DOOR PANEL ON A 2004 CHEVY AVEO


Click the link below:-----Door Panel Removal?

--------
How to remove the door panel to install a new window regulator?
http://howtobyme.blogspot.com/2011/08/how-to-remove-door-panel-to-install-new.html


---------
Hummer H2 Door Panel Removal? http://technoanswers.blogspot.in/2012/07/hummer-h2-door-panel-removal.html Hummer H2: How to remove Front Door panel? http://www.howtobyme.blogspot.com/2012/07/hummer-h2-how-to-remove-front-door.html 2009 Hummer H2 Door Panel Removal http://schematicsdiagram.blogspot.in/2012/07/2009-hummer-h2-door-panel-removal.html

-----------
how to remove window motor on driver side door panel?
http://technoanswers.blogspot.com/2011/08/how-to-remove-window-motor-on-driver.html


-----------
ford explorer window motor, regulator and door panel removal?
http://technoanswers.blogspot.com/2011/02/ford-explorer-window-motor-regulator.html


---------
Keep updated for more help.

Nov 19, 2012 | Cars & Trucks

1 Answer

Why my passenger window don't work ?


If neitrher the driver's door master switch nor the passenger door window switch wont operate the window, and the lock-out button is not on, then likely the passenger door inner panel has to come off to investigate. But first, check the wiring going into the passenger door for a broken wire. Also check the wiring coming out of the driver's door. If you see nothing wrong, pull off the passenger door panel and check for any wires loose from the window switch down to the motor. You can hotwire the window motor with a spare battery set beside the door there, to verify the motor is bad. If it is bad, you have to remove the glass, then remove the window regulator with motor attached, in order to replace the motor.

Nov 14, 2012 | 2004 Ford Mustang

1 Answer

How to reset driver window motor in 2006 BMW 750


Press the window 'open' switch beyond the second switching position. When the window has reached the lower final position, operate the switch for at least 15 seconds but not longer than 25 seconds. Then let go of the button and immediately pull the switch beyond the 'close window' position. Do not let go of the switch! The window now moves into the top final position, stops, then moves to the lower final position, stops again and then moves back to the upper final position. The switch must be held in the "pulled beyond engaging point" position during the entire procedure. Once the window has reached the upper final position, the initialisation is complete.

Jan 14, 2012 | 2006 BMW 750Li

1 Answer

I have a 06 trailblazer, and my drivers window will not go down. I had the motor cahnge it and is still not working. WE even took the switch out of the drivers door and connected it to the passenger door...


Are you aware of the fact that there are door modules ? Controlled electronically !
Power Window Inoperative - Driver Door
2
Operate the driver power window in the UP and DOWN directions.
Does the driver power window operate properly?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Install a scan tool.
Monitor the Driver Window Status Data parameter in the driver door inputs list.
Does the Driver Window Status Data parameter display an active state?
YES - Go to Step 11
NO - Go to Step 4
4
Monitor the Driver Window Status Data parameter in the driver door module (DDM) inputs list.
Activate the driver power window switch in the up and down positions.
Does the Driver Window Status Data parameter change accordingly?
YES - Go to Step 5
NO - Go to Step 11
5
Connect a test lamp to a good ground.
Backprobe the battery positive voltage circuit at connector C1 cavity D.
Does the test lamp illuminate?
YES - Go to Step 6
NO - Go to Step 13
6
Disconnect the driver power window motor.
Connect a test lamp to a good ground.
Probe the power window motor up control circuit at the power window motor harness connector.
Activate the power window switch to the UP position.
Does the test illuminate?
YES - Go to Step 7
NO - Go to Step 9
7
With the test lamp still connected to a good ground, probe the power window motor down control circuit.
Activate the power window switch to the DOWN position.
Does the test lamp illuminate?
YES - Go to Step 8
NO - Go to Step 10

You probably have a bad door module .

May 21, 2017 | Chevrolet TrailBlazer Cars & Trucks

2 Answers

I have a 2001 olds aurora. the only door that works is the driver. none of the other windows, door locks, or pass power mirror work. i installed a new window switch on the drivers door and that didnt...


At the moment, I'm just talking about the front passenger side window. On the hinge side of passenger door, should be wiring harness, probably has protective covering, pull the covering back to expose wire colors. Note the wire colors for battery and ground. Battery is voltage, use a test light, check both orange wires for voltage. You can use to testlight also to check ground, check both grounds. With test light connected to battery voltage, probe the ground wire, both of them, if the lite comes on, at least the ground is good enough to turn on the test light.
passenger window-0pkbgv2qrbrqq4t3zadvwxxw-1-0.jpg

May 31, 2017 | 2001 Oldsmobile Aurora

1 Answer

Driver door window will not move. The motor makes


possible broken motor cable or motor gear that move your window up and down, need visual inspection...

Feb 03, 2010 | 1994 Toyota Camry

6 Answers

Windows won't roll down


Does the rear window work from the passenger switch?

Oct 07, 2009 | 2003 Cadillac CTS

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...